Yamaha FZ-1 TiForce exhaust system Installation Instructions (Slip-on)

0

Filed Under (Yamaha) by admin on 03-01-2012

download
Loosen the clamp where the stock tailpipe connects to the stock collector. 2. Remove the bolt holding the stock muffler assembly to the footpeg/exhaust bracket. 3. Remove the stock tailpipe and exhaust assembly as one piece. 4. Remove the nut securing the right side center stand support bolt. Install the new supplied bracket as shown in (See figure 1) 5. Remove the right rear footpeg assembly complete, bolt the new footpeg mounting bracket in place of the stock one using supplied bolts. 6. Carefully unbolt the footpeg from the bracket (Be careful there are springs and washers that will fall out if you are not careful), bolt the footpeg into the new billet footpeg bracket. Bolt the footpeg bracket to the footpeg- mounting bracket. (See figure 2) 7. Remove the stock exhaust gasket from the stock tailpipe and installthe gasket into the new tailpipe. 8. Slide the supplied clamp over the new tailpipe and slide the new tailpipe onto the stock collector. 9. Slide the TiForce end can into place. Loosely attach the two rubber bands, stainless steel bands K, and stayarm / hanger G to the end can using the supplied 6mm hardware H. See figure 4. 10. Place the bands approximately 150mm from the edge of the end can. See figure 5. 11. Using the stock provided mounting point on the passenger footpeg, and using the stock mounting bolt, mount the end can loosely, allowing for some adjustment. Insert the stock mounting bolt through the stay / hanger G. 12. Attach the supplied springs to connect the tailpipe and muffler assembly. 13. Make sure the exhaust system is free and clear, if necessary jigglethe system to adjust for proper clearance. 14. Carefully align the two stainless bands K so that they are parallel to each other, and spaced properly on the can (figure 5), then tighten the 6mm hardware H and the stock mounting bolt hardware. Make sure thatthe rubber pads fully cover the band(s). USE CAUTION WHEN TIGHTENING THE 6MM HARDWARE AND THE TWO BANDS SO AS NOT TO CRUSH OR DISTORT THE SLEEVE OF THE CAN. 15. Tighten the supplied clamp to secure the new tailpipe to the factory collector. 16. Using some brake and contact cleaner on a clean rag, carefully wipe down the entire exhaust system to remove any residual oils, anti seize, fingerprints and dirt prior to starting the motor. FAILURE TO CLEAN THE TUBING AND CAN MAY RESULT IN PERMANENT STAINING OF THE SYSTEM WHEN HEATED. 17. Check that all hardware is tightened, then start the motor and check for exhaust leaks.

2006-2007 Honda TRX450R SR4 4 Stroke racing system INSTALLATION

0

Filed Under (Honda) by admin on 30-11-2011

download
Install Motoworks header pipe using stock nuts, finger tight at this point ( Fig 4) 2. Install Motoworks tailpipe with muffler using bolt and spacer supplied in kit on upper rear mount, use stock nut and bolt on lower mount finger tight at this point. (Fig 5 and 6) 3. Torque header pipe nuts to 1.0 kg-m ( 7.3 lb-ft ) 4. Torque tailpipe mounting bolts to 2.5 kg-m ( 18 lb-ft ) 5. Re-check all your work 6. We recommend that you clean the entire exhaust system with a mild detergent, i.e. glass cleaner prior to starting as any oily residue may cause permanent stainingBefore operating check for proper clearance between Motoworks exhaust and ATV i.e. frame, plastic, brake line, fuel line etc if problems exist re-check work

Harley Davidson Sportster 2 into 1 SS2 R Race Exhaust System Instalation Manual

0

Filed Under (Harley Davidson) by admin on 20-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Loosen the heat shield clamps on both front and rear exhaust pipes. 2. Remove the two mounting nuts from each head pipe, located at the cylinder head. 3. Remove the nut that mounts the front muffler to the engine, located below the rear brake pedal. 4. Remove the bolt that mounts the rear muffler to the mounting bar. 5. Remove the entire exhaust system and set it aside. 6. Carefully remove the flanges and circlips from the stock exhaust system using snapring pliers. Note : If circlips look bent or twisted replace them with new circlips. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Remove the acorn nut that mounts the top of the right rear shock to the frame. 2. Install the large angle cut end of the new mounting bar to the shock bolt (with the shock in place). Replace the acorn nut but leave it loose at this time. Note : Check the clearance between the mounting bar and the shock. Space the mounting bar out with a washer (not supplied) if needed. 3. Install the circlips and flanges from the stock system onto both of the new head pipes. 4. Check the stock exhaust gaskets to be sure they are in good shape. If you have any doubts as to their condition, replace them. 5. Install new header using the stock nuts and tighten them evenly. 6. Slide the tailpipe of the new exhaust system over the collector of the front header. 7. Install two of the exhaust springs (supplied) between the collector and the tailpipe using the spring puller tool (supplied). 8. Slip the silencer over the tailpipe while aligning the hole in the mounting bar with the hole on the top of the muffler, with the muffler positioned to the outside of the mounting bar. 9. Install the bolt, washers and lock nut (all supplied) through the muffler and mounting bar. 10. Install the two exhaust springs over the tabs on the muffler and tailpipe using the spring puller tool. 11. Tighten the acorn nut on the top of the right rear shock. 12. Be sure to tighten all hardware before starting your motorcycle. 13. Important: Check to be sure that there is adequate clearance between the head pipe and the rear