2008 Harley-Davidson TOURING INJECTION FUEL INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 29-03-2012

download
1. Remove seat, exposing factory computer (ECU). disconnect factory wiring by pressing lock and pushing lever back. 2. Remove ECU by pushing tab and sliding the ECU to the right as you lift. 3. Gently align the pins of the Fuelpak connector with the ECU and press the connector on the ECU. Be sure the single large pin is aligned with the single large socket before pressing Fuelpak connector into the ECU. Make sure all four tabs fully latch. (Fuelpak connector Patent Pending# 29 295831) 4. Connect factory wiring to Fuelpak connector and pull lever to locked location. Be sure that lock snaps into position. 5. Reinstall ECU. 6. Remove left side cover. 7. Slide Fuelpak down through opening leading to the area under the left side cover. 8. Attach Fuelpak to the fuse cover using supplied velcro.
HOW IT WORKS ENTERING VALUES 1. Remove Fuelpak clear case cover by removing all four screws, save hardware . 2. Turn on main power and handlebar switches, but do not start engine. Fuelpak display should light up, if not, turn power off and verify the connectors are fully seated. 3. Refer to Fuelpak Setting Reference to locate the Setting Values specific to your bike and exhaust system. If you do not find your setting, visit fuelpakfi.com or call tech support at (562) 921-0071. 4. Starting with mode 1 selected, press the value (+) or the value (-) buttons to input the correct value as indicated in your Setting Value. After entering your first value, press the mode select button to move to mode 2 and enter the value. Continue until you have entered the value for each of the first 18 mode positions. Each time the value (+) is pressed, the value increases by one number. Each time the value (-) is pressed, the value decreases by one number. (Please refer to the “How It Works” section directly above if you have questions about this step. 5. By pressing the mode select button 3-times, move to mode 21 and verify that it reads “0″ 6. Enter any other mode values as required for your application. 7. Turn power off, wait one second then turn power back on. Verify all modes then turn power off. 8. Reinstall Fuelpak clear cover then reinstall side cover

Suzuki Electronic Jet Kit Installation Instructions

0

Filed Under (Suzuki) by admin on 12-02-2012

download
at anytime during install or tuning please callus for any and all help, we can’thelpifyoudon’tcall ) 1. Before installing the TFI you must first disconnect the negative lead from the battery. 2. Determinea location for the TFI unit. Suggested locations areas follows: Under the seat, behinda side cover or tail section. 3. The TFIcomeswitha harness with injector connectors that match the factory injector connectors. 4. Locate the factory fuel injectors (see owners manual if you are not sure).** **: Some models are equipped with two sets of injectors (primary and secondary); the unit is designed to interface with the primary injectors. If the TFI harness does not match your injectors do not proceed and call tech support at 877-764-3337. 5. Disconnect the factory injector connectors from the fuel injectors and replace with the TFI injector connectors from the TFI unit, basically unhook the factory injector connector and plug the matching TFI connector (female) to the injector and then connect the factory injector connector to the TFI connector that simulates the injector (male). There is no order to hookup the TFI harness to the factory harness just make sure the original factory connector goes toits’original cylinder. It isa good idea to make sure there is a little slack in the harness to prevent engine vibration from damaging/breakingawireon the connectors. 6. Be sure to check the wires are not indirect contact with any sharp edges, exhaust and/or other objects, which could result in long term wear and/or damage. 7. Connect the TFI ground lead to the negative terminal of the battery along with the factory ground lead. 8. With the rubber plug removed from the TFI, turn the motorcycle key switch to the “ON”position. As the bikes electrical system goes through initial startup mode you may see LED’sflashingonthe TFI.