Automatic Transmission/ Transaxle Fluid Level Inspection Temperature Rang es

0

Filed Under (Toyota Manuals) by admin on 12-10-2011

download
For vehicles equipped witha transmission requiring the use of the overflow type automatic transmission fluid (ATF) inspection process, the A TF must be withinaspecific temperature range for accurate fluid level inspection. Inspecting the A TF outside of the specified temperature range may result in incorrectA TF fluid levels and could lead to shift quality, M.I.L. “ON”, and/or transmission damage issues. Please seethe information in this bulletin for updated A TF level inspection temperature ranges. HINT For additional information including animations and video illustrations, please seethe Technical Training course E076: “Toyota ATF Level Inspection”. NOTE Please see TSB No. TC 010-07, “World Standard Automatic Transmission Fluid”, for important tips when working with A TFWS. ©2008 ToyotaMotor Sales, USA Page 1of3
T-SB-0129-08 July9,2008 Page 2of3 Automatic Transmission/Transaxle Fluid Level Inspection Temperature Ranges Warranty Information OP CODE DESCRIPTION TIME OFP T1 T2 N/A Not Applicable to Warranty – - — Parts Information PREVIOUS PART NUMBER CURRENT PART NUMBER PART NAME QTY 00289-ATFWS Same ATFWS As needed Required Tools&Equipment

Incoming search terms:

HARLEY DAVIDSON SADDLEBAG LID ORGANIZER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 07-03-2011

download
installation NOTE Prior to installation, hold each organizer up to the lid (without removing the adhesive backing tape) to verify that the organizer fits properly within the recess of the saddlebag lid before moving on to the installation. 1. Use the isopropyl alcohol wipes included in the kit to thoroughly clean the interior surface of both saddlebag lids. Make sure any residue is removed, then allow the lids to dry completely. Make sure the lid surface is free of condensed moisture. NOTE The ideal temperature range for applying the tape is 70 to 100 degrees F (21 to 38 degrees C). Minimum application temperature is 50 degrees F (10 degrees C). If you attempt to apply the tape below these temperatures, the adhesive will become too firm to adhere properly. 2. Locate the double-sided tape on back of the left lid organizer and remove the backing material. NOTE When performing the next Step, be sure to apply pressure to entire length of tape to ensure proper activation of pressure- sensitive adhesive. 3. Carefully center the left lid organizer in the left saddlebag lid recess and press firmly into place. While applying opposing force from outside of lid (to minimize force on tether, hinges, etc.), apply moderate pressure around entire perimeter of organizer and in middle (making sure to include all areas of tape contact). 4. Repeat Steps 2 and 3 on the right saddlebag lid with the right saddlebag lid organizer. 5. Allow the tape to cure (“wet-out”) for a minimum of 48 hours at 70 degrees F (allow extra time if temp is below 70 degrees). Do not place items in the Lid Organizer while the adhesive is curing

HARLEY DAVIDSON TOUR-PAK WALL ORGANIZER INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
This kit fits 1997 and later models equipped with King Tour- Paks INSTALLATION NOTE Maximum Wall Organizer weight capacity is 3 pounds (1.4 Kg) evenly distributed. Do not exceed tour-pak weight capacity. Too much weight can cause loss of control, which could result in death or serious injury. (00401b) Tour-Paks With Molded Liner 1. Remove the two nuts that hold the pouch and liner in the Tour-Pak. Remove pouch and liner and carefully wash the inside of the Tour-Pak with warm, soapy water. Rinse and dry thoroughly. 2. Use the alcohol prep pad in the kit to thoroughly clean the interior surface of the Tour-Pak sides where fastener strips will be attached. Make sure any residue is removed, then allow Tour-Pak to dry completely. Make sure the surface is free of condensed moisture. NOTES The hook and loop fastener strips and organizer must be installed below the edge of Tour-Pak base to avoid interference with top gasket and lock. The ideal temperature range for applying the fastener strip is 70-100° F (21-38° C). Minimum application temperature is 50° F (10° C). If you attempt to apply the tape below these temperatures, the adhesive will become too firm to adhere readily. 3. See Figure 1 and Figure 2. Remove the hook and loop fastener strips from the hinged hook and loop strips. Remove the paper backing and firmly press the fastener strips into the locations (1) shown in Figure 2. The fastener strips should be located approximately 1/8 in. (3 mm) below the edge of the Tour-Pak base. 4. See Figure 1. Bend the hinged hook and loop strips (3) into shape as shown. Attach the hinged strips onto the fastener strips (2) installed in Step 3. NOTE The Tour-pak Wall Organizer installs in place of the pouch removed in Step 1, therefore the pouch will not be re-installed. 5. Reinstall the liner removed in Step 1. The hinged strips (3) will go over the top of the liner (4) as shown in Figure 1. 6. See Figure 1. Attach the organizer (5) to the hinged strips (3). Adjust the organizer’s lock cut out so that it is centered around the lock, and press the hook side of the hook and loop strips on the bottom of the organizer into place on the liner. The hook side will attach to the liner. NOTE 2006 and later Tour-Paks equipped with Passenger Backrest will have two acorn nuts at the front of the base. Remove and discard the 8 in. (200 mm) long hook and loop hinged fastener strip from the center panel. In one of the organizer pockets there will be 4 in. (100 mm) and 1-1/2 in. (38 mm) hook and loop hinged fastener strips. Install the hinged strips on the organizer center panel as shown in Figure 3. 7. Check to make sure the Tour-Pak lid closes over the organizer and the lock works without interference. Adjust as necessary. 8. Allow tape to cure (“wet-out”) for a minimum of 48 hours at 70° F (21° C) (allow extra time if temperature is below 70°). Do not place items in the Wall Organizer while adhesive is curing

Incoming search terms:

Baja BA 250 ATV OWNER'S MANUAL

0

Filed Under (Bajaj) by admin on 26-11-2010

download
FUEL AND OIL FUEL Proper fuel is very important for the engine. Ensure there is no dust, dirt, or water which has mixed in the fuel. Use regular unleaded gasoline with an octane number 90 or higher. ENGINE OIL Your 250cc ATV has a four-stroke engine. Please use oil as described in the chart below. By using prescribe oil, you will realize the best lubrication for engine. Use the chart to select a viscosity rating based on the temperature range in your area. NOTE: In very cold weather (below 5°F (-15°C), use SAE10W-30 for good starting and smooth operation. SAE 10W-30 SAE 20W-40 ENGINE TEMP. °C °F -30 -22 40 104 -10 14 0 32 10 50 20 68 30 86 -20 4 FUEL AND OIL 8 LOCATION OF LABELS Read and follow all of the warnings labels on your ATV. Make sure you understand all the labels. Keep the labels on the ATV. Do not remove them for any reason. If a label comes off or becomes difficult to read, you should get a replacement by contacting BAJA INC. 1 – Red Light – Reverse indicator Light illuminates when ATV is in Reverse. 2 – Green Light – Neutral indicator Light illuminates when ATV is in Neutral. 3 – Ignition key switch – Turn right (CW) “RUN”, Turn left (CCW) “OFF”. ATV will only start when ignition key is turned to the “RUN” position. Make sure ignition key switch is in the “OFF” position when not in use

Incoming search terms:

Incoming search terms: