YAMAHA YFM 350 Removing stock carburetor and cables.

0

Filed Under (Yamaha) by admin on 19-01-2012

download
Remove seat and gas tank. Make sure fuel petcock is in “off” position. 2. Remove throttle cable paying close attention to routing, as the new cable (s) will need too be routed the same. 3. Remove stock carburetor and stock throttle housing. Preparing motor for carburetor install 1. Remove stock manifold from cylinder head. 2. Place supplied o’ring into aluminum flange as pictured in figure 1. Figure 1. 3. Install aluminum and rubber flange to motor using supplied bolts. See Figure 2. The shorter 25mm bolt will need to be placed in the bottom hole. IMPORTANT NOTE: Install the aluminum flange with the o’ring towards the motor and the thick side up.

Incoming search terms:

HARLEY DAVIDSON PREMIUM SUSPENSION KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 09-03-2011

download
REMOVAL Front Fork Assembly 1. Refer to the XR model section of the service manual and remove the front forks. INSTALLATION Front Fork Assembly 1. Install front forks from kit to motorcycle according to service manual instructions but do not tighten the fork bracket pinch screws at this time. 2. See Figure 1. Measure the distance from the top of upper fork bracket to top of fork assembly. Both sides must be exactly the same and measure 0.388-0.468 inch (9.85- 11.89 mm) above the top fork bracket. Align the adjustment screws inline with the handlebars (see Figure 5). is06083a Figure 1. Fork Installation Height Measurement. NOTE If new pinch screws are not readily available, use a wire grinder wheel to remove all remaining lock patch from original pinch screws, wash screws in clean solvent and dry thoroughly. Apply two drops of LOCTITE® 262 to the first 1/4 in. (6.35 mm) of the end threads. 3. Install pinch screws to upper and lower fork brackets. 4. Verify fork tube installation measurement is 0.388-0.468 inch (9.85-11.89 mm). 5. Tighten pinch screws to 30-35 ft-lbs ( (40.7-47.5 Nm)) See Figure 2. The top edge of reflector should be 1-1/2 inches (38.10 mm) below the lower edge of the bottom fork clamp. 6. Remove the adhesive backing. Place reflector in position and press reflector firmly into place to activate the adhesive. Repeat for reflector on opposite fork. REMOVAL OEM Rear Shock Absorbers 1. Refer to the XR model section of the service manual and remove the rear shock absorbers. INSTALLATION Rear Shock Absorbers 1. See Figure 3. Install the rear shock absorbers according to service manual instructions. The shocks are installed with the external gas reservoir to the rear of the shock absorbers and the thick side of the grommet installed to the frame rail mounts. is06142 Figure 3. Install Thick Side Of Grommet To Frame Rail SUSPENSION ADJUSTMENTS Front Fork Suspension Adjustment Whenever a wheel is installed and before moving the motorcycle, pump brakes to build brake system pressure. Insufficient pressure can adversely affect brake performance, which could result in death or serious injury. (00284a) Adjust both forks equally. Improper fork adjustment can lead to loss of control, which could result in death or serious injury. (00124c) Compression and rebound adjusting valves may be damaged if too much force is used at either end of the adjustment range. (00237a) NOTES Damping is set at the factory for the average solo rider under normal riding conditions. The rider may make adjustments to compensate for individual riding styles and varying road conditions. Evaluating and changing the rebound and compression damping is a very subjective process with many variables and should be approached carefully. The front and rear preload setting will need to be adjusted for the rider’s weight and cargo. This adjustment should be made before the motorcycle is ridden any distance and after changing the overall vehicle weight (adding saddlebags, etc.). If the preload adjustment is correct, and you have the rebound and compression damping set at the factory recommended points, the motorcycle should handle and ride properly. Changes in the load carried requires changes in the preload setting(s). Carrying less weight than was used for setting up the suspension requires decreasing the amount of preload. Increasing the load carried requires adding more preload. The following tools are needed to make suspension adjust- ments. • 5 mm hex key (front fork preload adjustment tool). • Spanner wrench with extension handle (shock absorber preload adjustment). • Screw driver (front fork damping adjustment). 1. Front fork preload adjustment: a. See Figure 4 and Table 1. Using the 5 mm hex key, turn the preload adjuster counterclockwise until it stops. This is the minimum preload setting. b. Turn the preload adjuster clockwise the recommended amount specified for the rider weight

Incoming search terms:

Incoming search terms: