HARLEY DAVIDSON FRONT FORK STEM BOLT CHROME COVER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 17-04-2011

download
INSTALLATION 1. See Figure 1. Remove stock front fork stem bolt and washer (if equipped). 2. Install front fork stem bolt (2) and washer (3) from this kit. Properly adjust fork stem bearings. Improper adjustments affect stability and handling, which could result in death or serious injury. (00301a) 3. Perform the steering head bearing adjustment procedure following the instructions in the service manual. 4. Apply a small amount of LOCTITE 243 Threadlocker and Sealant (Blue) (purchased separately) to the threaded stud inside the chrome cover (1). 5. Install chrome cover to fork stem bolt. Tighten cover hand- tight. Do not over-tighten. SERVICE PARTS 1 2 3 is06245 Figure 1. Service Parts: Upper Fork Bracket Bolt Cover Kit (Typical Bracket Shown) Table 1. Kit Contents Part Number Description (Quantity) Item 45668-90 Cover, front fork stem bolt chrome 1 4453 Bolt, 5/8-18 x 1.0 inch 2 6655 Washer, 5/8 inch

HARLEY DAVIDSON SADDLEBAG HINGE STOP KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-04-2011

download
INSTALLATION 1. See Figure 2 and Table 1. Remove the saddlebag by opening the lid and turning the two bail head studs (1) 1/4 turn. Save the washers (A) and discard one of the studs (1). The rear stud and isolator will be replaced with new ones from the kit. NOTE Do Not remove the hinge assembly from the saddlebag lid. 2. See Figure 1. Drill the rivets out of the backing plate (C) from the lower rear saddlebag hinge. •Enlarge the backing plate holes by drilling with a #19 drill bit. 3. Remove the rear isolator and install the new rear isolator (2) from the kit to the saddlebag. NOTE It is recommended to use Loctite® 262, threadlocker and sealant on the threads of the hinge screws. 4. See Figure 2 and Table 1. Position the backing plate (C) inside the saddlebag and align with the rear hinge (B) and hinge stop (3) on the outside of the saddlebag. Assemble using the two TORX® head screws (5). 2 1 is05974 1. Rear hinge rivets (2) 2. Rear isolator Figure 1. Drill Out Rivets From Rear Hinge and Backing Plate 5. Install the saddlebag to the motorcycle using the longer bail head stud (1) from the kit and a washer for the rear of the saddlebag and the washer and front bail head stud previously removed for the front of the saddlebag. 6. Repeat steps 1-5 for the opposite saddlebag

HARLEY DAVIDSON DYNA STATOR AND ROTOR KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 30-03-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Disconnect negative battery cable. See BATTERY MAINTENANCE in Service Manual. 2. Remove primary cover, primary drive, and clutch. See DRIVE COMPONENTS in Service Manual. 3. Remove primary chaincase according to the instructions in the Service Manual. 4. See Figure 2. Pull off the alternator rotor (1) using two bolts inserted through the holes in the rotor face. 5. Remove the two T-27 TORX screws (2). 6. Unplug the voltage regulator and remove the stator (3). See VOLTAGE REGULATOR in Service Manual. 7. Disassemble connector [46B] (A). See DEUTSCH ELECTRICAL CONNECTORS in Service Manual. NOTE Contact cleaner, alcohol, or glass cleaner sprayed on rubber grommet (B) will provide lubrication when pulling it through crankcase hole. 8. Move grommet (3) to one side and spray contact cleaner into gap. Repeat for other side. Pull rubber grommet (B) through crankcase hole. 9. Pull wires through crankcase hole. INSTALLATION 1. Insert wires through crankcase hole. 2. See Figure 1. Push rubber grommet (B) through crankcase hole. If necessary, apply the same lubricant used during removal. 3. Insert wires into connector [46B] (A). 4. Mate connector [46]. See VOLTAGE REGULATOR in Service Manual. is03776 Figure 1. Voltage Regulator 5. See Figure 2. Install the stator (3) on the crankcase and fasten in place using new TORX screws (2). Tighten to 55-75 in-lbs (6.2-8.4 Nm). 6. Install the rotor (1) on the sprocket shaft. 7. Apply Loctite Threadlocker 262 (red) to sprocket nut threads. Tighten sprocket nut to 150-165 ft-lbs (203.4- 223.7 Nm). 8. Install primary chaincase according to the instructions in the Service Manual. 9. Install clutch, primary drive, and primary cover. See DRIVE COMPONENTS in Service Manual. 10. Connect negative battery cable. See BATTERY MAINTENANCE in Service Manual

HARLEY DAVIDSON TIMKEN BEARING CONVERSION TOOL INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-03-2011

download
2-ton press (must be square to within .010″, ram to table) Inch-lb torque wrench Foot-lb torque wrench T15 TORX® drive socket (for inch-lb torque wrench) 5/32 inch hex drive socket (for inch-lb torque wrench) 5/16 inch hex drive socket (for foot-lb torque wrench) 5/64 inch hex key wrench 1/16 inch hex key wrench 3/8 inch drive hand drill small tap handle (suitable for #8-32 tap) Tapping Fluid Press Fit Lube (non-drip) Loctite® 620 threadlocker and sealant The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references service manual information. A service manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Kit Contents See Figure 21 and Table 3. If replacement parts are needed contact JIMS® at 805-482- 6913 or INSTALLATION 1. Remove and disassemble the engine as necessary to remove the left side engine case. Bearings and seals must be removed from the left case. Refer to the service manual for the disassembly procedures. 2. Use an appropriate solvent to clean the left engine case. Also clean the bearing sleeve (1) supplied in the kit. 3. Apply Loctite 620 to the smaller inside diameter portion of the left case bearing bore. 4. See Figure 1. Apply Loctite 620 using a cotton swab to the smaller portion of the outside diameter (2) surface of the bearing sleeve (1). 5. Apply a spare amount of non-drip press fit lube (3) to the larger outside diameter of the bearing sleeve. 6. See Figure 2. Fit the bottom locater plate (1) to the to the outside of the case over the bearing bore. The word “BOTTOM” will be at the bottom of the case when installed at the 6 o’clock position

Incoming search terms:

HARLEY DAVIDSON CHROME 1.25 INCH (31.75 MM) DIAMETER HANDLEBAR KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-03-2011

download
CHROME 1.25 INCH (31.75 MM) DIAMETER HANDLEBAR KIT GENERAL Kit Number 56032-08 Models For model fitment information, see the P&A retail catalog or the Parts and Accessories section of www.harley-davidson.com (English only). This kit does not fit models equipped with a hydraulic clutch, handlebar mounted gauges or the Road Tech® Radio. Additional Parts or Accessories Required Separate purchase of additional parts or accessories is required for proper installation of this Handlebar Kit on this model motorcycle. Please see the P&A retail catalog or the Parts and Accessories section of for a list of required parts or accessories for this model. For Australia, Brazil, England, Europe and Japan, two special screws (Part Number 2935A) will also be required. Tools and Supplies Required Loctite® 271 Threadlocker and Sealant – Red (H-D Part Number 99671-97) is required for the proper installation of this kit. Fresh, uncontaminated DOT 4 brake fluid from a sealed container will also be needed. Replace brake line gaskets. Re-using original gaskets can cause brake failure and loss of vehicle control, which could result in death or serious injury. (00318a) For models that retain the original brake line, the two brake- line gaskets found at each banjo fitting must be replaced . Refer to the appropriate parts catalog or see a Harley-Davidson dealer for the correct part numbers. Motorcycles equipped with a glued left-side hand grip will also require a new grip, sold separately. Refer to the parts catalog for replacement stock hand grips. Ask a Harley-Davidson dealer about the selection of Genuine Motor Accessory hand grips that are available. The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references service manual information. A service manual for this year and model motorcycle is required for this installation and is available from a Harley-Davidson dealer. Kit Contents See Figure 6 and Table 1. INSTALLATION Preparation To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Refer to the service manual and follow the instructions given to remove the seat and disconnect the battery cables, negative cable first. Retain all seat mounting hardware. Direct contact of D.O.T. 4 brake fluid with eyes can cause irritation. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 4 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00240a) D.O.T. 4 brake fluid will damage painted and body panel surfaces it comes in contact with. Always use caution and protect surfaces from spills whenever brake work is performed. Failure to comply can result in cosmetic damage. (00239b) NOTE Immediately wipe up any brake fluid spillage with a clean, dry, soft cloth. Follow up by thoroughly wiping affected area with a clean, damp, soft cloth (small spills) or washing with a large quantity of soapy water (large spills)

Incoming search terms:

1984-1999 HARLEY DAVIDSON Softails ULTIMA NARROW BODY ADJUSTABLE SOFTAIL SHOCKS MANUAL

0

Filed Under (Harley Davidson) by admin on 03-03-2011

download
Adjusting ride height Step 1. Loosen ride height adjusting locknut (see fig 1) Step 2. Loosen eyelet end to desired length/height (see fig 2) Step 3. IMPORTANT: Always verify that there are threads visible through the sight hole on the eyelet end. If adjusting with shocks installed on bike use a toothpick to verify that threads are blocking the sight hole. If threads are not visible turn eyelet end until they are visible. Failure to follow this step can result in failure. (see fig 3) Step 4. Once desired height is achieved check all clearances. Step 5. Using blue threadlocker lock down adjusting locknut to eyelet end. Step 6. Verify shocks are set at the same length. (See fig 4.)

HARLEY DAVIDSON SOFTAIL EXTENDED REACH CONTROLS KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 02-03-2011

download
PREPARE THE MOTORCYCLE 1. For models equipped with saddlebags: Remove the saddlebags following the instructions in the appropriate Service Manual. 2. Remove the seat following the directions in the Owner’s Manual. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 3. Disconnect the negative battery cable. 4. Secure motorcycle in upright position. NOTE This kit is not compatible with engine guards. 5. If the engine guard is present, remove and discard it. LEFT SIDE Component Removal 1 3 4 2 7 5 6 8 2 is05048 1. Pretzel clip 2. Bushing (2) 3. Screw (6) 4. Jiffy stand bracket 5. Bumper 6. Jiffy stand leg 7. Clevis pin 8. Spring Figure 1. Jiffy Stand 1 2 3 5 4 is05053 1. Jam nut 2. Shifter rod end 3. Acorn nut 4. Shifter rod 5. Shifter arm Figure 2. Shifter Linkage 1. For HDI Vehicles: Remove the left side foot control support, and jiffy stand sensor, jiffy stand and spring, shifter linkage, shift lever and footpeg following the instructions in the appropriate Service Manual. For all other models: Remove the left side foot control support, jiffy stand and spring, shifter linkage, shift lever and footpeg following the instructions in the appropriate Service Manual. NOTE Two bearing sleeves will remain inside the footrest bracket. The extended controls bracket from the kit will include two sleeves pressed into the bore of the shift lever arm support. 2. Remove rod ends and jam nuts from the shifter rod. Save the rod ends and jam nuts for installation. Component Installation 1. See Figure 9. Select shifter mounting assembly (6), O- rings (5), nylon washer (4) and the shift rod (1) from the kit. 2. Install the shift arm and new O-rings in the bracket. 3. Apply LOCTITE 243 Threadlocker and Sealant to the three mounting screws and mount the shifter bracket with shift arm to the frame. Tighten the mounting screws to 25-30 ft-lbs (33.9-40.7 Nm)

Incoming search terms:

HARLEY DAVIDSON FENDER SUPPORT COVER KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 25-02-2011

download
REMOVAL NOTE Complete all removal and installation procedures on one side before performing on the other side. 1. See Figure 1. Remove rear turn signal assembly (2) following the instructions in the service manual. Save all hardware for installation. 2. Remove the upper shock absorber hardware (3) following the instructions in the service manual. Save all hardware for installation. 3. Remove the rear fender support cover (4) following the instructions in the service manual. Save all hardware for installation. INSTALLATION 1. See Figure 1. Install the rear fender support cover (4) with the stock hardware. Tighten finger-tight. 2. Install the rear turn signal assembly (2) following the instructions in the service manual. 3. Install the upper shock absorber hardware (3) following the instructions in the service manual. 4. Remove the rear fender support cover hardware and apply Loctite Threadlocker and Sealant 243 (Blue) to the threads of the screws. Tighten screws to the specifications in the service manual. 5. Thoroughly clean the mounting surface of the fender support cover with an equal mixture of water and isopropyl alcohol. Peel the paper backing from the new reflector and install reflector (1). Press the reflector firmly. Allow AT LEAST 24 hours after applying the reflectors before exposing the areas to vigorous washing, strong water spray or extreme weather

HARLEY DAVIDSON CHROME REAR WHEEL KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 19-02-2011

download
Kits 41017-00, 41026-00 and 41262-03 are designed for installation on 2000 and later XL, FXD and 2000-2002 Softail Model Motorcycles (except FXSTD and FLSTS). Kits 41260-03, 41261-03 and 41265-03 are designed for installation on 2003 and later Softail Model Motorcycles (except FXSTD and FLSTS). Kit Numbers 41017-00 and 41261-03 contain a16 inch chrome slotted rear wheel. Kit Numbers 41026-00 and 41260-03 contain a 16 inch chrome fatboy rear wheel. Kit Numbers 41262-03 and 41265-03 contain a 16 inch mirror chrome disc rear wheel. See Service Parts Illustration for kit contents. nstallation Do not re-use brake disc screws. New screws are provided for disc installation. Re-using original disc screws can result in torque loss and damage to rotor and/ or brake assembly. (00319a) Refer to the appropriate Service Manual for wheel removal and installation procedures. See Service Parts Illustration. This kit contains the necessary parts for wheel installation, however you will need to save the Axle, Axle Nut, Brake Disc, and the Drive Pulley with related hardware for reinstallation. NOTE The cotter pin or spring clip for the axle nut must be replaced. They are available for purchase from your dealer. See your dealer for the correct part number for your model motorcycle. NOTE Apply two drops of LOCTITE THREADLOCKER 262 (red) to each of the five sprocket mounting screws. Follow the bolt torque procedure in your service manual or, if installing an accessory hardware kit, in the I-sheet included with the hardware kit. Maintenance and Cleaning Chrome parts must be maintained regularly to ensure that they keep their original shine and luster. 1. Clean heavily-soiled wheel surfaces using Harley Wheel & Tire Cleaner Part Number 94658-98 applied with Harley Wheel & Spoke Brush Part Number 43078-99. 2. Thoroughly clean chrome with a good quality chrome cleaner, such as Harley Bright Chrome Cleaner Part Number 94683-99. 3. After cleaning and polishing, seal the finish with a good quality sealer such as Harley Glaze Polish and Sealant, Part Number 99701-84

HARLEY DAVIDSON FOUR-POINT DETACHABLE DOCKING HARDWARE KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-02-2011

download
INSTALLATION 1. See Figure 3. Remove the screw (A) retaining the rear of the chrome cover to the rear frame extension on each side of the vehicle. 2. Place a washer (7) over the threads of each of the larger TORX® head screws (6) from the kit. Apply 2 or 3 drops of Loctite 262 Threadlocker and Sealant – Red to the threads of each screw. Install the screws through the docking plates (1) and fender covers, and into the threaded holes in the frame extensions on each side of the vehicle, and tighten to 17 ft-lbs (23 Nm) . NOTE See Figure 1. The docking points must be attached to the docking plates (2) with the chamfer (1) facing the plate and the flat side facing out. 1 2 is05506a 1. Docking point chamfer (bevel) 2. Mounting plate Figure 1. Docking Point Installation 3. See Figure 3. Slide a spacer (2) onto the longer pin (B) of each docking plate. Install the four docking points (3), chamfer end first, onto the long and short docking plate pins using the washers (5) and smaller TORX screws (4). Tighten to 10.5 ft-lbs (14.2 Nm) . NOTE Protective tape must be installed to the rear saddlebag mounting bracket to prevent damage to the saddlebag finish when the lid is opened. 4. See Figure 2. Apply protective tape (2) to the rear mounting bracket (1) on the saddlebag in the location shown. Repeat for the other side. 2 1 is05533 1. Rear saddlebag bracket (2) 2. Protective tape %lengthT=0