KAWASAKI 1500 9408 PRO HYPERCHARGER INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 26-04-2012

download
STEP 1 Remove the seat STEP 2 Disconnect the battery positive cable to prevent sparking that could cause ignition of spilled fuel, and personal injury. STEP 3 Remove the fuel tank. IMPORTANT- Throughout this installation, we strongly recommend labeling all hoses, and the nipples they were removed from. STEP 4 Remove the intake ductwork, air inlet, right and left air cleaner housings, air cleaner, cold start components (see PIC. 1), air mass sensor, and support bracketry. The wires that were unplugged from the cold start solenoids, may be neatly bundled and tucked out of harms way and out of sight. Be sure the terminals are insulated so they cannot short to any surrounding parts. Insert plugs (3/8″ x 1/2″ socket head bolts work well) into the two hoses that connected to the cold start circuit lines. (See PIC.2.) Also unplug the crankcase breather hose from the right angle fitting at the bottom of this enclosure, and the large diameter hose from the fresh air injection valve. (Don’t forget to label.) The fuel drain hose will not be re-used. PIC.3 shows what you’ll have left when all components are removed. STEP 5 From the hardware kit, find the front and rear support tabs and the four M6 x 1.0 x 16mm socket head cap screws. Install the support tabs to the threaded holes in each cylinder, and to the holes in the throttle body as shown in PIC.4. STEP 6 From the hardware kit, find the M6 x 1.0 x 16mm hex bolt and lock tab washer. Also find the intake gasket (oval shape with two large holes) and the manifold adapter body. See PIC.5. Screw the air temperature sensor into the back of the manifold adapter body. Place the intake gasket over the mouth of the throttle body so all holes line up. Insert the M6 hex bolt through the lock tab washer, and secure the adapter body to the throttle body, again making certain all holes line up perfectly. Tighten the hex bolt, but do not bend the lock tabs yet

1997-1998 Harley-Davidson Evo FI controller installation manual

0

Filed Under (Harley Davidson) by admin on 25-03-2012

download
Remove the seat. Remove or raise the fuel tank. The tank needs to be raised enough to give access to the fuel injectors and TPS wires. Unplug the front injector. On the FI Controller, there are 2 pairs of injector connectors. Plug the pair with the orange wires into the front cylinder injector harness and front cylinder injector. Repeat this using the other connector pair and the rear cylinder injector. Locate the TPS connector behind the throttle body. STEP 1 STEP3 STEP2 Installation Part# DFCH-1 2 Rear Cylinder Injector Front Cylinder Injector TPS Connector STEP 3 STEP 2 STEP1 Unplug the connector from the TPS. Crimp the wire tap onto the wire that is grey with a purple stripe. This wire should be in position “C” on the connector. Plug the grey wire from the FI Controller into the wire tap. Run the wiring harness for the FI Controller from the engine to the seat. Make sure that it will not get damaged when you reinstall the tank. Use one of the wire ties to tie the wires to the frame, away from the cylinder head. Place the FI Controller where you plan on mounting it permanently. In most cases, this will be under the seat. Connect the ground lug (black wire) to a grounding point on the bike. Use the Velcro tape to mount the FI Controller in position. Use alcohol swab to clean mounting surface prior to attaching Velcro. Reinstall fuel tank and seat

SUZUKI GSX-R1300 / HAYABUSA Fuelpak Connectors INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 15-02-2012

download
Remove the main seat and passenger seat. 2. Use a prop to hold the tank up in the trunk area. 3. Disconnect the main wiring harness from each of the lower injectors. (Fig 1) 4. Lay the Fuelpak unit in the tail section and route the wire harness down the left side of the motorcycle toward the throttle bodies. 5. Plug the Fuelpak wiring harness in line of the stock wiring harness and injectors. (Fig 2) 6. Locate the throttle position sensor connector on the right hand side of the throttle body. 7. Install the Fuelpak wiring harness TPS connectors in line of the stock wiring harness. (Fig 3) 8. Attach ground wire to the negative side of the battery. 9. Install Fuelpak in the tail section using the supplied velcro. (Fig 4) 10. Bolt the fuel tank back into place. INSTALLATION INSTRUCTIONS FOR P/N 62009 READ ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION FUEL INJECTION

Toyota 2006-10 Yaris L4-1.5L NTAKE TUBE, THROTTLE BODY AND ENGINE REMOVAL AND INSTALLATION

0

Filed Under (Toyota Manuals) by admin on 26-09-2011

download
turn the ignition OFF and disconnect the vehicle’s negative battery cable. NOTE: FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS AND NOT USING THE PROVIDED HARDWARE MAY DAMAGE THE INTAKE TUBE, THROTTLE BODY AND ENGINE. 2. Depress the locking tab and remove the mass air sensor connector. Remove the clips that secure the mass air sensor har- ness to the stock air box. 3. Pull the vacuum switching valve and bracket assembly from the stock intake tube. Un-clip the vacuum hose from the stock intake tube. 4. Loosen the spring clamp that secures
the crank case vent tube to the stock intake tube as shown. Remove the crank case vent tube from the stock intake tube. Note: The spring clamp will be re-used. 5. Loosen the hose clamp that secures the stock intake tube to the throttle body as shown. Remove the stock intake tube from the throttle body

Toyota Camry 2006 clean engine

0

Filed Under (Toyota Manuals) by admin on 01-06-2011

Download
Why clean the throttle body on your Toyota? The Toyota 4 cylinder engine is one of the best in the world, but it has one weak spot. The design of the P.C.V. system is such that blow-by gases get into the throttle body and butterfly area. Over time, after 30,000 miles or more, the build-up of crud caused by this can cause your engine to run wrong. Many people wind up taking their car to the shop and spending lots of money to fix a rough-running, hard-starting engine when all they need is some rags, a screwdriver, and $5 for a can of throttle body cleaner (or a little more for a can of Seafoam) and 20 minutes worth of time to clean inside their throttle body. This article tells you how

SUZUKI SV1000 PERIODIC MAINTENANCE

0

Filed Under (Suzuki) by admin on 26-02-2011

download
MAINTENANCE AND TUNE-UP PRO- CEDURES This section describes the servicing procedures for each item of the Periodic Maintenance requirements. AIR CLEANER I Inspect every 6 000 km (4 000 miles, 6 months) and replace every 18 000 km (11 000 miles, 18 months) . • * Remove the seat. (LF6-7) • * Lift and support the feul tank . (C-74-65) • * Remove the air cleaner box cap O. • * Remove the air cleaner element O. • * Carefully use air hose to blow the dust from the cleaner ele- ment. CAUTION Always use air pressure on the throttle body side of the air cleaner element . If air pressure is used on the other side, dirt will be forced into the pores of the air cleaner element thus restricting air flow through the air cleaner element . PERIODIC MAINTENANCE 2-5 2-6PERIODIC MAINTENANCE • * Reinstall the cleaned or new air cleaner element in the reverse order of removal . CAUTION If driving under dusty condition, clean the air cleaner element more frequently. The surest way to accelerate engine wear is to use the engine without the element or to use a ruptured element. Make sure that the air cleaner is in good condition at all times. Life of the engine depends largely on this component! NOTE: When cleaning the air cleaner element, drain water from the air cleaner by removing the drain plug . SPARK PLUG Inspect every 6 000 km (4 000 miles, 6 months) and replace every 12 000 km (7 500 miles, 12 months) . No. 1 (FRONT) SPARK PLUG REMOVAL • * Remove the radiator mounting bolt O. • * Move the radiator forward. • * Remove the spark plug cap O. NOTE: Be careful not to damage the radiator fins . A WARNING The hot radiator and the hot engine can burn you . Wait until the radiator and the engine are cool enough to touch . • * Remove the spark plug with a spark plug wrench. 1 6 I It No. 2 (REAR) SPARK PLUG REMOVAL • * Remove the seat. (r–,-6-7) • * Lift and support the fuel tank . (=4-65) 4-65) • * Disconnect the camshaft position sensor 1O and breather hose (Z. • * Remove the rubber heat shield ® . • * Remove the spark plug cap . • * Remove the spark plug with a spark plug wrench . HEAT RANGE • * Check to see the heat range of the plug . CARBON DEPOSIT •Check to see if there are carbon deposits on the plugs . If carbon is deposited, remove it with a spark plug cleaner machine or carefully using a tool with a pointed end . SPARK PLUG GAP • * Measure the plug gap with a thickness gauge . If out of specification, adjust it to the following gap . 09900-20803 : Thickness gauge Spark plug gap OA Standard: 0.6 – 0 .7 mm (0.024 -0.028 in) ELECTRODES CONDITION •Check to see the worn or burnt condition of the electrodes . If it is extremely worn or burnt, replace the plug . And also replace the plug if it has a broken insulator, damaged thread . CAUTION Confirm the thread size and reach when replacing the plug. If the reach is too short, carbon will be deposited on the screw portion of the plug hole and engine damage may result

Incoming search terms:

2003 SUZUKI SV 650 FUEL SYSTEM AND THROTTLE BODY SERVICE MANUAL

0

Filed Under (Suzuki) by admin on 26-02-2011

download
FUEL PUMP The electric fuel pump is mounted at the bottom of the fuel tank, which consists of the armature, magnet, impeller, brush, check valve and relief valve . The ECM controls its ON/OFF operation as controlled under the FUEL PUMP CONTROL SYSTEM . When electrical energy is supplied to the fuel pump, the motor in the pump runs and together with the impel- ler . This causes a pressure difference to occur on both sides of the impeller as there are many grooves around it . Then the fuel is drawn through the inlet port, and with its pressure increased, it is discharged through the outlet port . The fuel pump has a check valve to keep some pressure in the fuel feed hose even when the fuel pump is stopped . Also, the relief valve is equipped in the fuel pump, which releases pressurized fuel to the fuel tank when the outlet of the fuel pressure has increased up to 450 -600 kPa (4.5- 6.0 kgf/cm2,64- 85 psi) . Relief valve Brush , ∎ I,’ Check valve Magnet L Armature When the impeller is driven by the motor, pressure differential occurs between the front part and the rear part of the blade groove as viewed in angular direction due to fluid friction . This process continuously takes place causing fuel pressure to be built up . The pressurized fuel is then let out from the pump chamber and discharged through the motor section and the check valve . FUEL SYSTEM AND THROTTLE BODY 5- 3 Inlet port I I Impeller 5-4 FUEL SYSTEM AND THROTTLE BODY FUEL PRESSURE REGULATOR The fuel pressure regulator consists of the spring and valve . It keeps absolute fuel pressure of 300 kPa (3.0 kgf/cm2,43 psi) to be applied to the injector at all times . When the fuel pressure rises more than 300 kPa (3 .0 kgf/cm2, 43 psi), the fuel pushes the valve in the regulator open and excess fuel returns to the fuel tank . 90 Spring 02 Valve FUEL INJECTOR The fuel injector consists of the solenoid coil, plunger, needle valve and filter . It is an electromagnetic type injection nozzle which injects fuel in the throttle body according to the signal from the ECM. When the solenoid coil of the injector is energized by the ECM, it becomes an electromagnet and attracts the plunger. At the same time, the needle valve incorporated with the plunger opens and the injector which is under the fuel pressure injects fuel in conic dispersion . As the lift stroke of the needle valve of the injector is set constant, the volume of the fuel injected at one time is determined by the length of time during which the solenoid coil is energized (injection time)

Incoming search terms:

Kawasaki KX250F Factory Tuning And Fuel Injection to keep expert riders at the front of the pack

0

Filed Under (Kawasaki) by admin on 08-02-2011

download
Battery-less fuel injection system Designed specifically for motocrossers, the fuel injection system incorporates a small lightweight ECU and operates without a battery to further eliminate unnecessary weight. And of course, fuel injection eliminates the need to adjust engine settings to suit track and climate conditions. Ensuring quick starting without a battery was a prime directive when developing this fuel injection system. Using only electricity generated by the kick starter, the engine can be started with only three rotations of the crankshaft. The system delivers electricity in the following order:1) ECU, 2) fuel pump, 3) injector. With a warm engine, starting can be accomplished in a single kick. The compact, lightweight ECU, located just in front of the steering head (behind the number plate), was designed specifically for motocross use. To help cope with the shocks and vibrations of motocross riding, the fuel pump relay is built into the ECU. A 43 mm throttle body makes use of a progressive throttle link to deliver airflow in much the same way as would a FCR carburettor. Using two linked shafts, the throttle body opens more quickly after the 3/8 open position, delivering sharp response and excellent power. Lightweight throttle body is approximately half the weight of a FCR carburettor – a weight savings of about 600 g. To ensure the high-rpm engine’s demand for a high flow of fuel in a short period is met, the KX250F’s injector features larger holes than that used on the KX450F. A fine atomising injector with 4 holes disperses spray particles with a droplet size of 120 µm. Fuel flow is about 20% greater than on the KX450F. The newly designed fuel pump, located in the fuel tank, is a lightweight aluminium construction. (Fuel tank capacity is now 7.2 litres.)

Incoming search terms:

DRAK AIR FILTER KIT INSTALLATION MANUAL

0

Filed Under (Tips and Review) by admin on 21-12-2010

download
1. Take off the Air fi lter cover by removing the Button head cap screw in the center. 2. Removed the fi lter element by taking out the three exposed Torx head cap screws. 3. Remove the breather hoses from the Cylinder head breather bolts by pulling on them. 4. Remove the three Bolts that secure the Backing plate to the Carburetor / Throttle body and the two Breather bolts that secure it to the Cylinder heads. 5. Remove the Backing plate and Gasket, on FI models the wiring mount clip should be carefully pulled out of the plastic housing. NOTE: Be sure that the gasket surface is clean and dry and that no gasket material remains stuck to it. 6. None of the OEM parts will be reused for this installation 1. For a clear understanding of this installation it is best to refer to the exploded view diagram while reading these instructions. 2. When installing or servicing the air cleaner, apply Loctite 243 (blue) to threads of all fasteners. 3. Loosely install the gasket (1) and carburetor / throttle body mount bracket (2) using the two cylinder head breather bolts (3) and cylinder head O-rings (4) NOTE: Make sure the gasket is installed in the correct rotation and right side up. The slightly smaller bleed hole should be in the top left hand corner. 4. Using the three 1/4″-20 x 1″ socket head cap screws (5) install the fi lter backing

SUZUKI VZR1800K6 And VZR1800/ ZK7 FUEL DELIVERY PIPE REPLACEMENT

0

Filed Under (Suzuki) by admin on 26-11-2010

download
NOTE: The fuel delivery pipe assembly can be removed from the throttle body without removing the throttle body assembly from the motorcycle. 1) Refer to section 6 of the service manual to remove the fuel tank and the air cleaner box. Place shop rags over the bore of each throttle body to prevent anything from falling into the engine through the throttle bodies. 2) Remove the wire harness clamp, disconnect the fuel injector couplers A and move the harness aside. 3) Remove the four fuel delivery pipe assembly mounting screws and remove the fuel delivery pipe assembly. 4) Replace the o-rings and seals with the new parts supplied in the kit (apply a small amount of engine oil to the o-rings and seals to ease the installation of the injector). To prevent damage to the o-rings or seals, don’t turn the injector when pushing it into the fuel delivery pipe and throttle body respectively. Install the new fuel delivery pipe assembly in the reverse order of removal. 5) Connect the fuel injector couplers A and clamp the injector harness to the fuel delivery pipe. DO NOT overtighten the harness clamp. 6) Connect the fuel tank, remove the shop rags from over the bore of each throttle body, and run the engine, checking for fuel leaks. DO NOT reuse the original fuel hose connector retainer. Confirm that the fuel hose connector has completely seated and locked (clicked) into position before turning on the ignition switch. 7) Refer to section 6 of the service manual to install the air cleaner box and the fuel tank. 8) Test ride the motorcycle to confirm proper operation. FUEL DELIVERY PIPE ASSEMBLY REPLACEMENT PROCEDURE

Incoming search terms: