HARLEY DAVIDSON BIG TWIN SPIGET MOUNT CARBURETOR INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 26-03-2012

download
A. BEFORE INSTALLATION OF YOUR NEW ZENITH CARBURETOR, NSPECT THE RUBBER MANIFOLD SEAL FOR NICKS,CRACKS, OR DEBRIS. APPLYING A LIGHT FILM OF PETROLEUM BASED LUBRICANT AROUND THE INSIDE LIP OF THE RUBBER SEAL WILL ALLOW THE CARBURETOR TO SLIP INTO PLACE EASIER. B. BEFORE ACTUAL INSTALLATION OF UNIT INTO MANIFOLD, THROTTLE CABLES SHOULD BE HOOKED TO THETHROTTLEWHEEL.MAKESURETHATTHE PULL CABLE IS LOCATEDPROPERLY TO OPEN THE THROTTLE PLATE (IN SOME APPLICATIONS THROTTLE CABLE SLACK MAY NEED TO BE ADJUSTED FOR PROPER HOOKUP AND OPERATION) SEE FIG. #1 C. AFTER THROTTLE CABLES ARE PROPERLY HOOKED UP,UNITCAN BE INSERTED INTO MANIFOLD. MAKE SURE THAT UNIT IS FULLY SEATED. WITH CARBURETOR SEATED INTO MANIFOLD AND FUEL LINE HOOKED UP TO FUEL INLET, INSTALL CHOKE CABLE AND HOOK TO CHOKE LEVER. PLACE AIR INTAKE GASKET ON END OF CARBURETOR, NEXT PLACE INTAKE ADAPTOR OVER INTAKE GASKET. SEE FIG#2 ZENITH MOD.16P12 SPIGET MOUNT CARBURETOR -HARLEY DAVIDSON ™ BIG TWIN INSTALLATION INSTRUCTIONS FIG. # 1 FIG. # 2 D. WITH ADAPTOR IN PLACE, LOCATE THE STOCK AIR BOX OVER THE ADAPTOR, UTILIZING THE STOCK AIR BOX GASKET (THERESHOULDBENO GAPS BETWEEN ADAPTOR, AIRBOX OR CARBURETOR WHEN PROPERLY INSTALLED) STAND-OFF SPACERS PROVIDED ARE TOBEPLACEDBETWEENAIR BOX& ENGINE HEADS BEFORE INSTALLING THE VENT/RETAINING BOLTS. FOR EVALUATION ENGINES STOCK VENT BOLTS CAN BE USED WITH LARGERI.D. SPACER PROVIDED. SEE FIG#3 E. WITH AIR BOXSECURELY IN PLACE, INSTALL THE AIR FILTER COVER RETAINING BRACKET AND FILTER USING THE STOCKBOLTS, AND REPLACE AIR FILTER COVER AND SECURE WITH STOCK BOLT. SEE FIG#4 F. AFTER INSTALLATION IS COMPLETE AND FUEL FLOW HAS BEEN RE-ESTABLISHED, CHECK FOR ANY LEAKS BEFORE STARTING ENGINE. H. AFTER STARTING ENGINE, SOME ADJUSTMENTS OF IDLE AND MAIN JET MAYBE REQUIRED FOR PROPER OPERATION. AFTER ADJUSTMENTS HAVE BEEN MADE AND WITH ENGINEAT IDLE, TURN WHEEL FULLYTOLEFTANDRIGHT.ANYCHANGEIN IDLE SPEED INDICATES THROTTLE CABLES ARE TOO TIGHT AND MORE SLACK MUST BE PROVIDED.

Incoming search terms:

YAMAHA YFM 350 Removing stock carburetor and cables.

0

Filed Under (Yamaha) by admin on 19-01-2012

download
Remove seat and gas tank. Make sure fuel petcock is in “off” position. 2. Remove throttle cable paying close attention to routing, as the new cable (s) will need too be routed the same. 3. Remove stock carburetor and stock throttle housing. Preparing motor for carburetor install 1. Remove stock manifold from cylinder head. 2. Place supplied o’ring into aluminum flange as pictured in figure 1. Figure 1. 3. Install aluminum and rubber flange to motor using supplied bolts. See Figure 2. The shorter 25mm bolt will need to be placed in the bottom hole. IMPORTANT NOTE: Install the aluminum flange with the o’ring towards the motor and the thick side up.

YAMAHA RAPTOR 350 Removing stock carburetor and cables

0

Filed Under (Yamaha) by admin on 18-01-2012

download
remove seat and gas tank. Make sure fuel petcock is in “off” position. 2. Remove throttle cable paying close attention to routing, as the new cable (s) will need too be routed the same. 3. Remove stock carburetor and stock throttle housing. Stuff a clean, dry rag into manifold to keep debris out of motor. 4. Remove stock air box. 5. Remove choke cable from handlebars. 6. Remove carb vent line from bike. Carburetor installation 1. Carefully trim the rubber alignment tab off of the face of the manifold with a razor blade or side cutters. 2. Remove the hex pipe plug from the carb cap using a 11mm or 7/16 wrench. Do not discard plug, as it will be needed later. Install the metering adjustment tool included in the hardware kit. Do not over-tighten as damage may occur to cap. 3. Attach fuel line to carburetor and secure with clamp. 4. Install remote idle cable into tab on top of carburetor. See main manual for this step. NOTE: Nut must be removed from cable before installation 5. Place carburetor into manifold

Incoming search terms:

Yamaha XV-1900 Braided Stainless Steel Thottle Cables Installation Instructions

0

Filed Under (Yamaha) by admin on 30-12-2011

download
Please read and understand these instructions completely before installation to avoid injury or damage to the motorcycle or accessory. IMPORTANT: Dealer installation is recommended. The installer should have the service manual for the motorcycle , as well as a good understanding of motorcycle service and repair techniques. Dealer: These instructions contain important information for future reference and must be given to the customer. 1. Parts List: Item Part Name Part Number Description Qty 1 Throttle Cable Set 07-1083 1 2. Preparation: a) Before installation, lubricate cable with an appropriate cable lube such as Motion Pro Cable Lubricant (P/N 15-0002) b) Securely place motorcycle on side stand 3. Installation: Refer to vehicle service manual for installation instruction and adjustment procedures. NOTE: Notice how original cable routed before removing it. Install the accessory cable in the same way. If unsure or original cable routing, refer to the cable routing diagram in the service manual. WARNING ∞ Before starting the engine, be sure the throttle operates smoothly and check that throttle body is fully closed when throttle is released ∞ After starting the engine, turn the handlebar to the right and to the left to be sure the throttle operation is not affected ∞ Improper installation could result in great bodily injury or death 4. Maintenance: Check throttle operation before each ride. Follow Periodic Maintenance procedures in the owner’s manual for adjustment and lubrication. 5. Care and Cleaning: See your Owner’s Manual

YAMAHA RX10H/ RX10SH RX10MH/ RX10MSH/ RX10RH/ RX10RSH SERVICE AND OWNER’S MANUAL

0

Filed Under (Yamaha) by admin on 27-04-2011

download
Throttle override system (T.O.R.S.) If the carburetor or throttle cable should malfunction during operation, the T.O.R.S. will operate when the throttle lever is released. The T.O.R.S. is designed to interrupt the ignition and keep the engine revolution speed between 2,800 and 3,000 r/min if the carburetor fails to return to idle when the lever is released. Speedometer unit The speedometer unit is equipped with the following: a digital speedometer (which shows riding speed) an odometer (which shows the total distance traveled) a tripmeter (which shows the distance traveled since it was last set to zero) warning indicators (which show self-diagnosis, cool ant temperature, fuel level, and oil level warnings) fuel meter (which shows the fuel remaining in the fuel tank) grip/thumb warmer heat level indicator  (which shows the heat level of the grip warmer or the thumb warmer) After the engine is started, the tachometer 1 makes one sweep, and the warning light 2 and all segments of the meter 3 turn on and off once. Then the warning light turns on again, and then goes off if there are no problems. The grip warmer heat level is initially displayed for 5 seconds, then switches to the fuel meter display. Odometer and tripmeter modes Pushing the select/reset button 4 switches the display between the odometer mode “ODO” and the tripmeter mode “TRIP”. To reset the tripmeter, push the select/reset button for at least one second while the tripmeter is displayed. NOTE: @ To switch the speedometer, odometer, and tripmeter displays between kilometers and miles, select the odometer mode “ODO”, and then push the select/reset button 4 for at least 10 seconds. ESU00363 High beam indicator light The high beam indicator light 1  comes on when the high beams of the headlights are switched on. (See page 5-12 for headlight beam switch operation.)

Incoming search terms:

Yamaha TW200N/ TW200NC SPECIFICATIONS AND SUPPLEMENTARY SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 26-04-2011

download
GENERAL INFORMATION MOTORCYCLE IDENTIFICATION EAS00017 VEHICLE IDENTIFICATION NUMBER The vehicle identification number 1 is stamped into the right side of the steering head pipe. EAS00018 MODEL CODE The model code label 1 is affixed to the frame. This information will be needed to order spare parts CABLE ROUTING 1 Throttle cable 2 Front brake light switch lead 3 Right handlebar switch lead 4 Clutch cable 5 Left handlebar switch lead 6 Clutch switch lead 7 Front turn signal/position light lead (left) 8 Main switch lead 9 Indicator lights lead 0  Speedometer cable A Meter light lead B Headlight coupler C Wire harness D Front turn signal/position light lead (right) E Brake hose ب Fasten the brake hose with a plastic locking tie to the brake hose grommet. ة Fasten the wire harness with a plastic locking tie PERIODIC CHECKS AND ADJUSTMENTS INTRODUCTION This chapter includes all information necessary to perform recommended checks and abjustments.If followed, these preventive maintenance procedures will ensure more reliable vehicle operation, a longer service life and reduce the need for costly overhaul work.This information applies to vehicles already in service as well as to new vehicles that are being prepared for sale.All service technicians should be familiar with this entire chapter. PERIODIC MAINTENANCE CHART FOR EMISSION CONTROL SYSTEM

HARLEY DAVIDSON MULTI-FIT BRAIDED THROTTLE/IDLE CABLE KITS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-03-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Disconnect battery cables, negative (-) cable first or remove the main fuse following the instructions in the service manual. NOTE When performing cable disassembly procedures, make careful notes as to the existing cable routing. Pay special attention to existing cable strap locations before removing so new straps can be installed in the same locations. Do not remove or install the master cylinder assembly without first positioning a 5/32-inch (4 mm) thick insert between the brake lever and lever bracket. Removing or installing the master cylinder assembly without the insert in place may result in damage to the rubber boot and plunger on the front stoplight switch. (00324a) 2. See Figure 1. Place the cardboard insert between the brake lever and lever bracket. 3 2 1 is00825 1. Brake lever 2.5/32 inch (4 mm) cardboard insert 3. Brake lever bracket Figure 1. Install Cardboard Insert 3. See Figure 2. Loosen cable adjuster jam nuts. Turn cable adjusters in until they are as short as possible. This will provide enough slack for easy removal. 3 4 1 2 5 is 02071 1. Upper switch housing 2. Lower switch housing 3. Throttle cable adjuster 4. Idle cable adjuster 5. Adjuster jam nut Figure 2. Handlebar Throttle Control 4. Remove the right upper and lower switch housing screws. 5. Loosen the upper screw securing the handlebar clamp to the master cylinder housing. Remove the lower clamp screw and flat washer. NOTE If possible, leave the friction shoe in place. The friction shoe is a loose-fit and may fall out or become dislodged if the lower switch housing is turned upside down or shaken. 6. See Figure 3. Remove the brass ferrules from the notches on the inboard side of the throttle control grip. Remove the ferrules from the cable end fittings. 1 2 4 3 is 02072 1. Throttle cable 2. Idle cable 3. Brass ferrule 4. Notch Figure 3. Throttle/Idle Control Cables 7. Pull the crimped inserts at the end of the throttle and idle control cable housings from the lower switch housing. For best results, use a rocking motion while pulling. Remove cables with retaining rings from switch housing. Apply a drop of light oil on the retaining ring, if necessary, to help in removal. NOTE If installing different handlebars, measure the change in distance that will be required from the end of the cable housing to the throttle grip. Compare this additional required length to the cables provided in the kit. If the cables are more than 2.0 inches (51 mm) longer or more than 1.0 inch (25 mm) shorter than the above measured distance, see a Harley-Davidson dealer for the correct cable length. Install proper length throttle cables. Incorrect cable length can adversely affect motorcycle operation, which could cause loss of control resulting in death or serious injury. (00396b) 8. Follow instructions in the applicable service manual and remove air cleaner and backplate.

Incoming search terms:

SUZUKI SV650/ S PERIODIC MAINTENANCE CHART

0

Filed Under (Suzuki) by admin on 26-02-2011

download
Item km miles months 1000 6000 12000 18000 24000 600 4000 7500 11000 15000 1 6 12 18 24 Air cleaner Spark plugs Tappet clearance Engine oil Engine oil filter Fuel hose Engine idle speed Carburettor synchronization Evaporative emission control system PAIR air supply system Throttle cable play Clutch cable play Radiator hoses Engine coolant Drive chain Brakes Brake hoses Brake fluid Tires Steering Front forks Rear suspension Exhaust pipe bolt & nut Chassis bolt & nuts – - – R R – I I I – - I I – - – I – - T T Replace every 4 years Replace vapor hose every 4 years – - I – I I I – - Replace every 2 years Clean & lubricate every 600 miles (1000km) Replace every 4 years Replace every 2 years R R R R – - R – I I R I I R I R – Inspect and adjust, clean

HARLEY DAVIDSON MULTI-FIT BRAIDED THROTTLE/ IDLE CABLE KITS REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 01-02-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Disconnect battery cables, negative (-) cable first or remove the main fuse following the instructions in the service manual. NOTE When performing cable disassembly procedures, make careful notes as to the existing cable routing. Pay special attention to existing cable strap locations before removing so new straps can be placed into the same locations. Do not remove or install the master cylinder assembly without first positioning a 5/32-inch (4 mm) thick insert between the brake lever and lever bracket. Removing or installing the master cylinder assembly without the insert in place may result in damage to the rubber boot and plunger on the front stoplight switch. (00324a) 2. See Figure 1. Place the cardboard insert between the brake lever and lever bracket. 3. See Figure 2. Loosen cable adjuster jam nuts. Turn cable adjusters in until they are as short as possible. This will provide enough slack for easy removal. 4. Remove the right upper and lower switch housing screws INSTALLATION Throttle and Idle Cable Installation 1. See Figure 3. Apply graphite lightly to the throttle grip inside the switch housing and on the throttle end of the handlebar. NOTE The throttle control cable has a larger diameter retaining ring crimped to the cable end than does the idle control cable. For assembly, apply a drop of light oil on the retaining rings of the crimped inserts. 2. See Figure 7. Push the throttle cable housing and retaining ring into the larger hole of the switch housing, located in front of the tension adjuster screw. 3. Push the idle cable housing and retaining ring into the smaller hole of the switch housing, located behind the tension adjuster screw. 4. Push the throttle and idle control cable housings into the lower switch housing until each snaps into place. NOTE For models not equipped with factory-installed cruise control, if the friction shoe has fallen out or become dislodged, install the shoe with the concave side facing up and position it so the pin hole is over the point of the adjuster screw. 5. Push the throttle control grip over the end of the right handlebar until it bottoms against the closed end. Rotate the grip until the ferrule notches are at the top. To prevent binding, pull the grip back about 0.12 inch (3.2 mm). 6. See Figure 3. Position the lower switch housing beneath the throttle control grip. Install two brass ferrules (Item 3, Figure 11) from this kit onto cables, seating the ferrules in their respective notches on the throttle control grip. The cables must be captured in the grooves molded into the grip. 7. Position the upper switch housing over the handlebar and lower switch housing. Route the wire harness conduit through the depression at the bottom of the handlebar. 8. Tighten the upper and lower switch housing screws finger- tight. 9. Position the brake lever/master cylinder assembly inboard of the switch housing assembly, engaging the tab on the lower switch housing in the groove at the top of the brake lever bracket. 10. Align the holes in the handlebar clamp with those in the master cylinder housing and tighten the lower screw and flat washer finger-tight. Position for rider comfort. Beginning with the top screw, tighten the screws to 60-80 in-lbs (6.8-9.0 Nm)

ROKON Illustrated Owners and Parts Manual

0

Filed Under (Rokon) by admin on 28-11-2010

download
Front and Rear Brake. Check brake action. Check pucks to see that they are not over worn. There should be visible brake material on both sides of the brake disc. See Section 6. Fuel Tank. Check fuel level. Fill as necessary. Use super unleaded for altitudes above 10,000 ft. Engine Oil. The engine holds .6 qt. of SAE10W30/40 motor oil. Fill to the dipstick “full” line. Miter Box and Transmission. They are fi lled at the factory and need not be checked at the start. The miter box should have 2.5 oz. of EP 80W90 gear lube oil. The transmission takes 6 oz. of EP 80W90 gear lube oil. The transmission has a fi ll to plug near the bottom of the transmission( shown on page 46). There is no fi ll level for the miter box. Over fi lling of either the miter box or transmission will result in leakage. Throttle. Check for proper throttle cable operation. Look for smooth response to twist action. Wheels and Tires. Check Tire pressure, wear and damage. Fittings and Fasteners. Check all fi ttings and fasteners. Drive Chains. Check chains for tension and lubrication. Adjust tension for 1/2″ – 3/4″ defl ection at mid point. Engine Manual. Read your engine manual completely and follow all instructions

Incoming search terms: