2006 KTM 250 SX-F 250 EXC RACING 400 EXC RACING 450 SX, XC, EXC RACING 525 SX, XC, EXC RACING, REPAIR MANUAL

0

Filed Under (KTM) by admin on 05-05-2012

download
Hot start lever (250 SX-F) If you pull the red hot start lever [1] during the starting procedure backward, a bore in the carburetor will be opened through which the engine may take in additional air. The result is a „lean” fuel-air mixture of the type needed for hot starts.
ENGLISH 7 OPERATION INSTRUMENTS » Headlamp switch (EXCUSA) In this model the headlamp is switched on with the pull switch [1] . Flasher switch The flasher switch is a separate unit and is mounted on the left portion of the handlebar. The wire harness is designed in a way that whenever you want to use your bike off-road, you can dismount the entire turn indicator system without affecting the function of the remaining electrical system. Flasher left Flasher right Starter button (EXC) Pushing the black starter button [2] will actuate the E-starter. Emergency OFF switch (EXC Australia) The red emergency-OFF switch [3] is arranged adjacent to the throttle grip. In this position, the E-starter is operational and the engine can be started. In this position, the E-starter and ignition circuits are interrupted.The E-starter cannot be actuated, and the engine will not start, not even if you attempt to start it with the kickstarter. Pushing the black starter button [4] will actuate the E-starter. 2 3 4 5 6 Indicator lamps The green control lamp [5] flashes in the same rhythm as the flashing indicator when the indicator is working. The blue control lamp [6] lights up when the high beam is on

Incoming search terms:

2007 KTM 250 XC-F, XCF-W, EXC-F 400 XC-W, EXC RACING 450 XC, XC-W, EXC RACING 525 XC, XC-W, EXC RACING 525 XC DESERT RACING INSTALLATION MANUAL

0

Filed Under (KTM) by admin on 05-02-2012

download
Headlamp switch (XC-W) In this model the headlamp is switched on with the pull switch [1] . Flasher switch The flasher switch is a separate unit and is mounted on the left portion of the handlebar. The wire harness is designed in a way that whenever you want to use your bike off-road, you can dismount the entire turn indicator system without affecting the function of the remaining electrical system. Flasher left Flasher right Starter button Pushing the black starter button [2] will actuate the E-starter. Indicator lamps The green control lamp [5] flashes in the same rhythm as the flashing indicator when the indicator is working. The blue control lamp [6] lights up when the high beam is on. ENGLISH 7 2 Emergency OFF switch (EXC Australia) The red emergency-OFF switch [3] is arranged adjacent to the throttle grip. In this position, the E-starter is operational and the engine can be started. In this position, the E-starter and ignition circuits are interrupted.The E-starter cannot be actuated, and the engine will not start, not even if you attempt to start it with the kickstarter. Pushing the black starter button [4] will actuate the E-starter. 3 4 5 6 1 OPERATION INSTRUMENTS » ENGLISH 8 TEST All of the display segments briefly light up for the display function test. WS (wheel size) The display changes and the circumference of the front wheel is briefly displayed in millimeters (2205 mm corresponds to a front wheel circumference of 21″ with production tires). Afterwards the display will return to the previous display mode

Incoming search terms:

HARLEY DAVIDSON MULTI-FIT BRAIDED THROTTLE/ IDLE CABLE KITS REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 01-02-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Disconnect battery cables, negative (-) cable first or remove the main fuse following the instructions in the service manual. NOTE When performing cable disassembly procedures, make careful notes as to the existing cable routing. Pay special attention to existing cable strap locations before removing so new straps can be placed into the same locations. Do not remove or install the master cylinder assembly without first positioning a 5/32-inch (4 mm) thick insert between the brake lever and lever bracket. Removing or installing the master cylinder assembly without the insert in place may result in damage to the rubber boot and plunger on the front stoplight switch. (00324a) 2. See Figure 1. Place the cardboard insert between the brake lever and lever bracket. 3. See Figure 2. Loosen cable adjuster jam nuts. Turn cable adjusters in until they are as short as possible. This will provide enough slack for easy removal. 4. Remove the right upper and lower switch housing screws INSTALLATION Throttle and Idle Cable Installation 1. See Figure 3. Apply graphite lightly to the throttle grip inside the switch housing and on the throttle end of the handlebar. NOTE The throttle control cable has a larger diameter retaining ring crimped to the cable end than does the idle control cable. For assembly, apply a drop of light oil on the retaining rings of the crimped inserts. 2. See Figure 7. Push the throttle cable housing and retaining ring into the larger hole of the switch housing, located in front of the tension adjuster screw. 3. Push the idle cable housing and retaining ring into the smaller hole of the switch housing, located behind the tension adjuster screw. 4. Push the throttle and idle control cable housings into the lower switch housing until each snaps into place. NOTE For models not equipped with factory-installed cruise control, if the friction shoe has fallen out or become dislodged, install the shoe with the concave side facing up and position it so the pin hole is over the point of the adjuster screw. 5. Push the throttle control grip over the end of the right handlebar until it bottoms against the closed end. Rotate the grip until the ferrule notches are at the top. To prevent binding, pull the grip back about 0.12 inch (3.2 mm). 6. See Figure 3. Position the lower switch housing beneath the throttle control grip. Install two brass ferrules (Item 3, Figure 11) from this kit onto cables, seating the ferrules in their respective notches on the throttle control grip. The cables must be captured in the grooves molded into the grip. 7. Position the upper switch housing over the handlebar and lower switch housing. Route the wire harness conduit through the depression at the bottom of the handlebar. 8. Tighten the upper and lower switch housing screws finger- tight. 9. Position the brake lever/master cylinder assembly inboard of the switch housing assembly, engaging the tab on the lower switch housing in the groove at the top of the brake lever bracket. 10. Align the holes in the handlebar clamp with those in the master cylinder housing and tighten the lower screw and flat washer finger-tight. Position for rider comfort. Beginning with the top screw, tighten the screws to 60-80 in-lbs (6.8-9.0 Nm)

Incoming search terms:

Yamaha XV 1300 V star XVS13AW OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 04-12-2010

download
1. Front turn signal/position lights (page 6-34) 2. Headlight (page 6-32) 3. Seat lock (page 3-11) 4. Fuel injection system fuse (page 6-30) 5. Fuse box (page 6-30) 6. Main fuse (page 6-30) 7. Helmet holder (page 3-12) 8. License plate light (page 6-35) 9. Rear turn signal light (page 6-34) 10.Engine oil level check window (page 6-11) 11.Shift pedal (page 3-8) 12.Engine oil filler cap (page 6-11) DESCRIPTION 2-2 2 EAU10420 Right view 1. Tail/brake light (page 6-33) 2. Rear brake fluid reservoir (page 6-22) 3. Owner’s tool kit (page 6-1) 4. Battery (page 6-29) 5. Air filter element (page 6-15) 6. Fuel tank cap (page 3-9) 7. Front brake fluid reservoir (page 6-22) 8. Brake pedal (page 3-9) 9. Engine oil filter cartridge (page 6-11) 10.Engine oil drain bolt (page 6-11) 11.Coolant reservoir (page 6-14) 12.Shock absorber assembly spring preload adjusting ring (page 3-12) DESCRIPTION 2-3 2 EAU10430 Controls and instruments 1. Clutch lever (page 3-8) 2. Left handlebar switches (page 3-6) 3. Multi-function meter unit (page 3-3) 4. Main switch/steering lock (page 3-1) 5. Right handlebar switches (page 3-6) 6. Throttle grip (page 6-16) 7. Brake lever (page 3-8) INSTRUMENT AND CONTROL FUNCTIONS 3-1 3 EAU10460 Main switch/steering lock The main switch/steering lock controls the ignition and lighting systems, and is used to lock the steering. The various positions are described below. EAU10540 ON All electrical circuits are supplied with power, and the meter lighting, taillight, license plate light and position lights come on, and the engine can be started. The key cannot be removed. NOTE: The headlight comes on automatically when the engine is started and stays on until the key is turned to “OFF”, even if the engine stalls. EAU10660 OFF All electrical systems are off. The key can be removed. EAU10680 LOCK The steering is locked, and all electrical systems are off. The key can be re- moved. To lock the steering 1. Turn the handlebars all the way to the left. 2. Push the key in from the “OFF” position, and then turn it to “LOCK” while still pushing it. 3. Remove the key.

Incoming search terms:

Audiovox CCS-100 Cruise Control Installation Manual

0

Filed Under (Tips and Review) by admin on 10-11-2010

download
You can see where I drilled the holes to mount the bracket. (2566, 2567) You’ll have to bend the bracket to fit and reposition it on the servo (the extra holes are already there on the servo to move the bracket). Just bend it until it lays flat on the back of the plastic box. You’ll have to unbolt the two bolts that hold the plastic box in place to work on it. I made the hole in the front of the box (where the servo cable goes through) way too large, but I wasn’t sure what angle it would be at when I installed it, so I kept cutting it bigger so the cable wouldn’t be bent too sharp. (2565) I ran the servo cable along the top frame under the tank, around the front cylinder and into a bracket (that came with the unit) that I cut off to fit. I attached the bracket to the screw on the air cleaner, but you really have to do a lot of grinding on the bracket to get it to fit the area so that it will lay flat and tighten up with the screw. You’ll see what I mean when you put a piece of metal or bracket up to that hole. It’s not flat, so I used a moto-tool to cut slots in the bracket and a grinder to grind it down smaller so that it would fit in that area. I used the long “cable” and no bead chain to connect to the throttle. (2560) First take off your throttle grip and release the “pull” cable (the front one) so you can remove it from the carb lever. Then put the cable end over the throttle cable end and re-insert it, then re-assemble your throttle. Hook the ball on the end of the long cable (there are two or three cables in the kit, use the long one) to one of the bead chain connectors (you have to spread it first) and then close it back up. (2563) Spread the other end and hook it to the servo cable and then using your pliers, close it again. Ok, now you have the servo all hooked up. You’ll need a vacuum canister, which you can buy at JC Whitney, or make one from PCV pipe (2″) with caps. (2554, 2555) Drill two 5/16″ holes in the pipe, tap(1/8″) them and insert brass 3/16″ nipples for your vacuum hose. (2568) Hook the black of the Napa one-way vacuum check valve end up to your engine vacuum and the blue end to your canister. I disconnected the emissions canister from the cylinder number one intake. I then uncapped the vacuum tap on the number two cylinder intake and connected the two together with a “T” (from the kit) and the connected the remaining end of the “T” to the black end of the check valve. (2556) The other nipple on your canister gets connected to the servo (drill a whole in the bottom of the black box to run it in). Wiring: Drill a hole in the top of the black box to run the wiring harness out. I’d suggest you take a roll of electrical tape and tape it up first. Leave the black ground wire out of the tape and also leave the purple and red wires out of the taped area about 8″ or 10″ up from the servo. You’ll want them near the servo so you can cross them over the bike to the right side and hook the black wire directly to the negative side of the battery. The purple wire connects to the yellow brake light wire and the red wire connects to the blue wire, which is hot when the key is on. The rest of the harness you can run along the left side of the frame, using wire tires to tie it off. Leave the blue wire out of the harness as you get to the front cylinder (so you can hook it to the front coil), or you could use the back cylinder coil. You can make a little “Y” harness out of spade connectors (female on one end, and male on the other two ends) to join the blue wire to the coil. Use the gray wire on the front coil or the orange wire on the rear coil

Incoming search terms:

KAWASAKI Z1000 GTR Electronic Cruise Control Installation Manual

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
The actuator spool is installed in the CIU housing with the actuator cable. The actuator spool is rotated to fully extend the cable. 2nd step. The dual spool and carburettor cable are installed. The carburettor cable is attached to the lower groove in the dual spool. The other end of the carburettor cable is attached to the carburettors. Note the position of the roll pin. It is nearly contacting the end of the groove in the actuator spool. The free play in the carburettor cable must be adjusted so that the cable outer can be pulled out 2 ~ 3mm before the carburettors start to open. This ensures that the cruise control cannot prevent the carburettors returning to idle. If more free play is allowed the response of the cruise control is compromised. This adjustment of free play is usually performed after final assembly of the CIU is completed and the CIU is in its final location. This is because flexing the cable affects the free play. It is shown at this stage in these diagrams to improve clarity. After this adjustment is performed, the carburettor cable adjustment MUST NOT BE MOVED. All future adjustments of free play in the throttle must be performed on the throttle cable from the throttle grip. If incorrect free play in the carburettor cable is suspected due to inconsistent cruise operation or because of inconsistent idle speed, the adjusters on the throttle cable from the hand grip must be backed all the way off to give as much free play as possible. If this does not result in AT LEAST 5mm of free play in the throttle cable, the throttle cable must be removed from the hand grip or CIU before adjustment of the carburettor cable is attempted. This is crucial because the amount of free play in the throttle cable also affects the apparent free play in the carburettor cable

Incoming search terms:

2008 KTM 250 SX-F 250 XC-F, XCF-W 250 EXC-F, EXC-F SIX DAYS INSTALLATION MANUAL

0

Filed Under (KTM) by admin on 22-10-2010

download
Hand brake lever The hand brake lever [1] is mounted on the handlebars on the right and actuates the front wheel brake. The adjusting screw [A] can be used to change the basic position of the hand brake lever (see “Maintenance”). 1 A Short circuit button The short circuit button [2] turns off the engine. When pressing this button, the ignition circuit is short-circuited. 2 Headlamp switch (XCF-W) In this model the headlamp is switched on with the pull switch [5] . 5 Flasher switch The flasher switch is a separate unit and is mounted on the left portion of the handlebar. The wire harness is designed in a way that whenever you want to use your bike off-road, you can dismount the entire turn indicator system without affecting the function of the remaining electrical system. Flasher left Flasher right
OPERATION INSTRUMENTS » ENGLISH 7 1 2 3 4 5 Starter button Pushing the red starter button [1] will actuate the E-starter. Emergency OFF switch (EXC-F Australia) The red emergency-OFF switch [2] is arranged adjacent to the throttle grip. In this position, the E-starter is operational and the engine can be started. In this position, the E-starter and ignition circuits are interrupted.The E-starter cannot be actuated, and the engine will not start, not even if you attempt to start it with the kickstarter. Pushing the black starter button [3] will actuate the E-starter. Indicator lamps The green control lamp [4] flashes in the same rhythm as the flashing indicator when the indicator is working. The blue control lamp [5] lights up when the high beam is on. TEST All of the display segments briefly light up for the display function test. Electronic speedometer The display in the electronic speedometer is activated as soon as you press a button on the speedometer or an impulse is received from the wheel sensor. The display lights up when the engine is running. The display is cleared if no button is pressed for 1 minute or no impulse is received from the wheel sensor. The button is used to change between display modes. The + and – buttons are used to control various functions

Incoming search terms:

Incoming search terms: