2008 Harley Davidson Touring models with an electronic throttle Grips Installation manual

0

Filed Under (Harley Davidson) by admin on 08-03-2012

download
1. Using a sharp knife, remove the rubber from your current grip by carefully cutting it away from the existing plastic throttle sleeve. The rubber that is adhered to the plastic sleeve must be ” shaved” resulting in a smooth plastic sleeve with no rubber. 2. Apply glue to the throttle sleeve. Use about 1/4 of the tube of glue on each side. Most of the glue should be applied to the end of the sleeve away form the throttle housing. 3. Slide the grip on to the throttle sleeve with one strong push. Use a rubber mallet if needed. Be sure not to get any of the glue into the space between the throttle sleeve and the throttle housing as well as the space between the throttle sleeve and the handlebar. *Wipe up any excess glue immediately

Harley Davidson Motorcycles Hot Grips Installation Manuals

0

Filed Under (Harley Davidson) by admin on 23-02-2012

download
End weights or other need to open the ends: You may drill out the outboard ends of the grips for installation of end weights or other purpose, if you use a fine tooth hole saw and do not go larger than the handlebar’s inside diameter. We have molded in a visual guide on the grip’s ends, and we recommend 7/8″ or at most 1″ diameter and be sure to center drill carefully. DO NOT use a hacksaw or you will destroy the grip, because there are resistance wires molded into the grip outboard of the handlebar diameter. Some Harley throttle sleeves are molded with raised plastic ribs or ridges to help hold the original Harley grip in place, and these will mate up with four (4) of our internal ribs by sliding our heated handgrip over the sleeve. HOWEVER, there are two axial ribs, which go circumferentially around the throttle sleeve as illustrated below, and they may have to be carefully removed with a knife of razor blade. They must be trimmed off with a file or razor knife until the Hot Grips slides over them. Do not force the Hot Grips over the ridges as the grip cannot stretch and will be damaged if forced on. These Hot Grips® have a heat output of 8 watts on “low” and 15 watts on “high” per grip. As a pair they will consume 20 watts of electrical power on “low” and 30 watts on “high”. They consume more than 8 x 2 on “low” because the resistor consumes a little

HARLEY DAVIDSON "LIVE TO RIDE" HANDLEBAR GRIPS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 02-03-2011

download
installation Do not lubricate the left grip of handlebar in any way before installation. This could allow grip to come off while riding which could result in loss of control of vehicle and death or serious injury. 1. Remove existing left handlebar grip by carefully cutting it away from the handlebar using a sharp blade or knife. Remove right grip/throttle sleeve assembly following instructions in appropriate Service Manual. After removal, make sure that left and right handlebar ends are clean and smooth. 2. Check that end caps are securely fastened to grips. Tighten screw inside grip to secure end caps. 3. Assemble new throttle sleeve to handlebar. Refer to appropriate Service Manual for detailed procedure. NOTE Surfaces to be glued must be clean, dry, and free from oil. If surfaces are not clean, dry, and free from oil, then the new application may not adhere as desired. Please observe the following WARNINGS when using the adhesive contained in this kit. FLAMMABLE, INJURIOUS TO EYES, HARMFUL IF SWALLOWED, VAPOR HARMFUL. FLAMMABLE: CONTAINS METHYL ETHYL KETONE. Use only in well ventilated areas. Avoid contact with eyes, mucous membranes, and prolonged skin contact. KEEP OUT OF REACH OF CHILDREN. If swallowed, do not induce vomiting. Call a physician immediately. This product contains a chemical(s) known to the State of California to cause cancer, birth defects or other reproductive harm. 4. Liberally apply a coating of Harley-Davidson Adhesive (Part No. 99839-95) to the inside of left handlebar grip using the cotton swab. Make sure adhesive fully covers all inside surface area of the grip. Also, apply a coat of adhesive to the handlebar end. 5. Check how the rectangular pattern is oriented on the throttle (right) grip. Align pattern on left grip to match right grip and immediately push the new grip completely onto handlebar end. 6. Rotate the end caps so the “Live to Ride”text is positioned at the top of both grips. NOTE Do not hesitate when installing left grip or adhesive will dry before installation is complete. Allow 6-8 hours at 70°F to achieve full cure of the adhesive. Prior to starting engine, verify that the throttle control will snap back to the idle position when released. A throttle control that prevents the engine from automatically returning to idle can lead to a loss of control of vehicle which could result in death or serious injury. Cleaning

Motorcycle Hand Warmer Installation Instructions

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
1. Disconnect the Positive (+) terminal from the battery. 2. Remove the existing grip from the Clutch side. Removing the grip may require blowing compressed air in the end between the grip and the bar, injecting brake cleaner fluid, or cutting it off. 3. Clean the handlebar where the grip was removed with alcohol or a solvent to remove all residue and dry with a clean cloth. 4. Determine where the Clutch side heater will be mounted. Take the heater marked “Clutch” and place it on the handlebar approximately ½” from the end and decide the position of the wires. It is recommended to mount the heater so the wires are at 9:00 o’clock or they can be positioned on the bottom for appearance. Peel off the release paper and adhere the heater to the handlebar with the wires toward the headlight. 5. Apply a high temperature adhesive (such as JB Weld) to the inside of the Clutch side grip. Install the grips over the heaters and let the adhesive cure as instructed by the adhesive manufacturer. 6. The Throttle side heater is installed on the throttle sleeve under the rubber cover. Remove the rubber cover that is installed over the throttle sleeve so the Throttle side heater can be applied. Some of the throttle sleeves have ribs which need to be cut or ground off so the heater can make full contact with the sleeve surface or it will over heat in the void areas. 7. Determine where the throttle side heater will be mounted. Take the heater marked “Throttle” and place it on the throttle sleeve approximately ½” from the end and decide the position of the wires. It is recommended to mount the heater so the wires are at 3:00 o’clock with a loop to allow for the twisting motion of the throttle. Peel off the release paper and adhere the heater to the throttle sleeve with the wires toward the headlight. 8. Apply a thin coat of adhesive (such as J.B. Weld) to the surface of heater only and reroll the rubber hand grip over the entire throttle sleeve. Wipe off any excessive adhesive that may have rolled out

Honda Shadow Aero 750 Kuryakyn Grips Installation Manual

0

Filed Under (Honda) by admin on 26-10-2010

download
Pull grip and chrome grommet off of throttle sleeve. (Here is the pic of doing the same thing on the clutch side.) Here is what you will be left with (I temporarily glued the threaded nipple back on the throttle sleeve for illustration…again, it will NOT be needed.)
Step 4: Clean off old glue with denatured alcohol. Note that an old pair of under shorts serves as an EGGSELENT rag for this use! Step 5: Remove grip from clutch side. End cap simply pulls straight off, split rubber OEM grip and pull it off, taking the chrome grommet on the end with it. With enough brute force, you can simply pull the end cap off and FORCE the grip off, but it is MUCH easier if you split it.

Incoming search terms:

Kawasaki, Suzuki and Yamaha GRIPS INSTALLATION

0

Filed Under (Tips and Review) by admin on 25-10-2010

download
1 (Fig. 1) 3 Apply glue to the throttle sleeve. Most of the glue should be applied to the end of the sleeve away from the throttle housing. 4 Slide the grip onto throttle sleeve with one strong push (Fig. 2). NOTE: Be sure not to get any glue into the space between the throttle sleeve and the throttle sleeve housing, as well as the space between the throttle sleeve and the handle bar. Wipe up any excess glue immediately. Allow 6 hours for glue to set before using . GRIPS Remove clutch side grip by carefully cutting it away from the handlebar with a sharp knife. 1 Apply glue to the bar. Most of the glue should be applied to the end of the bar away from the switch housing. 2 Slide the grip onto the bar with one strong push. Wipe away any excess glue immediately. Allow 6 hours for glue to set before using. (Fig. 3)