Harley Davidson Big Twin EVO Engines Edelbrock Performer-Plus Camshaft , Performer RPM Camshaft , & Performer RPM Camshaft INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 03-03-2012

download
Disconnect the battery. Secure the motorcycle on a suitable stand with the rear wheel off the ground. Remove components necessary for easy access to rocker covers, pushrod covers, and gear case cover, i.e., exhaust system, gas tank, air cleaner, foot rest, etc. Remove spark plugs. 2. Remove top and middle sections of rocker boxes, then rotate engine so both valves are closed on the cylinder head being worked on (put transmission in high gear and move rear wheel to slowly rotate engine). Remove the two 5/16″ bolts nearest the rocker arm shafts (keep all shafts, rocker arms, and pushrods in order so they can be installed in their original position). Remove the pushrod covers and pushrods. NOTE: The use of adjustable time-saver pushrods will simplify installation. Follow the manufacturer’s recommendations for installation of those parts. 3. It is not necessary to remove the tappet guides if you use a cam installation tool such as Crane #9-0020 to hold the tappets in place during cam installation. If you remove the tappet guides, you must use a tappet block alignment tool such as Crane #9- 0021 to re-install the tappet guides. Tappets can be held up in place during removal of guides by using U-shaped piece of safety wire or paper clip hooked to the tappets. 4. Remove ignition covers on gearcase cover by drilling out rivets to gain access to sensor plate. Remove the inner cover, sensor plate and rotor. NOTE: For re-installation, use new rivets H-D #8699 or drill and tap for 10-32 screws. 5. Remove the gearcase cover screws and remove cover while holding end of cam inward. Now remove the camshaft, spacing washer and thrust plate

Incoming search terms:

BMW K1100LT/ RS Repair Manual

0

Filed Under (BMW) by admin on 03-12-2010

download
00.3 00 Tightening torque Model K 1100 LT K 1100 RS Connection Nm 11 Engine Freewheel Cover plate/freewheel cage at countershaft gear 10 Oil – water pump Oil pressure switch 40 Temperature sensor/screw plug 9 Pressure relief valve 40 Impeller 33 Pump housing to crankcase 10 Cover to pump housing 10 (3-Bond 1209) Intermediate flange Thrust plate at intermediate flange 9 (Loctite 243) Intermediate flange at crankcase 9 Crankshaft Pinion/rotor flange at crankshaft 50 Main bearing cap to crankcase 50 Connecting rod Big end cap Wrench angle 80 ° 30 Input shaft Front bearing 18 Rear bearing 40 Engine block Crankshaft cover 9 Lower part, outer 10 Oil sump 10 Oil filter cover 10 Oil drain plug 30 Cylinder head Cylinder head bolts (SI 11 062 95 (697) Short thread (from 6/93 to 11/94): Wrench angle, 1st stage Wrench angle, 2nd stage Long thread (since 12/94): Wrench angle, 1st stage Wrench angle, 2nd stage 64° 42° 75° 75° 22 20 Cylinder head cover 9 Camshaft Bearing cap 9 (Apply a thin coat of 3-Bond 1209 only at corners and butt edges) Chain sprockets 54 00.4 Timing chain Chain tensioner 9 Slide rail at camshaft bearing cap 9 Timing case cover Timing case cover 10 (3-Bond 1209) Cover for Hall-effect signal transmitter 9 Screw plug 40 Clutch Clutch housing to output shaft Tighten to Release and re-tighten to Wrench angle 50° 140 50 Housing cover 19 Alternator Alternator to intermediate flange 22 Driver 33 Starter motor Starter motor to gearbox 9 Mixture preparation Intake stub pipe 9 Fuel injection rail 9 Cooling system Coolant stub pipe at cylinder head 9 Temperature sensor at coolant stub pipe 30 Air cleaner Lower part of air cleaner housing 21 12 Engine electrical system Starter to transmission 9 Positive lead to starter 5 Alternator to intermediate flange 22 Clutch housing 50 Base plate 3,5 Setting ring 2,5 Hall generator cover 9 Ignition coils to intermediate flange 5 Spark plug 20 Model K 1100 LT K 1100 RS Connection Nm 00.5 13 Fuel preparation and control Injection rail 9 Intake stub pipe 9 Lower section of air cleaner housing 21 Intake air line 9 Motronic control unit 5 17 Radiator Connecting screw, temperature sensor 9 Fastening, thermostat cover 3 Radiator to frame 9 Coolant stub pipe to cylinder head 9 (with Loctite 243) Temperature sensor to coolant stub pipe 30 18 Exhaust System Exhaust system to cylinder head 21 Front silencer (muffler) 12 Exhaust system holder to footrest plate 33 Exhaust system to holder/footrest plate 9 Retaining bracket to gearbox 41 Oxygen sensor Hand-tight 21 Clutch Clutch housing to output shaft tighten to loosen and retighten to tightening angle 50° 140 50 Housing cover

Incoming search terms: