Honda 400EX Hub installation instructions

0

Filed Under (Honda) by admin on 20-12-2011

download
Remove all contents from its packaging and verify that all parts are present and free from damage. You should have the following items: (2) wheel hubs (2) smaller tapered bearings (2) large tapered bearings (2) wheel bearing nuts (2) dust caps (2) inner bearing seals (6) M3 x .5 screws (2) cotter pins (2) inner bearing spacers 2. Completely remove the old hubs from your quad and clean the spindle and the surrounding areas. It is very important to keep the new bearings and seals clean during installation for long life. Be sure to remove the factory inner bearing spacers from the spindle and discard. They will not be used in re-assembly. 3. Pack your new Timken tapered wheel bearings with a liberal amount of high quality wheel bearing grease. A wheel bearing packer works best, however you can accomplish the task by placing the grease in the palm of your hand and manually working it in between the bearing rollers. We also recommend that you pack the area between the bearing races in the hub with grease for additional lubrication and protection against moisture. 4. Place the large wheel bearing (inner) into the hub and install the inner seal. The seal should bottom out against the step in the bore and the face should be flush with the hub. 5. Remove the brake rotors from your old hubs. Re-install the rotors on your new hubs and be sure to use medium strength Loctite on the threads. 6. Apply a light film of grease or oil to the large diameter of the spindle stud. Install the new o-ringed bearing spacer onto the spindle. 7. Apply a thin film of grease to the seal surface on the bearing spacer and the inside diameter of the seal to prevent the seal from running dry. Install the hub onto the spindle and slide the outer bearing over the spindle and install the new bearing nut furnished with your hubs. Do not use the factory nut or washer. 8. SETTING THE BEARING PRELOAD: It is first necessary to seat the bearing before setting the preload. This aligns the rollers and prevents the bearings from loosening after a short period of use. To seat the bearing, tighten the spindle nut while you rotate the hub until the hub becomes difficult to spin. With the bearing now seated, you must set the bearing preload. Preload means placing a small amount of force against the bearings to remove any clearance between the bearing race and the rollers. This is done by backing the nut off completely and re-tightening it with your fingers. Do not rotate the hub while setting the preload . If a hole in the spindle is not accessible for installation of the cotter pin, adjust the nut tighter to bring a hole into alignment. Install the cotter pin and bend the pin around the outside of the nut. Do not attempt to bend the pin toward you (over the end of the spindle) or it may rub on the inside of the dust cap.

Incoming search terms:

HARLEY DAVIDSON TIMKEN BEARING CONVERSION TOOL INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-03-2011

download
2-ton press (must be square to within .010″, ram to table) Inch-lb torque wrench Foot-lb torque wrench T15 TORX® drive socket (for inch-lb torque wrench) 5/32 inch hex drive socket (for inch-lb torque wrench) 5/16 inch hex drive socket (for foot-lb torque wrench) 5/64 inch hex key wrench 1/16 inch hex key wrench 3/8 inch drive hand drill small tap handle (suitable for #8-32 tap) Tapping Fluid Press Fit Lube (non-drip) Loctite® 620 threadlocker and sealant The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references service manual information. A service manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Kit Contents See Figure 21 and Table 3. If replacement parts are needed contact JIMS® at 805-482- 6913 or INSTALLATION 1. Remove and disassemble the engine as necessary to remove the left side engine case. Bearings and seals must be removed from the left case. Refer to the service manual for the disassembly procedures. 2. Use an appropriate solvent to clean the left engine case. Also clean the bearing sleeve (1) supplied in the kit. 3. Apply Loctite 620 to the smaller inside diameter portion of the left case bearing bore. 4. See Figure 1. Apply Loctite 620 using a cotton swab to the smaller portion of the outside diameter (2) surface of the bearing sleeve (1). 5. Apply a spare amount of non-drip press fit lube (3) to the larger outside diameter of the bearing sleeve. 6. See Figure 2. Fit the bottom locater plate (1) to the to the outside of the case over the bearing bore. The word “BOTTOM” will be at the bottom of the case when installed at the 6 o’clock position

Incoming search terms:

Incoming search terms: