HARLEY DAVIDSON VRSCD SADDLEBAG MOUNTING KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 14-04-2011

download
INSTALLATION Prepare Bike for Hardware Installation 1. Use a suitable lift to support the motorcycle under the frame until the rear suspension is fully extended. NOTE To remove the tether from the hole in the frame, reach under the frame tube to align the metal tee (located on the end of the seat tether) with the tether cable. 2. See Figure 1. Unlatch and open seat. Remove tether (4) by sliding small clip (3) sideways through hole in frame. NOTE To remove the tubular plastic seat-hinge sleeve from the hinge, turn the sleeve to reveal the slotted length. Push on the slot with your finger to pop the sleeve off the hinge pins. Closing the seat slightly allows the sleeve to fall from the hinge-side of the seat, so be prepared to catch the sleeve. 3. Remove plastic sleeve (2) from hinge pins (1) and slide pins toward rear of bike. Remove seat. 2 1 4 3 is 00449 1. Hinge 2. Sleeve 3. Clip 4. Remove tether from frame Figure 1. Remove Seat 3 1 2 is 00450 1. Grabstrap 2. Passenger Pillion 3. Screw and Washer Figure 2. Remove Passenger Pillion 4. See Figure 2. Remove screw and washer (3) securing passenger pillion to frame. Slide pillion under grabstrap (1) and forward to disengage from tongue to remove. Save pillion mounting screw and washer for later use

HARLEY DAVIDSON TOURING SEATS REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 09-02-2011

download
REMOVAL NOTE Cover painted surfaces with protective material to prevent scratches or other damage. 1. Remove the left and right side saddlebags from the motorcycle per the instructions in the owner’s manual. Save all hardware for installation. 1 3 2 4 5 is05863 1. Stock screw 2. Stock washer 3. Stock grab strap 4. Saddlebag mounting bracket 5. Grab strap (kit 53051-09) Figure 1. Remove Grab Strap and Install Kit 53051-09 NOTE Before removing the saddlebag mounting bracket attaching bolts, note the mounting orientation of the saddlebag mounting brackets. 2. See Figure 1. Remove the left side screw (1) and washer (2) to remove the bracket (4) and the passenger grab strap (3). Repeat for the right side saddlebag mounting bracket. 3. See Figure 4. Remove the screw with lockwasher (A) from the rear of the currently installed seat. Pull the seat rearward to remove the seat from the motorcycle. Save the screw. 4. For All Kits Except 53051-09: Remove the two flanged nuts (B) from the studs (C) near the front of the rear fender. INSTALLATION For All Kits Except 53051-09: 1. Install the grab strap (2) onto the studs as shown in Figure 2. Secure the grab strap to the studs with the nuts, and tighten to 96-156 in-lbs (11-18 Nm) . 2. See Figure 3. Slide the rear of the seat (1) through the grab strap, from the front, until the slot (2) on the front underside of the seat is behind the seat mounting tongue (1) on the fuel tank rear bracket

HARLEY DAVIDSON XL SEAT KITS REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
1 2 is 00911 1. Tongue 2. Keyhole Figure 2. Underside of 2-up seat INSTALLATION NOTE If installing the seat with a sissybar/backrest pad present, remove the backrest pad prior to seat installation. This will prevent damage to the pad and/or seat. Reinstall backrest pad after the seat is installed. 1. Models equipped with solo seats: See Figure 1. a. Remove the plastic plug (1) from the rear hole location in the fender (2). Save the plastic plug for installation. b. Move the seat retention nut (4) and lockwasher (5) from the middle location to the rear location, where the plug was just removed. As shown in the inset, a cable strap (6) can be used as an installation aid. Place the retention nut (5) over the cable strap so that the wide end of the nut rests on the eye of the cable strap. Thread the cable strap up under the fender, and through the fender hole. Pull up on the cable strap to hold the nut snug against the underside of the fender. c. With the rib of the retention nut (4) seated into the notch in the fender hole, slide the retension washer (5) into place from the rear. This will lock the retention nut in place. d. Reinstall the plastic plug in the fender hole in the middle location. NOTE The foam cushioning of the seat needs to be compressed as the seat is slid forward to engage the post on the frame when the seat is dropped into place. When properly installed, the front tongue on the underside of the seat should fit snugly in the groove at the fuel tank rear mounting location and the keyhole on the underside of the seat will lock the seat to the post on the frame. 2. All models: See Figure 2. a. Angle the front of the new seat into place so the tongue (1) engages the slot at the rear fuel tank mounting location. b. Push the seat forward and rotate the rear of the seat downward until the seat contacts the frame. Flex the seat slightly in the middle and slide the seat towards the rear so that the keyhole slot (2) on the seat bottom engages with the center seat post on the frame. 3. See Figure 3. Pull up on the center of the seat to verify that it is locked into place. (There will be a small amount of play, but the seat should only come up about a half an inch and then will be held firmly in place by the post on the underside of the seat.) If the seat is not firmly in place, repeat Step 2 until the seat is firmly in place. Reference the Owners Manual for further instruction on seat placement if needed

Incoming search terms: