HARLEY DAVIDSON SOFTAIL LEFT SIDE LEATHER TOOL BOX KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 19-04-2011

download
Installation While handling and installing tool box, be careful not to scratch surface. 1. See Service Parts Illustration. Install tool box (1) to mounting bracket (6) using button head screws (2) and washers (5). Screws (2) should be inserted through mounting holes on inside of tool box (1) and then inserted through bracket (6) holes and threaded into weld nuts attached to bracket. 2. Remove and save the two screws that secure left rear fender support to motorcycle frame. 3. Remove two bolts, nuts, and washers that secure debris deflector to motorcycle frame. This will allow you to move debris deflector out of the way when installing new passenger footpeg support bolt. Save hardware for reinstallation. 4. For 1990 to 1999 Softails: If tool box is being installed with passenger footpeg, remove the hex head bolt and left passenger footpeg. Retain footpeg and lockwasher for reinstallation. Discard bolt . If tool box is being installed without passenger footpeg, remove hex head bolt and left passenger footpeg. Discard footpeg. Retain bolt and lockwasher. For 2000 and later Softails: See page 3 . Remove footrest from clevis. Remove clevis from frame by removing cap screw from center of clevis. If tool box is installed with footpegs, keep all hardware. If toolbox is to be installed with footboards, discard hardware. 5. Slide top of mounting bracket (6) between rear fender support and frame. Align top holes in bracket with fender support holes. Align lower bracket hole with footpeg mounting hole in frame. Install the two screws, removed in Step 2, in fender support. Do not tighten screws at this time. 6. For 1990 to 1999 Softails: Place lockwasher retained in step 4 on footpeg support hex head bolt (3) from kit. CAUTION 1 of 3 For 2000 and later Softails with footpegs: Install kit 49352-00 according to instructions included in this kit. Footpeg must fold up at a 45┬░angle (from vertical) toward rear of motorcycle. This angle allows footpeg to fold up if, by accident, it strikes the ground surface when making a sharp turn. Failure to set footpeg to the proper fold-up angle could result in death or serious injury. 7. For 1990 to 1999 Softails: Position footpeg so it folds up and back at a 45┬░angle. Install bolt (3) from kit through frame, tool box bracket (6), and spacer (4), into footpeg, as shown. NOTE If vehicle is equipped with saddlebag support bracket, Part No. 90346-90 or 90346-94, position saddlebag support bracket between tool box bracket and spacer.

Incoming search terms:

HARLEY DAVIDSON SOFTAIL PASSENGER FOOTBOARD SUPPORT KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-04-2011

download
INSTALLATION Remove Existing Equipment 1. Remove existing footpeg and attaching hardware. 2. Remove chrome swingarm pivot covers, if so equipped. 3. Do not remove tool box, if so equipped. Install Passenger Footboard Support Kit 1. See Figure 1. Install footboard mounts (1) and (2) as fol- lows: a. Position footboard mount and insert screw (3) through part and into footpeg mounting hole. b. Position semi-circular cutout in mount extending from side of mount around nut of swingarm pivot bolt. c. Tighten screw (3) to 45-50 ft-lbs (61-67.8 Nm). 2. Position footboard support (4) on mounting stud so that bolt hole aligns with machined groove in stud. 3. Insert screw (5) through left side in split hub of footboard support. Thread into tapped hole (right side) of split hub. 4. Tighten screw (5) to 10 ft-lbs (13.6 Nm). 5. Place spring (6) into retaining hole in footboard support. Rest ball (7) on top of spring. 6. Refer to appropriate I-Sheet for instructions to install the footrest (A) and pivot pins (8) for your motorcycle

HARLEY DAVIDSON LEFT SIDE TOOL BOX KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 06-03-2011

download
INSTALLATION NOTE While handling and installing tool box, be careful not to scratch surface. 1. See Figure 1. Attach the toolbox (4) to the toolbox mounting bracket (1) using the three pan head screws (2) and Nylock nuts (3) from the kit. 2. Remove the two button head screws (I) which secure left rear fender support (B) to motorcycle frame (C). Retain screws for reassembly. 3. On models with passenger footpegs: a. For FLSTN models: Remove button head screw (N) and left footrest bracket (O) with attached footrest support (F) and footrest (E). b. For all other models: Remove the locknut (G), hex head bolt (J), spring washer (H) and footpeg (E). Remove the socket head cap screw (K) that secures the footrest support (F) to the frame (C). c. Remove the two bolts, nuts and washers which secure the bottom of the splash guard to the swingarm. This will allow you to move splash guard when installing the new passenger footrest bolt. d. Retain all removed components. 4. On models with passenger footboards: a. Remove the screw securing the passenger footboard assembly to the frame. Remove the footboard assembly. b. Retain all removed components. 5. Slide the top of mounting bracket (1) between rear fender support (B) and frame (C). Align top holes in bracket with fender support holes. Align lower bracket hole with footrest mounting hole in frame. Install the two screws (I), removed in Step 2, in fender support. Do not tighten screws at this time. Footrests must fold up and toward rear of motorcycle if struck. Failure to set footrests to fold up and back could result in death or serious injury. (00366a) 6. On models with passenger footpegs: a. For FLSTN models: Install button head screw (N) and left footrest bracket (O) with attached footrest support (F) and footrest (E) on top of the toolbox bracket (1). Tighten screw to 35-45 ft-lbs (47.5-61.0 Nm). b. For all other models: Refer to instructions in footpeg extension kit, Part Number 49352-00 for installation, and install the extention kit, footrest support and footpeg on top of the toolbox bracket (1). c. Install the two bolts, nuts and washers and secure the bottom of the splash guard to the swingarm. 7. On models with passenger footboards: a. Position footboard assembly, in the same orientation as removed, on top of tool box bracket. b. Install screw removed in Step 4. Tighten to 35-45 ft- lbs (47.5-61.0 Nm)

Incoming search terms: