2006 RIDGELINE MOTORCYCLE WHEEL GUIDE INSTALLATION And REMOVAL

0

Filed Under (Honda) by admin on 17-11-2011

download
Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures
should not be attempted by “do-it-yourselfers.” NOTE: • Be careful not to damage the body finish. • Determine the location of the wheel guide. One or more wheel guides can be installed in three different locations. 1. Remove the left front upper tie-down hook (two torx bolts). Remove the right front upper tie-down hook (two torx bolts). While wearing eye protection, enlarge the eight holes to 9 mm from the outer surface side of the front bed panel. Remove all burrs from the edges of the holes with a file.

2009 Honda CRF450R Decompression Plunger PRODUCT UPDATE CAMPAIGN

0

Filed Under (Honda) by admin on 21-04-2011

download
JH2PE053*9K700001 thru JH2PE053*9K703372 (*) Denotes check digit UPDATE PROCEDURE DEALER VENTORY Any affected unit in your inventory must be updated with a new decompression plunger and weight before delivery to the customer. Refer tothe PARTS INFORMATION and the UPDATE PROCEDURE sections of thisb Service Bulletin. Refer to the 2009 CRF450R Service Manual for specific removal instructions. 1. Remove the seat (page 3-3). 2. Remove the shrouds (page 3-4). 3. Properly hang the fuel tank (page 4-6). 4. Remove the camshaft (page 9-10) CUSTOMER INFORMATION: The information in this bulletin is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely maintain your Honda. These procedures should not be attempted by “do-it-yourselfers,” and you should not assume this bulletin applies to your Honda, or that your Honda has the condition described. To determine whether this information applies, contact an authorized Honda dealer. 5. Replace the decompression weight and plunger with kit parts (page 9-14). 6. Reinstall all previously removed parts. IDENTIFICATION When you have completed the update, place a punch mark before the first digit of the V.I.N. located on the right side of the steering head. 0080 WARRANTY INFORMATION This Product Update Campaign ends on arch 7, 2012. Normal claim submission requirements apply. fter completing the UPDATE PROCEDURE,submit one warranty claim per unit with the following information: WARRANTY CLAIM TEMPLATE: Template: R02A* Flat Rate Time: 1.2 hours *Template reads “R-zero-2-A”.

Incoming search terms:

2001 – 2002 GL1800/ GL1800A Rear Tire Inspection

0

Filed Under (Honda) by admin on 27-11-2010

download
1. Inspect the motorcycle for a punch mark as described in Identification on page 2. If a punch mark is present no further action is necessary, return the unit to the customer. 2. Qualify the unit/customer as follows: •Is the tire on the motorcycle the original factory installed tire? •Is the air pressure loss more than three psi per month? Note: Refer to page 145 in the Owner’s Manual. “Even tires that are in good condition may lose one to two psi per month if not checked and adjusted regularly” . If the GL1800 meets the above qualifications, proceed with the repair procedure. 3. Place the motorcycle on a lift and secure it on the centerstand. 4. Remove the rear wheel as described on page 14-9 of the Service Manual. 5. Starting at the valve stem/balance mark area, carefully remove the rear tire from the wheel. Be sure to use plenty of commercially available tire lubricant on the inside and outside of both beads. 6. Carefully inspect the entire circumference of both tire beads. Inspect both the inside and outside of the bead for any distortion or injuries. See examples of injuries below. 2001 – 2002 GL1800/GL1800A Rear Tire Inspection GL1800 #6 OCTOBER 2001 MTB 9430 (0109) CUSTOMER INFORMATION: The information in this bulletin is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely maintain your Honda. These procedures should not be attempted by “do-ityourselfers,” and you should not assume this bulletin applies to your Honda, or that your Honda has the condition described. To determine whether this information applies, contact an authorized Honda dealer. Service Bulletin American Honda Motor Co., Inc. 2001-2002 GL1800/GL1800A Rear Tire Inspection 0110 GL1800 #6*GL1800 #6*0110*2001-2002 GL1800/GL1800A Rear Tire Inspection*GL1800/GL1800A, Rear Tire Inspection, Bead, Tread*Motorcycle*1800 2 of 4 ©2001 American Honda Motor Co., Inc. – All Rights Reserved GL1800 #6 OCTOBER 2001 Inside BeadInjury Outside BeadInjury Outside BeadInjury 7. Carefully inspect the entire circumference of both tire beads. Inspect both the inside and outside of the bead for any distortion or injuries. See examples of injuries below. 8. If there is no evidence of bead damage, re-install the tire on the rim. Be sure to use plenty of commercially available tire lubricant on the inside and outside of both beads. Be sure to align the balance dot with the valve stem. Inflate the tire to 41 psi. Install the wheel assembly on the motorcycle and proceed to the Identification and then to the Warranty section. 9. If any damage or injury is present replace the tire and valve stem. Be sure to use plenty of commercially available tire lubricant on the inside and outside of both beads. Balance the new tire as necessary

Incoming search terms: