Honda ST 1300 Series Single Shock Supplement

0

Filed Under (Honda) by admin on 13-02-2011

download
Check the orientation of the adjuster on the shock body – looking at the top of the shock, the hydraulic line port should be165 degrees (clockwise) from the nitrogen pressure valve (see figure 2) . If it is not properly oriented, you will need to reposition it. To do this, hold the upper shock eye securely in a vice and carefully rotate the Remote Adjustable Pre-Load adjuster the desired direction. This may be somewhat difficult due to spring tension, and may require slight loosening of the locking ring. Also, the spring, shaft, and lower mount may rotate while repositioning the adjuster. This is OK, just be sure to realign it with the upper mount (also be sure the rebound adjuster on the lower mount is properly oriented as noted below). Mount the shock as you would your stock shock per your authorized shop manual (with the rebound adjustment at the bottom) noting the following: n As you mount the shock, feed the Remote Adjustable Pre-Load adjuster through the same path as the stock line was routed to the same location. n Do not loosen or attempt to rotate the line between the shock and the adjuster. n Make sure the shock rebound adjustment is facing the right side of the motorcycle and the pressure valve is facing up and towards the rear (figure 3) . n Tighten shock bolts to the proper torque specifications (refer to your manual). n Mount the adjuster to the supplied mounting bracket adapter using the supplied M6-1.0X8mm SHCS fasteners and torque them to 80- 90 in/lbs (9-10 N-m). Then mount the bracket and adjuster to the bike in the same location as the stock preload adjuster using the supplied M6-1.0X20mm SHCS fasteners & nuts, and torque them to 80-90 in/lbs (9-10 N-m) (figure 4 & 5) . n Using the supplied zip-ties, secure the hydraulic line away from any moving parts or heat sources.

Kawasaki KLR-650 465 Series Single Shock Supplement

0

Filed Under (Kawasaki) by admin on 13-02-2011

download
Mount the shock as you would your stock shock per your authorized shop manual (with the rebound adjustment at the bottom) noting the following: n As you mount the shock, feed the Remote Adjustable Pre-Load adjuster through the opening between the main-frame and sub-frame on the left side of the bike. n Do not loosen or attempt to rotate the line between the shock and the adjuster. n Make sure the shock rebound adjustment is facing the right side of the motorcycle and the pressure valve is facing forward. n On 1987-2007 models ONLY , install the supplied 3.5mm thick spacers – one on each side of the shock clevis ( see figure 3 ). Do not install these spacers on 2008-2010 models. n Tighten shock bolts to the proper torque specifications (refer to your manual). n Mount the adjuster to the supplied mounting bracket using the supplied M6- 1.0X8mm SHCS fasteners and torque them to 80-90 in/lbs (9-10 N-m). Then mount the bracket to the bike using the two rear footrest mounting bolts – sandwiching the mounting bracket between the rear footrest mount and the frame tabs (as shown in figure 4) . Using the supplied zip-ties, secure the hydraulic line away from any moving parts or heat sources. n To adjust the ride height, simply turn the adjuster knob clockwise (looking at it from the back of the bike) to increase the height and counterclockwise to reduce it. See main instructions for procedure of achieving optimum ride heigh

HARLEY DAVIDSON SADDLEBAG RAIL BRACKET KIT INSTALLATION ISNTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
Installation 1. See Figure 1. Remove two stock screws and nuts from one side of the saddlebag rail assembly. 2. See the Service Parts illustration. Insert two screws (3) through the screw holes from the opposite direction as the stock screws removed from the rail bracket in Step 1. 3. Place a spacer (2) on the outboard screw. 4. Place a Saddlebag Rail Bracket over the rail assembly. Position the bracket with the square notch on the inboard side of the rail assembly. 5. Fasten the screws from step 2 into the Saddlebag Rail Bracket. Torque the fasteners to 10 ft-lbs (13.5 Nm). 6. Repeat steps 1 – 5 for the saddlebag rail assembly on the other side of the motorcycle

HARLEY DAVIDSON ROAD KING SOLO BUCKET AND PASSENGER PILLION INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 10-02-2011

download
Installation SOLO SADDLE ONLY 1. Remove stock seat and grabstrap according to applicable Service Manual instructions. 2. Road King standard models . Remove and save the stock screws and seat mount bracket at the back of the rider solo seat. 2000 and later models . Remove the retainer washer from the stud plate and replace with two black retainer washers (2). Be careful not to allow stud plate to fall through the fender. 3. Road King standard models . Install stock solo seat mount bracket using two stock screws saved in Step 2. Road King Classic Custom models . Install solo seat mount bracket onto back of solo seat using bracket and screws included in Mount Kit Number 52903-01. 4. Install seat by sliding front of seat into seat holder bracket. Pull up on the nose of the seat to verify that the seat is securely installed. After installing seat, pull upward on front of seat to be sure it is in locked position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070a) 5. 1999 and later models . Install 1/4 in. star washers (6), spacers (4) and acorn nuts (3) onto rear mount studs. Torque to 72 in-lbs (8.13 Nm). 1998 and earlier models . Install 5/16 in. star washers (5) and 5/16-18 x 3/4 in. buttonhead screws (1) into stock mount nuts. Torque to 17 ft-lbs (23 Nm). SOLOAND PILLION 1. Remove stock seat and grabstrap according to applicable Service Manual instructions. Retain all hardware for later use. 2. Road King standard models . Remove and save the stock screws and seat mount bracket at the back of the rider seat. 3. Road King standard models. Install stock seat mount bracket onto new solo seat using two screws saved in Step 2. Road King Classic Custom models. Install solo seat mount bracket onto back of solo seat using bracket and screws included in Mount Kit Number 52903-01. 4. 1999 and later Road King standard models . Secure the rear mount bracket with stock mushroom nuts (10) and two 1/4 in. star washers (6). Torque to 72 in-lbs (8.13 Nm). 1998 and earlier Road King standard models . Install solo seat by sliding front of seat into holder bracket on bike. Secure the rear mount bracket with the two mushroom screws (11) and two 5/16 in. star washers (5). Torque to 17 ft-lbs (23 Nm). Road King Classic Custom models . Mount Kit Number 52903-01 is required for installation. Install solo seat (7) by sliding front of seat into holder bracket on bike. • 1999 and later models . Using Mount Kit Number 52903-01, secure the rear mount bracket with the two mushroom nuts (10) and two 1/4 in. star washers (6). Torque to 72 in-lbs (8.13 Nm). • 1998 and earlier models . Using Mount Kit Number 52903-01, secure the rear mount bracket with the two mushroom screws (11) and two 5/16 in. star washers (5). Torque to 17 ft-lbs (23 Nm)

Incoming search terms:

HARLEY DAVIDSON SOFTAIL SADDLEBAG KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 10-02-2011

download
INSTALLATION Do not exceed saddlebag weight capacity. Put equal weight in each bag. Too much weight in saddlebags can cause loss of control, which could result in death or serious injury. (00383a) NOTES Maximum saddlebag weight capacity is 7 lbs (3.18 kg) for each bag. Proper installation of these kits requires that tasks be completed for one side of the motorcycle first before continuing to the opposite side. 2000-2002 Models with Wide Tire Kit 1. See Figure 1. Remove and discard stock screws (1) and washers (2) from fender support. Button head screws from wide tire kit must be installed with button heads on inside of fender. Fastener contact with tire can lead to premature tire failure, which could result in death or serious injury. (00417b) 2. See Table 3. Determine appropriate screw from wide tire kit. 3. See Figure 2. Install saddlebag using screw (from wide tire kit) (1), washer (2) and nut (3). The screws are installed from inside to outside of fender. NOTE If you do not have the appropriate screw from the wide tire kit, it can be purchased from a Harley-Davidson dealer. Table 3. Wide Tire Kit Screws (3/8-16) Wide Tire Kit 44490-00, Hardware Kit 43763-00 Wide Tire Kit 44490-00, Hardware Kit 43761-00 Part Number and Length X X 4030 – 2-1/2 inch X X 4225 – 3-1/2 inch X X 4224 – 1-1/2 inch X X 4044 – 1-1/4 inch X 4215 – 2 inch X 3912 – 2-3/4 inch X X 4228 – 2-1/4 inch X X 4229 – 3-1/4 inch Failure to tighten saddlebag mounting bolts to specified torque could result in damage to saddlebags. (00406c) 4. Tighten all saddlebag hardware to 22 ft-lbs (30 Nm). NOTE Check that front screws have at least one thread exposed beyond the nut after proper torque has been applied. 5. Install reflectors on saddlebag. Refer to Install Reflectors subtopic.

HARLEY DAVIDSON DYNA DOCKING HARDWARE KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 09-02-2011

download
INSTALLATION Installing the Front Docking Point To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Remove the seat and disconnect the negative (-) battery cable. NOTE To keep the fender aligned, complete ALL the following procedures on one side of the motorcycle before starting the other side. 2. See Figure 1. Remove the stock fender support bracket. Position new rear fender mounting bracket from kit (5) into position. 3. Apply Loctite 243 (Blue) to button head bolt (2) prior to installation. Place the tapered side of front docking point (1) against the strut cover. Insert button head bolt (2) through the docking point, fender support and fender. Tighten to 12-18 ft-lbs (16.3-24.4 Nm) . 4. If used without saddlebags, install rear docking point (3) and recess cover (4) according to instructions in Part Number 53968-06C, Directional Relocation Kit. If used with saddlebags, mount rear docking point according to instructions with saddlebag kit. MAINTENANCE NOTE In time, the docking points may wear causing the mating luggage rack or sideplates to become loose. The fit may be tightened using the following procedure. If any fasteners with Loctite are loosened, then the fasteners must be removed, cleaned of existing Loctite and re-installed with new Loctite. 1. Loosen the docking hardware. 2. Rotate the docking points clockwise approximately 45°. 3. Tighten the docking hardware to the appropriate torque values as indicated in the installation procedures. This procedure can be repeated up to 3 times before replacement of the docking points is recommended.

Incoming search terms:

HARLEY DAVIDSON GLOSS BLACK TRIPLE TREE COVER KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 07-02-2011

download
INSTALLATION 1. Refer to the service manual to remove the front panel, side panels and trim strips. Save all hardware to install the new panels from the kit and trim strips. 2. See Figure 1 and Table 1. Install new panels from the kit and trim strips (D). 3. Tighten screw (A), three places, to 20-30 in-lbs (2.26-3.39 Nm) Tighten screw (B), two places, to 12-17 ft-lbs (16.3-23.0 Nm) Tighten screw (C), four places, to 8-12 ft-lbs (10.8-16.3 Nm) . If installing on a motorcycle with a light bar or windshield, refer to the appropriate service manual or instruction sheet for torque values.

HARLEY DAVIDSON ENGINE GUARD KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 06-02-2011

download
This kit fits 1991 and later Dyna Glide models except Dyna models equipped with forward controls, 1993 and later FXDWG, 1994 and later FXDS Dyna Convertible models Installation The slider tubes on the front forks of some motorcycles may require adjustment to prevent the front fender from contacting the engine guard at full fork compression. 1. Check that the top of tube cap on each front-fork slider tube is positioned 0.42 – 0.50 in. (10.7 – 12.7 mm) above the top surface of the fork upper backet. Adjust slider tube position if necessary. See the FRONT FORKS section of your service manual. 2. Remove the highway footpegs and side plates. Retain the footpegs and mounting hardware, including footpeg supports. Discard the side plates and plate-mounting hardware. 3. See Figure 1. Position the engine-guard top mounting plate on the engine-side of the frame upper crossmember. Fasten the guard to the frame using the hardware from this kit as shown. Do not tighten at this time. 4. On each side of the engine guard, insert two socket- head tapping screws with lockwashers from this kit through the two lower mounting holes in the engine- guard lower side plates and into the threaded holes in the frame lower-side bracket. 5. Torque the mounting hardware in steps 2 and 3 to 33 ft- lbs (44.7 Nm).

HARLEY DAVIDSON SISSY BAR UPRIGHT KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 03-02-2011

download
INSTALLATION 1. Install sissy bar upright kit following the appropriate side- plate instruction sheet. 2. If using sissy bar upright with backrest pad, install pad before applying medallion. 3. Clean surface of sissy bar upright using a 50/50 isopropyl alcohol/water solution. Allow surface to dry thoroughly before continuing. NOTES Test placement of medallion on sissy bar upright before installation. Do not remove adhesive backing until ready to apply. The ideal temperature should be at least 60° F (16° C) for proper adhesion of the medallion on the sissy bar upright. 4. Peel off adhesive backing on bar and shield logo medallion (1) and apply to sissy bar upright (2). Press firmly in place for 10 to 15 seconds. 5. Allow the adhesive to cure for 12 hours at no less than 60° F (16° C). 6. Refer to appropriate sideplate instruction sheet for torque specifications. SERVICE PARTS

HARLEY DAVIDSON SOFTAIL TRANSMISSION TOP-COVER KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 03-02-2011

download
INSTALLATION – TOP COVER 1. See Figure 3. Remove and retain the stock screw (J) from the top of the transmission upper cover (I). 2. Ease the left side of the cover through the right side of the engine. You may need to angle the transmission cover slightly as you work it into position. 3. Fasten the weld-nut end of the top-cover bracket (2) to the top cover (4) using the screw (3) from the kit. Torque the screw to 6.6 – 9 ft-lbs (8.9 – 12.2 Nm). 4. Fasten the top of the top-cover bracket (2) to the left side of the transmission upper cover using the screw (J) removed in step 1. Torque the screw to 8 – 10 ft-lbs (10.8 – 13.5 Nm). 5. Install the Softail transmission-interface cover (D). Go to the next section in this instruction sheet. NOTE Save the washer (1) from this kit for transmission-interface cover installation. INSTALLATION – INTERFACE COVER 1. See Figure 1. Remove the screw (1) from interface cover at location 1. Keep the screw for installation. 2. Loosen the screw (2) at location 2 approximately three turns. 3. See Figure 2. Position the slotted hole (1) on the interface- cover mounting bracket (2) behind the washer at location 2. 4. Install the screw (4) from Step 1 through the mounting hole on the bracket and into location 1. Tighten the screw to 7 – 9 ft-lbs (9.5 – 12 Nm). 5. Tighten the screw (3) in location 2 to 13-16 ft-lbs (17.6 – 21.7 Nm). 6. See Figure 3. Place the interface cover (D) in position on the motorcycle. Spread the oil-line grommet (E) to wrap around the oil lines, then re-position the grommet in the interface cover. The edge of the interface cover must overlap the top of the top cover

Incoming search terms: