1999 – 2001 TOYOTA 4Runner UNINTENDED POWER REAR WINDOW ACTIVATION

0

Filed Under (Toyota Manuals) by admin on 13-10-2011

download
or accidental rear window activation. In order to address these concerns, an updated Back Door ECU and Wireless Transmitter have been adopted. 1999 – 2001 model year 4Runners with factory keyless entry systems. MODEL PLANT STARTING VIN ENDING VIN REPAIR PROCEDURE 4Runner V64WD Tahara JT3HN8#R#X0194234 JT3HN8#R#10338020 1 & 2 V6 4WD JT3HN8#R#10338021 JT3HN8#R#10353976 1 Only Hino JT3HN8#R#X9018626 JT3HN8#R#19050479 1 & 2 JT3HN8#R#19050480 JT3HN8#R#19056468 1 Only 4Runner V62WD Tahara JT3GN8#R#X0092242 JT3GN8#R#10194008 1 & 2 V6 2WD JT3GN8#R#10194009 JT3GN8#R#10211000 1 Only NOTE: Please determine where the vehicle falls in VIN range above, and order ONLY the parts associated with the Repair Procedure number(s) listed. (Please refer to the “Parts Information” section on page 2 of this bulletin.

1990- 1995 TOYOTA 4RUNNER BODY LIFT KIT INSTALLATION INSTRUCTIONS KIT

0

Filed Under (Toyota Manuals) by admin on 22-09-2011

Download
Disconnect both battery cables. Disconnect negative cable first, then positive cable Disconnect and move radiator out of the way. . Remove overflow hose from radiator spout. b. Remove four bolts securing radiator to core sup-port. c. Lift radiator up out of slots in core support. d. Straighten tabs on radiator. e. Lay radiator on fan while lifting body. 3. Relocate alternator ground strap if equipped Adhere to recommendations when replacement fasten-
ers, retainers and keepers are called out in the factory service manual. When re-assembling the vehicle it is recommended by the vehicle manufacturer that certain fasteners are replaced in order to maintain proper
retention characteristics. This system may not include all replacement hardware as recommended by the fac-
tory service manual. Additional replacement hardware should be obtained prior to installation of this system to
meet the requirements of the factory service manual.

Dual Battery Installation for 1985 Toyota 4Runner

0

Filed Under (Toyota Manuals) by admin on 16-09-2011

Download
I reviewed a number of locations on my 4Runner including the engine bay, under the body
and rear cargo area. Of all those areas, I decided on the engine bay as the most convenient,
the safest location and the easiest to wire and protect the batteries. Careful measurement of
the OEM battery location showed that by rotating the OEM battery 90 degrees, another
battery could be shoehorned in with some minor modifications. See figure 1 for a photo of
the OEM battery location.
The first problem to solve when mounting batteries in this location is to move the OEM fuse
box approximately 1” towards the rear of the truck. See figure 2 on how I was able to move
my fuse box 1” inch. There is just enough slack in the factory wiring harness to make this
move without having to redo wiring harnesses or putting undo pressure or tension on the
harness

1990- 1995 TOYOTA 4RUNNER BODY LIFT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 08-06-2011

Download
Remove clip holding hydraulic clutch line to support on passenger side firewall. 7. Remove steering shaft from vehicle. a. Mark lower steering shaft where it connects to steering gearbox to insure proper realignment during installation. b. Remove bolt attaching steering shaft to universal joint under dash inside cab. c. Remove bolt attaching steering shaft to gearbox. d. Slide steering shaft up into universal joint and off gear box. e. Slide steering shaft down and out of universal joint and through firewall plate. f. Remove steering shaft from vehicle

TOYOTA 4RUNNER SR5 SUSPENSION INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 31-05-2011

Download
FRONT OF 4RUNNER/FJ CRUISER 1. Park vehicle on level concrete surface. 2. Center and lock the steering wheel.
3. Block the rear wheels of the vehicle to prevent vehicle from moving in either direction. 4. Before lifting vehicle, remove rear shock absorbers and discard. 5. Jack up the vehicle from the lift point in Figure A. 6. Support the vehicle with jack stands from the points in Figure A. 7. Remove the front wheels. 8. Remove sway bar end links from spindle using 17mm socket (both sides). See Figure B. 9. Remove front skid plate using 12mm socket. 10. Remove sway bar from frame using 14mm socket. See Figure C. 11. Using 19mm socket, remove lower bolt and nut from the bottom of the strut (both sides). 12. Remove cotter key and 19mm nut from outer tie rod end, rack &
pinion utilizing a tie rod end puller (or pickle fork). 13. Remove the three nuts (14mm) from the top of the strut. See Figure D. 14. Remove the struts from the vehicle, making sure that they are marked driver and passenger side respectively for reinstallation.