TOYOTA TACOMA 2008 – INTERFACE KIT FOR IPOD REPAIR

0

Filed Under (Toyota Manuals) by admin on 01-11-2011

download
Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this accessory should follow approved guidelines to ensure a quality installation. These guidelines can be found in the “Accessory Installation Practices” document. This document covers such items as: • Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.). • Safety (eye protection, rechecking torque procedure, etc.). • Vehicle Disassembly/Reassembly (panel removal, part storage, etc.). • Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.). Please see your Toyota dealer for a copy of this document. 1. Vehicle Protection. (a) Place driver seat in mid position. (b) Set emergency brake. (c) Remove the negative battery cable. (Fig. 1-1) (1) Protect the fender before starting. CAUTION: Do not touch the positive terminal with any tool when removing cable. (d) Using protective blankets cover front seats, interior of vehicle and center console and front side of the shift lever. (e) Wait 90 seconds before proceeding to disassemble vehicle. 2. Disassembly of Vehicle. NOTE: Place all removed parts on a protected surface. NOTE: When disconnecting wiring connectors, do not pull on the wiring; pull on the connector only. (a) Remove air conditioning control assembly (L,R). (Fig. 2-1) (1) Apply protective tape. (2) Using a panel remover, disengage the four (4) clips and remove the air conditioning control assembly

Incoming search terms:

TOYOTA TACOMA 2009 – SIRIUS SATELLITE RADIO TUNER Preparation

0

Filed Under (Toyota Manuals) by admin on 25-10-2011

download
Vehicle Protection (a) Place driver seat in mid position. (b) Set emergency brake. (c) Remove the negative battery cable. (Fig. 1-1) (1) Protect the fender before starting. CAUTION: Do not touch the positive terminal with any tool when removing cable. (d) Using protective blankets cover front seats, interior of vehicle and center console and front side of the shift lever. (e) Wait 90 seconds before proceeding to disassemble vehicle. 2. Disassembly of Vehicle (a) Remove front floor footrest. For Access Cab (1) Disengage the two (2) clips and remove the front floor footrest. (Fig. 2-1) (b) Remove front door scuff plate LH. For Access Cab (1) Disengage the nine (9) claws and clip, and remove the front door scuff plate

TOYOTA TACOMA 2005 BED EXTENDER Procedure

0

Filed Under (Toyota Manuals) by admin on 24-10-2011

download
Install Mounting Brackets. (a) Follow the Installation Procedures and be careful not to scratch the vehicle. (b) During installation, always wear safety glasses. (c) Bracket installation. (1) Carefully remove the lamp assemblies (Fig. 1-1). (2) Remove the Toyota ’05 Tacoma “D” pillar drilling templates from the bracket kit. Fold or cut on the dashed lines as described on the template. (3) Align the right side template to the right side “D” pillars as described on the template (Fig. 1-2). (4) Using the center punch, carefully mark the center of the three mounting holes thru the template onto the sheet meta

Incoming search terms:

TOYOTA TACOMA 2005 SPARE TIRE LOCK Procedure

0

Filed Under (Toyota Manuals) by admin on 21-10-2011

download
1. Lower Spare Tire. (a) Lower spare tire using hooked jack handle supplied in the vehicle tool kit. 2. Install Spare Tire Lock. (a) Install the spare tire lock assembly on the lowering screw by lining up the cross pin in the lock with the slot in the lowering screw. (b) Tap lock in place with a rubber mallet until it is fully seated. (Pull on lock to ensure attachment.) (c) Install adapter shroud (protects cable and spring) using slotted washer. (See Fig. 2-1) 3. Install Key on Hooked Jack Handle. (a) Install key on hooked jack handle, pressing the jack handle into the slot in the key until the clip snaps in place

Incoming search terms:

TOYOTA Tacoma 2005 – STAINLESS STEEL EXHAUST TIP Procedure

0

Filed Under (Toyota Manuals) by admin on 18-10-2011

download
Safety (eye protection, rechecking torque procedure, etc.).  Vehicle Disassembly/Reassembly (panel removal, part storage, etc.).  Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.). Please see your Toyota dealer for a copy of this document. 1. Installation. (a) Make sure the vehicle’s tail pipe is free from dirt and debris. (b) Remove exhaust tip from box and set on a soft surface to prevent scratching. (c) Slide the Stainless Steel clamp over the vehicle tailpipe as shown. (Fig 1-1 & 1-2) (1) Locate the bolt of the clamp on the right side (3:00 Position) with the nut on the top as shown. (Fig 1-1) (2) Continue sliding up out of the way so it won’t interfere when you install the exhaust tip and aluminum bushing. (Fig. 1-2) (d) Slide the exhaust tip over the tail pipe with the bump facing toward the rear of the vehicle as shown. (Fig 1-3) (1) If necessary, a rubber mallet may be used to aid installation

TOYOTA TACOMA 2005 D RING CARGO TIE DOWN Procedure

0

Filed Under (Toyota Manuals) by admin on 14-10-2011

download
Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this accessory should follow approved guidelines to ensure a quality installation. These guidelines can be found in the “Accessory Installation Practices” document. This document covers such items as:- — Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.). — Safety (eye protection, rechecking torque procedure, etc.). — Vehicle Disassembly/Reassembly (panel removal, part storage, etc.). — Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.). Please see your Toyota dealer for a copy of this document. 1. Hole Placement – Left Side (a) Measure vertically 70 mm up from bottom of truck bed, using marking pencil draw a small horizontal line. (Fig. 1-1) (b) Horizontally measure 72 mm from the front of truck bed, using marking pencil draw a vertical line. (Fig. 1-1) (c) Set drill stop at 1″ from drill tip. (d) Use a center punch to mark the intersection of the two lines and drill a 7/16″ hole as shown in Fig. 1-1. NOTE: Illustration is for long bed, D-cab short bed uses the same process. 2. D-ring Assembly Preparation Left Side (a) Insert the D-ring Assembly into the previously drilled hole. (b) Hold the D-ring Assembly in place by using a strip of duct tape.

Toyota Tacoma Truck – 2010 Performance & Specifications

0

Filed Under (Toyota Manuals) by admin on 28-09-2011

download

Toyota strives to build vehicles to match customer interest and thus they typically are built with popular options and option packages. Not all options/packages are available separately and some may not be available in all regions of the country. If you would prefer a vehicle with no or different options, contact your dealer to check for current availability or the possibility of placing a special order. Toyota Tacomas are designed to meet most off-road driving requirements. Abusive use may result in bodily harm or damage. Toyota encourages responsible operation to protect you, your vehicle and the environment. Some vehicles are shown with available equipment. Seatbelts should be worn at all times. Please do not allow passengers to ride in the cargo area. Towing hitch receivers/ball mount kits are not intended to provide crash protection. For details on vehicle specifications, standard features and available equipment in your area, contact your Toyota dealer. A vehicle with particular equipment may not be available at the dealership. Ask your Toyota dealer to help locate a specifically equipped vehicle. All information presented herein is based on data available at the time of posting, is subject to change without notice and pertains specifically to mainland U.S.A. vehicles only

Incoming search terms:

TOYOTA TACOMA (ALL 4WD, 2WD PRERUNNER, & 2WD TRD MODELS) 3" SUSPENSION LIFT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 27-09-2011

download
Before Starting Installation 1. Carefully read all warnings and instructions completely before beginning. 2. Verify all parts have been received in this kit by checking the parts list at the end of this document. 3. Only install this kit on the vehicle for which it is specified. If anytime during the installation you encounter something different from what is outlined in the instructions, call technical support at (928) 636-3175. 4. Special tools needed: a. Coil spring compressor 5. Park vehicle on a clean, dry, flat, level surface and block tires so vehicle cannot roll in either direction. Ride Height 1. Measure ride height with the vehicle supporting its own weight on level ground. To settle the suspension, the vehicle should be driven forward at least 10 feet immediately prior to taking these measurements. Ride height is the measurement from the NOTE Kit parts are prefaced by the word kit and appear in bold print. NOTE Adhere to recommendations when replacement fasteners, retainers and keepers are called out in the factory service manual. When re-assembling the vehicle it is recommended by the vehicle manufacturer that certain fasteners are replaced in order to maintain proper retention characteristics. This system may not include all replacement hardware as recommended by the factory service manual. Additional replacement hardware should be obtained prior to installation of this system to meet the requirements of the factory service manual

Incoming search terms:

TOYOTA TACOMA BODY LIFT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 22-09-2011

download
Disconnect both battery cables. Be sure to disconnect the negative cable first, then the positive cable. Remove
the airbag fuse from the fuse box. 4. Remove the wire loom that runs from under the alternator to the battery from the mounting brackets. One bracket is on top of the frame. The other bracket is on the fender well. The plastic mounting-collar will slide off the bracket by pushing on the tab on the collar. 5. Remove the fuse that controls the air bag system from the fuse box (refer to the owners manual for the exact location). 6. Remove the ground wire that runs from the back of the engine to the top of the firewall. Remove the wire loom from the mounting bracket on the firewall. Remove the bracket from the firewall. Turn the bracket upside down. Insert the mounting bolt through the ground wire removed from the firewall, Then through the bracket. Tighten securely. Reinstall the bolt that mounted the ground wire to the firewall. Tighten the bolt securely. Do not attach the wire loom at this time

TOYOTA TACOMA TRANSMISSION TO ATLAS TRANSFER CASE

0

Filed Under (Toyota Manuals) by admin on 20-09-2011

Download
Remove the stock transfer case from the stock tailhousing adapter. The stock tailhousing is retained along with the stock rubber crossmember support. Once the transfer case is removed, you’ll see a seal located in the stock tailhousing. This seal must be removed and discarded. Some tailhousings also had a bearing which also must be removed. Install the new oil seal into the large end of the seal adapter. The sealing lip should be facing down. The small end of the seal adapter has the same O.D. (outside diameter) as the old seal that was just removed from the stock tailhousing. The seal adapter is a press-fit into the stock tail and should now be installed. The kit comes with a new spud shaft which fits over the stock Toyota transmission 26 spline output shaft. This spud shaft has a Jeep 23 male spline on the opposite side which fits into a standard 23 spline Atlas case. When installing the spud shaft into the Toyota transmission, the spud shaft does not seal onto the new seal just previously installed. The seal contacts seal off of the Atlas input shaft. The adapter plate should now be installed onto the Atlas transfer case. The adapter plate indexes off of the Atlas front retainer

Incoming search terms:

Incoming search terms: