TOYOTA TACOMA 2005 BED EXTENDER Procedure

0

Filed Under (Toyota Manuals) by admin on 24-10-2011

download
Install Mounting Brackets. (a) Follow the Installation Procedures and be careful not to scratch the vehicle. (b) During installation, always wear safety glasses. (c) Bracket installation. (1) Carefully remove the lamp assemblies (Fig. 1-1). (2) Remove the Toyota ’05 Tacoma “D” pillar drilling templates from the bracket kit. Fold or cut on the dashed lines as described on the template. (3) Align the right side template to the right side “D” pillars as described on the template (Fig. 1-2). (4) Using the center punch, carefully mark the center of the three mounting holes thru the template onto the sheet meta

Incoming search terms:

TOYOTA Tacoma 2005 – STAINLESS STEEL EXHAUST TIP Procedure

0

Filed Under (Toyota Manuals) by admin on 18-10-2011

download
Safety (eye protection, rechecking torque procedure, etc.).  Vehicle Disassembly/Reassembly (panel removal, part storage, etc.).  Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.). Please see your Toyota dealer for a copy of this document. 1. Installation. (a) Make sure the vehicle’s tail pipe is free from dirt and debris. (b) Remove exhaust tip from box and set on a soft surface to prevent scratching. (c) Slide the Stainless Steel clamp over the vehicle tailpipe as shown. (Fig 1-1 & 1-2) (1) Locate the bolt of the clamp on the right side (3:00 Position) with the nut on the top as shown. (Fig 1-1) (2) Continue sliding up out of the way so it won’t interfere when you install the exhaust tip and aluminum bushing. (Fig. 1-2) (d) Slide the exhaust tip over the tail pipe with the bump facing toward the rear of the vehicle as shown. (Fig 1-3) (1) If necessary, a rubber mallet may be used to aid installation

TOYOTA TACOMA 2005 D RING CARGO TIE DOWN Procedure

0

Filed Under (Toyota Manuals) by admin on 14-10-2011

download
Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this accessory should follow approved guidelines to ensure a quality installation. These guidelines can be found in the “Accessory Installation Practices” document. This document covers such items as:- — Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.). — Safety (eye protection, rechecking torque procedure, etc.). — Vehicle Disassembly/Reassembly (panel removal, part storage, etc.). — Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.). Please see your Toyota dealer for a copy of this document. 1. Hole Placement – Left Side (a) Measure vertically 70 mm up from bottom of truck bed, using marking pencil draw a small horizontal line. (Fig. 1-1) (b) Horizontally measure 72 mm from the front of truck bed, using marking pencil draw a vertical line. (Fig. 1-1) (c) Set drill stop at 1″ from drill tip. (d) Use a center punch to mark the intersection of the two lines and drill a 7/16″ hole as shown in Fig. 1-1. NOTE: Illustration is for long bed, D-cab short bed uses the same process. 2. D-ring Assembly Preparation Left Side (a) Insert the D-ring Assembly into the previously drilled hole. (b) Hold the D-ring Assembly in place by using a strip of duct tape.

TOYOTA TACOMA 2005 SUPERCHARGER FIT KIT

0

Filed Under (Toyota Manuals) by admin on 27-09-2011

download
are must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this accessory should follow approved guidelines to ensure a quality installation. These guidelines can be found in the “Accessory Installation Practices” document. This document covers such items as:- • Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.). • Safety (eye protection, rechecking torque procedure, etc.). • Vehicle Disassembly/Reassembly (panel removal, part storage, etc.). • Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.). • The TIS Repair Manual can be referenced for additional details. Please see your Toyota dealer for a copy of this document. 1. Installation Review and Vehicle Preparation. (a) Review the entire instruction instructions provided before beginning the installation (b) Review the parts list/kit contents to ensure that all parts are present before beginning the installation. If any items are missing contact Technical Support at (800) 688-5912 before proceeding. (c) Remove any low-octane fuel from the vehicle. Ensure that ONLY 91 octane or higher unleaded gasoline is used. (d) Place the vehicle onto vehicle hoist. (e) Protect the vehicle with protection blankets over the fenders and front of the vehicle. (f) Disconnect and remove the battery. (g) When draining the cooling system into a clean container in Step 7

Incoming search terms: