HARLEY DAVIDSON COMBINATION SPEEDOMETER/TACHOMETER GAUGE KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 17-04-2011

download
Removing the Old Speedometer NOTE This Instruction Sheet covers several different Harley- Davidson models and years. Make sure you locate and follow the procedures that apply to the motorcycle receiving the new gauge. 1. Apply power to motorcycle and record the odometer reading. 2. Remove the seat according to the procedure in the applicable Service Manual. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative cable first) before proceeding. (00048a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 2. Disconnect battery cables, negative cable first. NOTE Cover the fuel tank with clean shop towels to prevent scratching. Damage to the finish could result. 3. Remove the instrument console acorn nut (and mounting screw with a flat washer on some models). Lay clean shop towels on the fuel tank. Lift the console from the fuel tank, turn it upside down and lay it on the towels. NOTE If necessary, bend back the flexible metal clip to free the harness conduit from the underside of the console. 4. Unplug the 12-terminal connector (39B) from the back of the speedometer. Depress the external latches and use a rocking motion to separate the pin and socket halves. 5. Remove the back clamp: All models except FXSTD: Gently pry the three latches upward to release the back clamp from the back of the speedometer. FXSTD: Depress the three external legs of the lock ring, then gently pry the three latches upward to release the back clamp from the back of the speedometer. 6. Unscrew the trip-meter reset button, and pull the harness from the clamp (remove the screw if necessary). 7. Lift the console and remove the old speedometer from the console. Discard the old speedometer, but retain the rubber gasket and back clamp for use with the new gauge. NOTE Set the console securely on the towel-covered fuel tank, and take care that it doesn’t fall off during the following opera- tions. 8. Set the console securelyon the fuel tank. Installation and Final Check NOTE Apply window cleaning fluid or mild soapy water to the speedometer gasket as needed to aid installation. 1. Turn the console over, facing upward. 2. Place the speedometer gasket into position around the console speedometer bore. 3. Fit the new gauge into the bore so that it fits snugly against the rubber gasket. Rotate the gauge into approximate visual alignment. The back clamp will complete the alignment. 4. Turn the console over, face down. 5. Install the back clamp

Incoming search terms:

HARLEY DAVIDSON CHROME CONSOLE KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 04-02-2011

download
Installation 1. See Figure 1. Remove and discard the two 1-1/4 in. (32 mm) long hex socket button-head screws (3) that secure the original console (1) to the fuel tank. 2. Remove and retain the 5/8 in. (16 mm) long hex socket button-head screw (4) securing the rear of the console to the rear of the tank. Lift the console and edging trim (2) from the motorcycle. 3. Lay clean shop towels on the fuel tank, flip the console over to expose the underside and lay it on the towels. 4. Unscrew the trip-meter reset button (12) and pull the reset switch (11) from the console opening. 5. Depress the connector tab and remove the 12-place connector [39B] (10) from the back of the speedometer (9). Depress the connector tab and remove the 12-place connector [108B] (7) from the back of the tachometer (6). 6. Remove and retain the four screws (14) and back clamp (13) from the speedometer and tachometer. 7. Turn the console over, face upward. NOTE When removing the speedometer and tachometer from the console, the gaskets may remain on the instruments. If this is the case, carefully remove them from the instruments for re-assembly to the new console. 8. Remove the speedometer and tachometer from the console (1). Carefully remove the gaskets (8) from the instruments. Move the console away from the vehicle. 9. Obtain the new Chrome console from the kit. Place the console on the shop towel-covered fuel tank NOTE Apply window cleaning fluid or mild soapy water to the instrument gaskets as needed to aid installation. 10. Place the speedometer gasket into position around the console speedometer (forward) bore. Fit the gauge into the bore so that it fits snugly against the rubber gasket. Rotate the gauge into approximate visual alignment. The back clamp will complete the alignment.

Incoming search terms:

DUCATI MONSTER 696 Owner's manual and maintenance manual

0

Filed Under (Ducati) by admin on 14-12-2010

download
instrument panel (fig. 4) 1) LCD (see page13). 2) Tachometer (rpm). Indicates engine revs per minute. 3) Neutral (N) indicator ( green ). Illuminates when the gearbox is in neutral. 4) Fuel warning light ( yellow ). Illuminates when there are approximately 3litres of fuel left in the tank. 5) Turn signal indicator light ( green ). Illuminates and flashes when the turn signal is in operation. 6) Engine oil pressure warning light ( red ). Illuminates when engine oil pressure is too low. This light should illuminate when the ignition is switched to ON and should go out a few seconds after the engine starts. Important If this light (6) stays on, stop the engine to avoid serious damage. 7) High beam warning light ( blue ). Illuminates when the high beam headlight is on. 8) “EOBD engine diagnostics light” ( amber ). The engine ECU iluminates this light steadily to indicate the presence of errors leading to engine lock. 9) OVER REV indicator lights . Illuminates steadily at 800 rpm before intervention of the revlimiter. Starts flashing when the rev limiter is reached. 5 8 2 4 9 3 1 6 7 fig. 4 12 E 10) 2-position switch A and B . Switch used for displaying and setting instrument panel parameters. It has two positions, A “▲” and B “▼”. 11) High beam headlight flasher switch (fig. 5). The high beam headlight flasher switch is also used for the LAP and USB data aquisition functions. 11 A 10 B fig. 5 13 E LCD – Main functions Warning Any adjustments to the instrument panel must only be carried out when the motorcycle is stationary. Never operate the instrument panel controls while riding the motorcycle. 1) Speedometer . Indicates road speed. 2) Odometer . Shows total distance travelled. 3) Trip meter . Indicates the distance travelled since last reset. 4) Fuel reserve trip counter . Shows distance travelled on reserve fuel. 5) Clock . 6) Air temperature indicator . 7) Lap time . 8) Rev counter (RPM) . 9) Lap time . 8 11 13 12 14 10 4 5 9 6 2 3 1 7 fig. 6 14 E 10) Service indicator (fig. 6). The indicator illuminates to signal when a service is due. The service indiactor will remain on the display until the system is reset by the Ducati Service Centre who carry outthe service. 11) LAP function (fig. 6). Indicates that the LAP has been activated. 12) DDA function (fig. 6). Indicates that the Ducati Data Analyzer (DDA) has been activated. Important The instrument panel incorporates diagnostic functions for the electronic injection/ignition system. The relative menus are for the use of trained personnel only. If you accidentally access this function, turn the key to OFF and have the motorcycle checked at an authorised Ducati Service Centre. 13) Oil temperature indicator (fig. 6). Important Stop riding if the temperature reaches the maximum value, otherwise the engine might be damaged. 14) Ducati Traction Control (DTC) (fig. 6). Indicates activation of the DTC control unit (if present). 15 E LCD – How to set/display parameters At key-on (key turned from OFF to ON ) the instrument panelactivates all the digits of the LCD for 1second and switches on the indicator lights in sequence.

Incoming search terms:

DUCATI MONSTER 1100 / 1100S Owner's manual and maintenance manual

0

Filed Under (Ducati) by admin on 14-12-2010

download
1) Speedometer . Indicates road speed. 2) Odometer . Shows total distance travelled. 3) Trip meter . Indicates the distance travelled since last reset. 4) Fuel reserve trip counter . Shows distance travelled on reserve fuel. 5) Clock . ) Lap time . 7) Rev counter (RPM) . 8) Lap time . 7 10 12 11 13 9 4 5 8 2 3 1 6 fig. 6 14 E 9) Service indicator (fig. 6). The indicator illuminates to signal when a service is due. The service indicator will remain on the display until the system is reset by the Ducati Service Centre whocarry outthe service. 10) LAP function (fig. 6). Indicates that the LAP has been activated. 11) DDA function (fig. 6). Indicates that the Ducati Data Analyzer (DDA) has been activated. Important The instrument panel incorporates diagnostic functions for the electronic injection/ignition system. The related menus are for use by trained personnel only. If you accidentally access this function, turn the key to OFF and have the motorcycle checked at an authorized Ducati Service Centre. 12) Oil temperature indicator (fig. 6). Important Stop riding if the temperature reaches the maximum value, otherwise the engine might be damaged. 13) Ducati Traction Control (DTC) (fig. 6). Indicates activation of the DTC control unit (if present). 15 E LCD – How to set/display parameters At key-on (key turned from OFF to ON ) the instrument panelactivates all the digits of the LCD for 1second and switches on the indicator lights in sequence. OFF CHECK 1 fig. 7 16 E It then reverts to “normal” mode and, in place of the motorcycle speed, shows the model and, for 2 seconds, alsothe version (EU, UK, USA, CND, FRA, JAP). The model is scrolled on the display onceonly. CHECK 2 RUN fig. 8 17 E At Key-On, the instrument panel always shows the following information (de-activating any previously activated functions): Odometer Speed Engine rpm bargraph Engine oil temperature bargraph At this point, with button (1, fig. 9) in position B “▼” it is possible to switch from the odometer display function to thefollowing functions: TRIP TRIP FUEL (only if active) Clock before returning to TOT (odometer function). If, however, you press switch (1, fig. 9) in position A “▲”, thesystem enters MENU mode and displays the following functions in sequence: Error (only if active) BATT RPM LIGHT SET LAP (OFF or ON) LAP MEM DDA (OFF or ON) Erase DDA TIME Set CODE (only if active)

Incoming search terms:

Triumph T595 Daytona and T509 Speed Triple Specifications

0

Filed Under (Triumph) by admin on 06-11-2010

download
1. Tachometer 8. Turn Indicator light 2. Tachometer ‘Red Zone’ 9. Low Oil Pressure Warning Light 3. Speedometer 10. High Beam Indicator Light 4. Odometer 11. Neutral Indicator Light 5. Trip Meter 12. Low Fuel Level Indicator Light 6. Trip Meter Reset Knob 13. Engine Management Malfunction 7. Coolant Temperature Gauge Indicator Light SPEEDOMETER The speedometer indicates the road speed of the motorcycle. In the speedometer face are the odometer and trip meter. The odometer shows the total distance that the motorcycle has travelled. The trip meter shows the distance travelled since the meter was last reset to zero. The trip meter can be reset to zero by rotating the reset knob situated on the left hand side of the speedometer. TACHOMETER The tachometer shows the engine speed in revolutions per minute – rpm (r/min). On the right side of the tachometer face is the ‘red zone’. Engine rpm (r/min) in the red zone is above maximum recommended engine speed and is also above the range for best performance. / f&it. ::;:%M,to %:th:’z zone as severe engme damage may NOTE The ‘Red Zone’ position for Daytona is different to that on the Speed Triple. Page 16
General Information COOLANT TEMPERATURE GAUGE The coolant temperature gauge indicates the temperature of the engine coolant. On the right -hand side of the gauge face is the ‘red zone. If the temperature gauge needle moves into the ‘red zone’ this indicates that the engine is overheating. needle enters the ‘red zone’ as severe WARNING LIGHTS I a0 INDICATORS When the indicator switch is turned to left or right, the corresponding direction indicator light flashes on and off. cl ~ LOW OIL PRESSURE: The low oil pressure warning light becomes illuminated whenever the oil pressure is dangerously low (or the ignition switch is in the ‘ON’ position with the engine not running). When the engine is running, the light will remain off when sufficient oil pressure is present. When starting the motorcycle, check that the light comes on when the ignition is in the ‘ON’ position, but goes out as soon as the engine starts A! CAUTION: Stop the engine immediately if the low oil pressure warning light comes on during normal operation. Do not restart the engine until the fault has been rectified. Severe engine damage will result from running the engine when the oil warning light is illuminated. HIGH BEAM: When the headlights are switched on and the headlight dip switch is set to ‘high beam’, the high beam warning light will illuminate. IElI NEUTRAL: The neutral warning light indicates when the transmission is in neutral (no gear selected). The warning light will illuminate when the transmission is in neutral with ignition switch in the ‘ON’ position. ml LOW FUEL: The low fuel indicator will illuminate when there are approximately 3.7 litres of fuel remaining in the tank. Et3 ENGINE MANAGEMENT SYSTEM MALFUNCTION INDICATOR LIGHT: The malfunction indicator light for the engine management system illuminates when the ignition is switched on, remains illuminated during starting, and goes out shortly after the engine starts. If the malfunction indicator light becomes illuminated during riding, a fault has occurred in the engine management system. In this case the system will switch to ‘limp-home’ mode so that riding may continue. Contact an authorised Triumph dealer as soon as possible to have the fault checked out and rectified

Incoming search terms:

Incoming search terms: