YAMAHA RX10H/ RX10SH RX10MH/ RX10MSH/ RX10RH/ RX10RSH SERVICE AND OWNER’S MANUAL

0

Filed Under (Yamaha) by admin on 27-04-2011

download
Throttle override system (T.O.R.S.) If the carburetor or throttle cable should malfunction during operation, the T.O.R.S. will operate when the throttle lever is released. The T.O.R.S. is designed to interrupt the ignition and keep the engine revolution speed between 2,800 and 3,000 r/min if the carburetor fails to return to idle when the lever is released. Speedometer unit The speedometer unit is equipped with the following: a digital speedometer (which shows riding speed) an odometer (which shows the total distance traveled) a tripmeter (which shows the distance traveled since it was last set to zero) warning indicators (which show self-diagnosis, cool ant temperature, fuel level, and oil level warnings) fuel meter (which shows the fuel remaining in the fuel tank) grip/thumb warmer heat level indicator  (which shows the heat level of the grip warmer or the thumb warmer) After the engine is started, the tachometer 1 makes one sweep, and the warning light 2 and all segments of the meter 3 turn on and off once. Then the warning light turns on again, and then goes off if there are no problems. The grip warmer heat level is initially displayed for 5 seconds, then switches to the fuel meter display. Odometer and tripmeter modes Pushing the select/reset button 4 switches the display between the odometer mode “ODO” and the tripmeter mode “TRIP”. To reset the tripmeter, push the select/reset button for at least one second while the tripmeter is displayed. NOTE: @ To switch the speedometer, odometer, and tripmeter displays between kilometers and miles, select the odometer mode “ODO”, and then push the select/reset button 4 for at least 10 seconds. ESU00363 High beam indicator light The high beam indicator light 1  comes on when the high beams of the headlights are switched on. (See page 5-12 for headlight beam switch operation.)

2003 Honda ST1300lA OWNER'S MANUAL

0

Filed Under (Honda) by admin on 24-04-2011

download
Gauges & Indicators Lights when engine oil pressure is low enough to cause engine damage. If the indicator lights, pull safely to the side of the road. See page 162 for instructions and cautions. Lamp Check. PGM-FI malfunction indicator lamp (red) low oil pressure indicator (red) Lights when there is any abnormality in the PGM-FI (Programmed Fuel Injection) system. Should also light for a few seconds and then go off when the ignition switch is turned ON and the engine stop switch is at RUN. If the indicator comes on at any other time, reduce speed and take your motorcycle to a Honda dealer as soon as possible. Lamp Check. anti-lock brake system (ABS) indicator (red) ABS (ST 1300A) Lights when there is any abnormality in the anti-lock brake system (ABS). Normally, this indicator comes on when the ignition switch is turned ON, and goes off after you ride the motorcycle at a speed above 6 mph (10 km/h)If the indicator comes on while riding, stop the motorcycle in a safe place and turn off the engine. Refer to ABS indicator, page 61. For information about ABS, see page 60. LampCheck Use this button for the following purposes. To adjust time To adjust display illumination Use this button for the following purposes. To adjust time To select and reset the fuel mileage meter To change the mileage units for the odometer/tripmeter and available driving distance Use this button for the following purposes. To adjust time To select and reset the tripmeter

YAMAHA XV1700 PCR/ XV1700 PCRC OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 02-12-2010

download
High beam indicator light “” 2. Right turn signal indicator light “” 3. Fuel level warning light “” 4. Engine trouble warning light “” 5. Left turn signal indicator light “” 6. Neutral indicator light “” 1. Speedometer INSTRUMENT AND CONTROL FUNCTIONS 3-4 3 EAU04436 Tachometer unit The electric tachometer allows the rider to monitor the engine speed and keep it within the ideal power range. The tachometer unit is equipped with the following: ● an odometer (which shows the total distance traveled) ● two tripmeters (which show the distance traveled since they were last set to zero) ● a fuel reserve tripmeter (which shows the distance traveled since the fuel level warning light came on) ● a meter lighting control ● a clock ● a self diagnosis device NOTE: ● Be sure to turn the key to “ON” before using the “SELECT” and “RESET” buttons. ● To switch the odometer, the trip- meters and the fuel reserve trip- meter displays between kilometers and miles, press the “SELECT” button for at least two seconds. ECA00123 CAUTION: Do not operate the engine in the tachometer red zone. If operated in the red zone, the tachometer segments will start flashing to notify the rider. Red zone: 5,000 r/min and above 1. Tachometer 2. Clock 3. Odometer/tripmeter/fuel reserve tripmeter 4. “RESET” button 5. “SELECT” button 1. Tachometer red zone
INSTRUMENT AND CONTROL FUNCTIONS 3-5 3 Odometer and tripmeter modes Pushing the “SELECT” button switches the display between the odometer mode”ODO” and the tripmeter modes “TRIP 1″ and “TRIP 2″ in the following order: ODO→ TRIP 1 → TRIP 2 → ODO If the fuel level warning light comes on (see page 3-2), the odometer display will automatically change to the fuel reserve tripmeter mode “TRIP F” and start counting the distance traveled from that point. In that case, pushing the “SELECT” button switches the display between the various tripmeter and odometer modes in the following order: TRIP F → TRIP 1 → TRIP 2 → ODO → TRIP F To reset a tripmeter, select it by pushing the “SELECT” button, and then push the “RESET” button for at least one second. If you do not reset the fuel reserve tripmeter manually, it will reset itself automatically and the display will return to the prior mode after refueling and traveling 3mi (5km). Meter lighting control mode 1. Turn the key to “OFF”. 2. Push and hold the “SELECT” but- ton. 3. Turn the key to “ON”, and then after five seconds, release the “SELECT” button. 4. Push the “RESET” button to select the desired brightness. 5. Push the “SELECT” button to set the brightness level. 6. Turn the key to “OFF”. NOTE: When adjusting the meter lighting, the odometer display will indicate the brightness level. Clock mode To set the clock: 1. Push the “SELECT” button and “RESET” button together for at least two seconds. 2. When the hour digits start flashing, push the “RESET” button to set the hours. 3. Push the “SELECT” button, and the minute digits will start flashing. 4. Push the “RESET” button to set the minutes. 5. Push the “SELECT” button and then release it to start the clock. NOTE: ● After setting the clock, be sure to push the “SELECT” button before turning the key to “OFF”, otherwise the clock will not be set. ● To set the clock after the battery has been disconnected, first set the time to 1:00 AM, and then set the clock to the correct time

Incoming search terms:

YAMAHA XT500E, XT600E SPECIFICATIONS AND OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 24-11-2010

download
INSTRUMENT AND CONTROL FUNCTIONS 3 ON OFF LOCK . EAU00040 LOCK The steering is locked, and all electrical systems are off. The key can be removed. To lock the steering 1. Turn the handlebars all the way to the left. 2. Push the key in from the “OFF” position, and then turn it to “LOCK” while still pushing it. 3. Remove the key. To unlock the steering Push the key in, and then turn it to “OFF” while still pushing it. 12 1. Push. 2. Turn.
3-2 INSTRUMENT AND CONTROL FUNCTIONS 3 EAU00056 Indicator lights EAU00063 High beam indicator light ” & ” This indicator light comes on when the high beam of the headlight is switched on. EAU00061 Neutral indicator light “N” This indicator light comes on when the transmission is in the neutral position. EAU00057 Turn signal indicator light ” 5 ” This indicator light flashes when the turn signal switch is pushed to the left or right. 12 3 1. High beam indicator light “&” 2. Neutral indicator light “N” 3. Turn signal indicator light “5 ” EAU00095 Speedometer unit The speedometer unit is equipped with a speedometer, an odometer and a tripmeter. The speedometer shows riding speed. The odometer shows the total distance traveled. The tripmeter shows the distance traveled since it was last set to zero with the reset knob. The tripmeter can be used to estimate the distance that can be traveled with a full tank of fuel. This information will enable you to plan future fuel stops