TRIUMPH AMERICA AND SPEEDMASTER SOLO RACK FITS INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 29-01-2011

download
1. Remove the 8mm bolt from the rear of the passenger seat. Remove the passenger seat by pushing the seat forward and lifting up at the front edge of the seat. Remove the 12mm bolt from the rear of the drivers seat. 2. From the supplied hardware locate the two socket head screws and washers, place the large washers onto the screws with the polished side of the washer facing the head of the screws. Place the small screw and washer thru the small hole in the rear of the solo rack, place the black plastic spacer supplied onto the screw on the bottom side of the solo rack. Holding the rack in place on the rear fender, start the screw in the rear hole. Install the remaining large screw with its washer into the front hole and tighten both screws securely.

TRIUMPH AMERICA AND SPEEDMASTER FRONT TURN SIGNAL RELOCATORS

0

Filed Under (Triumph) by admin on 29-12-2010

download
1. Remove the front turn signals as follows. The turn signal wire plugs are located inside the handlebar switch housings. Remove the two Phillips screws located on the forward facing side of the switch housing, remove the covers, unplug the turn signals and reassemble the switch housings. Unbolt the signals from their black mounting brackets, remove the brackets from the bottom side of the switch housings, reinstall the nuts and tighten securely. 2. Disassemble the two halves of the turn signal mounting clamps supplied, place the M6 X 25mm button head screws thru the hole in the side of the clamp from the inside, place the spacers supplied over the screw threads. Screw the clamps and spacers onto the turn signals. Hold the signal/clamp assemblies up to the front fork, position the signals so that the housing/lens seam is vertical and straight, carefully remove the assemblies from the forks and tighten the screws securely. Install the signal/clamps onto the forks, set to the desired height and angle and tighten the clamp screws securely. 3. Using a sharp knife slit the black wire loom from the turn signal plug back 7″. Pull the turn signal wires and plugs out from the loom. Fold the wires along the loom going down towards the headlight. Leave 2-3″ of the wire next to the plug exposed and neatly tape the rest of the wire to the loom and the loom closed back up to the handlebar switch. 4. Connect the signal wires to the plugs from the wire loom. Using the cable ties supplied tie up any loose or unconcealed wire and the plugs.

TRIUMPH AMERICA AND SPEEDMASTER PASSENGER FLOORBOARDS INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 25-12-2010

download
1. Remove the 12mm nuts located behind the stock foot peg assemblies and remove the peg sets. 2. Starting on the left side locate the left floorboard assembly and left round chrome spacer block. These will be stamped with an” L” on the back side. Insert two of the 3/16″ x 1/2″ dowel pins supplied into the two holes where the foot peg was mounted at one o’clock and seven o’clock. Place the spacer blocks backside (stamped with the L) onto the pins 3. Place two more of the dowel pins in the holes on the outside of the block using the holes at twelve o’clock and six o’clock. Place the left floorboard assembly onto the spacer block and pins so that it is parallel to the ground or horizontal (this will be the holes closest to six and twelve o’clock on the backside of the floorboard assembly). Insert one of the 5/16″ x 2″ socket head bolts into the center-mounting hole. Place one of the 5/16″ washers, lock washers and nuts onto the bolt and make finger tight. Recheck to be sure the floorboard is parallel to the ground. 4. On the right side install two more of the dowel pins supplied into holes where the foot peg was mounted at eleven o’clock and five o’clock. Place the remaining spacers backside (stamped with an R) onto the pins 5. Place the remaining two dowel pins supplied into the holes of the spacer block at six o’clock and twelve o’clock. Place the right floorboard assembly onto the spacer block and pins so that it is parallel to the ground or horizontal (this will be the holes closest to six and twelve o’clock on the backside of the floorboard assembly). Insert one of the 5/16″ x 2″ socket head bolts into the center-mounting hole. Place one of the 5/16″ washers, lock washers and nuts onto the bolt and make finger tight. Recheck to be sure the floorboard is parallel to the ground. NOTE; if you are also installing the TA005-5 relocation arms, follow those instructions next. Finally be sure to tighten all bolts securely

TRIUMPH AMERICA AND SPEEDMASTER CALIPER COVER INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 23-12-2010

download
INSTALLATION INSTRUCTIONS CALIPER COVER FOR TRIUMPH AMERICA & SPEEDMASTER #TA030 RIVCO 1. Clean caliper face with rubbing alcohol making sure it is free of grease, oil & debris. 2. If the caliper is below 70 degrees warm it with a hair dryer. 3. Peel the self-adhesive backing and press into place firmly and hold for 30 seconds

Triumph America Installation Manual

0

Filed Under (Triumph) by admin on 29-10-2010

download
Secure motorcycle in an upright position. 2) Remove center stand 3) Remove saddle bags (if applicable) 4) Attach bracket A to center stand mounting point on motorcycle 5) Attach bracket D (left) / E (right) to rear fender sub-frame using new bolts provided. It may be necessary to reattach saddle bags at this point 6) Attach bracket F (left) / G (right) to rear of brackets D/E. 7) Attach bottom of brackets F/G to rear hitch plate. 8) Attach bracket B (left) / C (right) to bottom of forward hitch arms. Attach other end of B/C to top of bracket A. 9) Ensure hitch is square with motorcycle and tighten all bolts. Receiver Hitch Diagram Leveling stand screw jack installation 1) Thread right side screw jack into threaded leveling stand tab on bracket A and adjust leveling jack bolt out. 2) Push motorcycle over from left side until right screw jack is touching floor. 3) Install left side screw jack on bracket A and adjust out until motorcycle will rest upright on both screw jacks. 4) Adjust screw jacks until motorcycle is level. CAUTION – Use screw jacks to hold motorcycle upright and level ONLY. Do not lift motorcycle with screw jacks. CAUTION – Use care when installing screw jacks. Be certain that motorcycle is always in a stable balanced position