TRIUMPH ROCKET III SWING ARM COVER INSTALLION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 29-01-2011

download
1. Locate and remove the 6mm screw which secures the rear brake hose clip to the top of the swing arm (just in front of the lower right shock absorbers mounting point. 2. Notice the double faced adhesive tape on the inside of the cover and where it will contact the swing arm when installed, clean this area with rubbing alcohol and remove the backing from the adhesive tape on the inside of the cover. 3. Place the º” washer provided on the top of the swing arm over the brake hose clip mounting hole. Starting at the rear of the swing arm slide the cover carefully into place and align the small hole in the top of the cover with the washer and the threaded hole. Place the screw thru the hose clip then the cover and finally the washer, next thread the screw into the hole finger tight only. 4. Press the front area of the cover with the adhesive tape firmly into place. Tighten the 6mm brake hose clip screw securely.

TRIUMPH ROCKET III TIP OVER BARS INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 29-12-2010

download
1. Starting on the right side (towards the front of the motor) locate the three mounting bolts that secure the brake assembly bracket (a chrome tube) to the bottom of the motor. Remove the bottom and front bolts. Repeat for left side. 2. Locate the front motor mount bolt. This is the black bolt located at the very front of the engine about halfway down behind the radiator. Remove the nut from this bolt on the left side. Properly secure the bike and use a jack to lift up on the motor to release the pressure from the motor mount bolt. Remove the bolt. 3. On the right side place the motor mount bolt thru the upper mounting hole of the right tip over bar. Install the tip over bar by feeding the motor mount bolt thru the original hole and inserting the two bolts (supplied) into the bottom mounting holes. (Do not tighten yet.) 4. On the left side install the top of the left tip over bar by inserting it into the right side tip over bar. Align the tip over bar so that the motor mount bolt extends thru the upper mounting hole. Thread the original locking nut onto the motor mount bolt a couple of turns. Now align the bottom of the tip over bar and install the remaining two bolts (supplied). Tighten the motor mount bolt (torque to 28-32 ft/lbs) and the lower four bolts (torque to 14-18 ft/lbs) securely. 5. Re-check all hardware for tightness

TRIUMPH ROCKET III SWING ARM COVER INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 28-12-2010

download
1. Locate and remove the 6mm screw which secures the rear brake hose clip to the top of the swing arm (just in front of the lower right shock absorbers mounting point. 2. Notice the double faced adhesive tape on the inside of the cover and where it will contact the swing arm when installed, clean this area with rubbing alcohol and remove the backing from the adhesive tape on the inside of the cover. 3. Place the ¼” washer provided on the top of the swing arm over the brake hose clip mounting hole. Starting at the rear of the swing arm slide the cover carefully into place and align the small hole in the top of the cover with the washer and the threaded hole. Place the screw thru the hose clip then the cover and finally the washer, next thread the screw into the hole finger tight only. 4. Press the front area of the cover with the adhesive tape firmly into place. Tighten the 6mm brake hose clip screw securely.

TRIUMPH ROCKET III CALIPER COVERS INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 26-12-2010

download
1. Clean caliper face with rubbing alcohol making sure it is free of grease, oil and debris. 2. If the caliper is below 70 degrees warm it with a hair dryer. 3. Peel the self adhesive backing and press into place firmly and hold for 30 seconds. 4. Repeat with remaining cover if necessary.

TRIUMPH ROCKET III SOLO RACK INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 24-12-2010

download
1. Using the ignition key remove the driver’s seat. Remove the three bolts which secure the passenger seat to the rear fender and remove the passenger seat. 2. Place the lock washers and washers onto the three 6 x 25mm bolts (supplied). Place the solo rack onto the rear fender and align the bolt holes in the fender with the holes in the solo rack. Starting with the two lower holes, place the black plastic spacers (two supplied) between the fender and the solo rack. Next insert two of the bolts with the washers thru the rack and spacers then thread into the fender several turns. At the upper hole place the rubber washer (supplied) between the solo rack and the fender. Insert the remaining bolt with washers thru the solo rack, rubber washer and thread into the fender. Tighten all three bolts securely. 3. Reinstall driver’s seat.

TRIUMPH ROCKET III DRIVER FLOOR BOARDS INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 24-12-2010

download
1. Starting on the left (shifter) side remove shifter pivot bolt (large allen head). Rotate the shifter assembly out of the way. Remove the retaining clip from the bottom of the foot peg pivot pin. Remove the pin and the foot peg. 2. Install the left floorboard in the original foot peg mounting location. (Note the L & R markings on the backside of the mounting blocks.) Place the allen bolt (supplied) through the original mount and the floorboard. It may also help to use the shank of a Phillips screwdriver in the bolthole at the same time to help align the holes. In some cases due to variances in the stock foot peg bracket it you may need to use a 25/64″ (.390) drill bit and drill thru both the bracket and the floorboards mounting block to allow the bolt to go thru. The blocks and their holes are machined to exact tolerances and is kept as close as possible to the size of the peg bracket so that there will not be any looseness or drooping of the floorboards when installed. Thread one of the Ny-loc nuts (supplied) onto the bolt and tighten securely. Reinstall shifter assembly and tighten securely. 3. Repeat for right side and re-check hardware for tightness. (The brake assembly will not need to be removed.)

2008 Triumph Rocket III specifications and pictures

0

Filed Under (Triumph) by admin on 06-11-2010

download
Triumph Rocket III 2008 Picture credits – Triumph . Click to submit more pictures. 2008 Triumph Rocket III More pictures… Discuss this bike Rate this motorbike This bike’s rating Write a review Sell this motorcycle Such bikes for sale Tip a friend List related bikes General information Model: Triumph Rocket III Year: 2008 Category: Custom / cruiser Rating: 68.5 out of 100. Show full rating and compare with other bikes Engine and transmission Displacement: 2294.00 ccm (139.98 cubic inches) Engine type: In-line three Stroke: 4 Power: 140.00 HP (102.2 kW)) @ 6000 RPM Torque: 147.00 Nm (15.0 kgf-m or 108.4 ft.lbs) @ 2500 RPM Compression: 8.7:1 Bore x stroke: 101.6 x 94.3 mm (4.0 x 3.7 inches) Fuel system: Injection. Multipoint sequential electronic fuel injection Fuel control: DOHC Ignition: Digital – inductive type – via electronic engine management system Cooling system: Liquid Gearbox: 5-speed Transmission type final drive: Shaft drive (cardan) Clutch: Wet. multi-plate Physical measures Dry weight: 319.3 kg (704.0 pounds) Seat height: 739 mm (29.1 inches) If adjustable, lowest setting. Overall height: 1,166 mm (45.9 inches) Overall length: 2,499 mm (98.4 inches) Overall width: 970 mm (38.2 inches) Wheelbase: 1,694 mm (66.7 inches) Chassis and dimensions Frame type: Tubular steel. twin spine Rake (fork angle): 32.0° Front suspension: 43mm upside down forks Rear suspension: Chromed spring twin shocks with adjustable preload Front tyre dimensions: 150/80-R17 Rear tyre dimensions: 240/50-R16 Front brakes: Double disc Front brakes diameter: 320 mm (12.6 inches) Rear brakes: Single disc Rear brakes diameter: 316 mm (12.4 inches) Speed and acceleration Fuel capacity: 23.84 litres (6.30 gallons) Color options: Claret. Phantom Black Further information Parts and accessories Check out parts and accessories from our partners. Ask questions Join the 08 Triumph Rocket III discussion group, the new Triumph forum at Bikez.name or the new Custom / cruiser forum at Bikez.name. Insurance, loans, testsSearch the web for dealers, loan and insurance costs, tests, customizing, etc. Related bikes List related bikes for comparison of specs

Incoming search terms:

Triumph Rocket III Installation Manual

0

Filed Under (Triumph) by admin on 29-10-2010

download
Control Switch Box 2) Linear Actuator 3) On-board Computer Module 4) Proximity Sensor 5) Leg Support Stand 6) Leg/Wheel System 7) Hardware Bag 8) Actuator Bracket If you believe you are missing any parts, please contact Chopper Design at 407-834-5007, and we will rectify the situation. If you haven’t already done so, install the uprights (purple above) to the plate. These uprights bolt to the plate on the top with (4) 3/8″ bolts and lock washers. Once this is done, use a helper and gently slide the plate (red above) under the bike. The green brackets above will line up with the empty holes in the frame we use to secure the front of the plate. The next step is to swing the back of the stand up and line up the two uprights with the holes that held the bolts you removed from the floorboard supports (notice the right support has a curved clearance cut in it to clear the support!). Use 2 longer bolts supplied to go through the tall uprights, into the holes and threads on the bike (use some blue thread locker on these). DO NOT TIGHTEN YET! Next find 2 bronze colored bolts, 4 washers and 2 nuts. Put a washer on the first bolt, and push this bolt through the hole in the frame in front of the saddlebag support bar, and through the short forward uprights on the plate. Put a washer and a nut on the end, and repeat the same on the other side. We want the uprights to be as perfectly vertical as they can be, so set the plate up this way and just snug these two bolts a bit. Now tighten all the fasteners a little at a time, while trying to keep these upright vertical. There are a total of 10 bolts to tighten/check: 8 • The (2) bolts holding the uprights • The (4) 3/8″ bolts holding the uprights to the support plate • The (2) bolts that attach the front uprights to the frame. See the pictures below for a better look as to what it all looks like once installed