Harley Davidson 2004-Up Sportster EZ-Steer Installation Manual

0

Filed Under (Harley Davidson) by admin on 16-02-2011

download
Installation Notes • Remove front fender, wheel, brake caliper, and fork tubes. • Remove all components attached to stock triple clamps, then the triple clamps themselves. • Remove upper and lower bearings including race. • Install new steering stem bearing races into neck. • Install new upper steering stem bearing with seal into neck. • Install Top and Bottom triple clamps into neck and snug steering stem bolt with washer. • Remove fork tube cap from both forks. • Install fork extensions with o-ring into fork tubes and tighten until fully seated. • Install fork tube caps with o-rings and tighten (see torque table). • Slide fork tubes into triple clamps until the top of each tube cap extends 0.42-0.50 in. above top surface of upper triple clamp. • Tighten 3/8-16 x 1.5″ bolts on upper triple clamp (see torque table). • Tighten steering stem bolt (see torque table). • Tighten pinch bolts on lower triple clamp (see torque table). • Install front wheel assembly and front brake caliper. • Install front fender. Item # Part Description Torque Spec (Lb. Ft.) – Fork Tube Cap 22-58 8 Bolt, Steering Stem, SP 30-35 11 3/8 – 16 X 1.5″ Socket Head Cap Screw 30-35 EZ-Steer Maintenance The bearings in your EZ-Steer rake kit are normal wear items, not subject to replacement under Champion’s one year Limited Warranty for the product. Failure to follow your motorcycle manufacturer’s recommendations for periodic OEM triple-tree maintenance will accelerate the wear on these bearings. Checking/adjustment of the steering stem nut torque with the front end lifted, in accordance with your motorcycle manufacturer’s recommendations, is important to reliable bearing service. Windshield Notes Please note that this EZ-Steer kit accommodates all known windshield types with the exception of a minor modification to Quick Release Compact Windshield, example part no. 58063-04. You will need to oblong the lower bolt holes as shown in figure

Honda GL1800 EZ-Steer Installation Manual

0

Filed Under (Honda) by admin on 16-02-2011

download
1. Use the Parts Checklist included with your hardware to verify the contents of the box. 2. Remove the front wheel, forks and triple clamps as shown in the Honda Shop Manual. 3. Remove the fork tube caps and install the new 1-inch extensions using the new “O” rings provided in your kit. 4. Install the new Triple Clamps. Remember to grease the new upper and lower steering bearings. The signal-cancel device under the lower triple clamp does not require special re-mounting hardware. 5. Install the forks into the new Triple Clamps. Check the steering lock action by turning the forks fully in both directions. 6. Reinstall the fender and wheel assembly. Be sure the brake hoses are routed to allow full travel of the forks.

HARLEY DAVIDSON CHROME FORK SLIDERS REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 10-02-2011

download
REMOVAL 1. Support the motorcycle so the front end is off the floor and the forks are fully extended. 2. Remove the front fender, front brake caliper(s) and front wheel according to instructions found in the Chassis section of the appropriate service manual. NOTE On some models other parts will also need to be removed to access the front forks. See the service manual. 3. For All Models EXCEPT Touring: Drain and remove the front forks. See the service manual. 4. For Touring models equipped with air-adjustable suspension: Bleed the air-adjustable suspension according to the instructions in the appropriate service manual. Wear safety glasses or goggles when servicing fork assembly. Do not remove slider tube caps without relieving spring preload or caps and springs can fly out, which could result in death or serious injury. (00297a) 5. For 2000 and Later Models EXCEPT Touring: See Figure 1. Using a piece of dental floss (or similar material) in a back and forth motion, loosen reflector from fork slider at both ends. Rotate reflector from side-to-side until it can be removed. Save reflector for future use. See Figure 2. Repeat procedure on the opposite side fork slider. Peel off any excess adhesive from both reflectors . Surface must be clean for installation. 6. Disassemble the front fork tubes according to instructions in the service manual. INSTALLATION NOTES The chrome fork sliders included in this kit install in the same manner as the original equipment parts. Refer to the service manual for proper installation procedures. Prior to installation of this kit, check the bores of the new chrome sliders to be certain they are free of dirt and debris or damage to the new sliders may occur. 1. Assemble the front fork tubes, replacing worn seals, bushings or other items as needed. NOTE Do not use an impact wrench to tighten the drain screws. Use of an impact wrench may damage the screws. 2. Tighten the drain screws: •Early Models with 39 mm forks (see Figure 2): Tighten to 13-17 in-lbs (1.5-1.9 Nm) •Early Models with 41 mm forks (see Figure 2): Tighten to 52-78 in-lbs (5.8-8.8 Nm) •Later Models (see Figure 3): Tighten to 52-78 in-lbs (5.8- 8.8 Nm) 3. Fill with TYPE E FORK OIL (99884-80) according to the instructions in the service manual. 4. Install the front fork and any parts that were removed to access the front forks. Install the front fender, wheel and caliper(s) according to instructions in the service manual. 5. For Touring models equipped with air-adjustable suspension: Refill the air-adjustable suspension system after assembly according to the service manual instruc- tions