2006 KTM 250 SX-F 250 EXC RACING 400 EXC RACING 450 SX, XC, EXC RACING 525 SX, XC, EXC RACING, REPAIR MANUAL

0

Filed Under (KTM) by admin on 05-05-2012

download
Hot start lever (250 SX-F) If you pull the red hot start lever [1] during the starting procedure backward, a bore in the carburetor will be opened through which the engine may take in additional air. The result is a „lean” fuel-air mixture of the type needed for hot starts.
ENGLISH 7 OPERATION INSTRUMENTS » Headlamp switch (EXCUSA) In this model the headlamp is switched on with the pull switch [1] . Flasher switch The flasher switch is a separate unit and is mounted on the left portion of the handlebar. The wire harness is designed in a way that whenever you want to use your bike off-road, you can dismount the entire turn indicator system without affecting the function of the remaining electrical system. Flasher left Flasher right Starter button (EXC) Pushing the black starter button [2] will actuate the E-starter. Emergency OFF switch (EXC Australia) The red emergency-OFF switch [3] is arranged adjacent to the throttle grip. In this position, the E-starter is operational and the engine can be started. In this position, the E-starter and ignition circuits are interrupted.The E-starter cannot be actuated, and the engine will not start, not even if you attempt to start it with the kickstarter. Pushing the black starter button [4] will actuate the E-starter. 2 3 4 5 6 Indicator lamps The green control lamp [5] flashes in the same rhythm as the flashing indicator when the indicator is working. The blue control lamp [6] lights up when the high beam is on

Incoming search terms:

2007 KTM 250 XC-F, XCF-W, EXC-F 400 XC-W, EXC RACING 450 XC, XC-W, EXC RACING 525 XC, XC-W, EXC RACING 525 XC DESERT RACING INSTALLATION MANUAL

0

Filed Under (KTM) by admin on 05-02-2012

download
Headlamp switch (XC-W) In this model the headlamp is switched on with the pull switch [1] . Flasher switch The flasher switch is a separate unit and is mounted on the left portion of the handlebar. The wire harness is designed in a way that whenever you want to use your bike off-road, you can dismount the entire turn indicator system without affecting the function of the remaining electrical system. Flasher left Flasher right Starter button Pushing the black starter button [2] will actuate the E-starter. Indicator lamps The green control lamp [5] flashes in the same rhythm as the flashing indicator when the indicator is working. The blue control lamp [6] lights up when the high beam is on. ENGLISH 7 2 Emergency OFF switch (EXC Australia) The red emergency-OFF switch [3] is arranged adjacent to the throttle grip. In this position, the E-starter is operational and the engine can be started. In this position, the E-starter and ignition circuits are interrupted.The E-starter cannot be actuated, and the engine will not start, not even if you attempt to start it with the kickstarter. Pushing the black starter button [4] will actuate the E-starter. 3 4 5 6 1 OPERATION INSTRUMENTS » ENGLISH 8 TEST All of the display segments briefly light up for the display function test. WS (wheel size) The display changes and the circumference of the front wheel is briefly displayed in millimeters (2205 mm corresponds to a front wheel circumference of 21″ with production tires). Afterwards the display will return to the previous display mode

Incoming search terms:

1988-2000 Honda Goldwing GL 1500 Signal Mirror Installation Instructions

0

Filed Under (Honda) by admin on 29-01-2011

download
Start on either the left or right side mirror. These instructions start with the right side mirror. Pull back the rubber boot covering the mirror mount. 1 2 3 Remove the accessory compartment cover. Remove the four screws on all sides of the accessory compartment. Remove the accessory compartment from the motorcycle fairing and set it aside. 4 The motorcycle’s electrical wiring for turn indicators is located forward of the accessory compartment cavity and behind the front amber turn indicator light. Disconnect the wire connected to the turn indicator light. 5 There are three screws holding the mirror housing to the mirror mount. Remove the three screws. Set the mirror housing aside.
Mirror Replacement – 2 – Remove the three screws holding the hinge to the mirror housing. Remove the hinge and remove the rubber boot surrounding the mirror housing. 1 Match the base of the hinge up to the new Signal® mirror housing. Mark the place on the hinge where the Signal® mirror wire will go through. Drill a ¼” hole in the hinge. 2 Position the rubber boot over the Signal® mirror housing. 3 Guide the Signal® mirror wire harness through the drilled hole in the hinge. Mount the hinge on the Signal® mirror housing using the original three screws.

Incoming search terms:

KTM 125 SX, EXC 200 EXC, XC, XC-W 250 SX, EXC, XC, XC-W 300 EXC, XC, XC-W OWNER'S MANUAL

0

Filed Under (KTM) by admin on 27-11-2010

download
Short circuit button (SX) The short circuit button [1] turns off the engine. When pressing this button, the ignition circuit is short-circuited. Combination switch (EXC) The light switch has 2, respectively 3 switch positions. [A] = Light off (this function is not available in all models) [B] = Low beam on [C] = High beam on You may use button [2] to actuate the horn. The red short circuit button [3] serves to switch off the engine. Leave the switch pressed until the engine stops. Headlamp switch (XC-W) In this model the headlamp is switched on with the pull switch [4] . Flasher switch The flasher switch is a separate unit and is mounted on the left portion of the handlebar. The wire harness is designed in a way that whenever you want to use your bike off-road, you can dismount the entire turn indicator system without affecting the function of the remaining electrical system. Flasher left Flasher right Emergency OFF switch (Australia) The emergency OFF switch [5] is located next to the throttle grip. Primarily designed as safety or emergency OFF switch, it should normally not be in its activated state. In this position, the ignition circuit is shorted; if the engine is running, it will stall immediately, if it is at standstill, it will not start. In this position, the ignition circuit is enabled; the engine should start. 1 2 3 5 A B C 4
ENGLISH 12 Filler cap To open it: turn filler cap counter-clockwise. To close it: put filler cap back on and tighten it by turning it clockwise. Install tank breather hose [1] without kinks. Filler cap (XC, XC-W) To open the filler cap: Turn the filler cap 45 ° counter-clockwise. To close the filler cap: Put the filler cap on and turn it 45 ° clockwise. Fuel tap OFF In this position the fuel tap is closed. No fuel can flow to the carbure- tor. ON During operation the twist grip must be turned to ON. This means that the fuel can flow to the carburetor. With the twist grip in this position the tank will be emptied until only the reserve is left. RES The reserve tank cannot be tapped until the rotating handle is turned to the RES position. Fill the tank as soon as possible and remember to turn the rotating handle back to the ON position so that you will have backup fuel next time, too. Reserve of the 8.5 l tank . . . . . . 1.3 l (0.32 USgallons) Reserve of the 10 l tank . . . . . .1.7 l (0.45 USgallons

YAMAHA XVS 650AK Supplementary Service Manual

0

Filed Under (Yamaha) by admin on 18-11-2010

download
Dimensions: Overall length Overall width Overall height Seat height Wheelbase Minimum ground clearance Minimum turning radius 2,450 mm (96.5 in) 930 mm (36.6 in) 1,105 mm (43.5 in) 710 mm (28.0 in) 1,625 mm (64.0 in) 145 mm (57.1 in) 3,400 mm (133.9 in) Basic weight: With oil and a full fuel tank 247 kg (544.5 lb) Bulb wattage quantity: Headlight Tail/brake light Front turn signal/position light Rear turn signal light Meter light Neutral indicator light High beam indicator light Turn indicator light Engine indicator light 12 V 60 W/55 W 1 12 V 8 W/27 W 1 12 V 27 W/8 W 2 12 V 27 W 2 12 V 1.7 W 1 12 V 1.7 W 1 12 V 1.7 W 1 12 V 1.7 W 1 12 V 1.7 W 1 ENGINE Item Standard Limit Connecting rod: Oil clearance Color code (corresponding size) 0.031 0.055 mm (0.0012 0.0022 in) Blue Black Brown Green CHASSIS Item Standard Limit Front suspension: Front fork travel Fork spring free length Installed length Spring rate (K1) Stroke (K1) Optional spring Oil capacity Oil level Oil grade 140 mm (5.5 in) 332.5 mm (3.1 in) 287.4 mm (11.3 in) 3.43 N/mm (0.343 kg/mm, 19.2 lb/in) 0 140 mm (0 5.5 in) No 0.507 L (17.4 US oz) 95 mm (3.74 in) Yamaha fork oil 10 WT or equivalent 325.9 mm (12.83 in) Front brake: Type Disc outside diameter thickness Pad thickness inner Pad thickness outer Master cylinder inside diameter Caliper cylinder inside diameter Caliper cylinder inside diameter Brake fluid type Single disk 298 5 mm (11.73 0.2 in) 6.0 mm (0.24 in) 6.0 mm (0.24 in) 14.0 mm (0.55 in) 30.2 mm (1.19 in) 33.3 mm (1.31 in) DOT 4 4.5 mm (0.18 in) 0.8 mm (0.03 in) 0.8 mm (0.03 in) Brake lever & brake pedal: Brake lever free play (at pivot) Brake lever free play (at lever end) Brake pedal position Brake pedal free play Clutch lever free play (at pivot) Clutch lever free play (at lever end) 1 2 mm (0.04 0.08 in) 10 15 mm (0.39 0.59 in) 108 mm (4.25 in) 20 30 mm (0.79 1.18 in) 2 3 mm (0.08 0.12 in) 10 15 mm (0.39 0.59 in)

Incoming search terms:

1999-2005 BMW K1200LT Motorcycle Signal Mirror Installation Instructions

0

Filed Under (BMW) by admin on 26-10-2010

download
1. Start on either the left or right side mirror. These instructions start with the right side mirror. Remove the factory mirror by inserting the pry bar as shown. Slowly twist the pry bar to disengage the mirror. NOTE: Insert the pry bar as close to the mirror mount as possible before prying out the OE mirror. Not doing so may cause the crossbar on the motor actuator to break. 2. Grab the mirror housing as shown and slowly push down to disengage housing from motorcycle. 3. Once you have the mirror housing removed, route the Signal® mirror wire harness through the hole in the housing. Note: Leave about 6″ of slack, on the wire, for adjustment later on. 4. Use a screwdriver and remove the screw from the front turn indicator lens. 5. Disengage the lens and remove the light bulb as shown. 6. Route the Signal® mirror wire harness through the top opening in (A) and out the bottom opening in (B).

2008 KTM 250 SX-F 250 XC-F, XCF-W 250 EXC-F, EXC-F SIX DAYS INSTALLATION MANUAL

0

Filed Under (KTM) by admin on 22-10-2010

download
Hand brake lever The hand brake lever [1] is mounted on the handlebars on the right and actuates the front wheel brake. The adjusting screw [A] can be used to change the basic position of the hand brake lever (see “Maintenance”). 1 A Short circuit button The short circuit button [2] turns off the engine. When pressing this button, the ignition circuit is short-circuited. 2 Headlamp switch (XCF-W) In this model the headlamp is switched on with the pull switch [5] . 5 Flasher switch The flasher switch is a separate unit and is mounted on the left portion of the handlebar. The wire harness is designed in a way that whenever you want to use your bike off-road, you can dismount the entire turn indicator system without affecting the function of the remaining electrical system. Flasher left Flasher right
OPERATION INSTRUMENTS » ENGLISH 7 1 2 3 4 5 Starter button Pushing the red starter button [1] will actuate the E-starter. Emergency OFF switch (EXC-F Australia) The red emergency-OFF switch [2] is arranged adjacent to the throttle grip. In this position, the E-starter is operational and the engine can be started. In this position, the E-starter and ignition circuits are interrupted.The E-starter cannot be actuated, and the engine will not start, not even if you attempt to start it with the kickstarter. Pushing the black starter button [3] will actuate the E-starter. Indicator lamps The green control lamp [4] flashes in the same rhythm as the flashing indicator when the indicator is working. The blue control lamp [5] lights up when the high beam is on. TEST All of the display segments briefly light up for the display function test. Electronic speedometer The display in the electronic speedometer is activated as soon as you press a button on the speedometer or an impulse is received from the wheel sensor. The display lights up when the engine is running. The display is cleared if no button is pressed for 1 minute or no impulse is received from the wheel sensor. The button is used to change between display modes. The + and – buttons are used to control various functions

Incoming search terms:

Incoming search terms: