Honda XR 400 Removal and Installation Manual

0

Filed Under (Honda) by admin on 09-12-2011

download
Turn Signal Switch Installation Front Wiring Connections Field Effect Transistor Installation Taillight Installation: Install the Acerbis DOT taillight over the empty well left in the stock fender using the two 5 x 20 mm bolts and 6 x 16 mm bolt found in the parts bag. Position the taillight over the previous taillight mounting well and transfer the hole locations for the top mounting holes onto the fender with a felt pen or snap punch (Photo 3) so that they are 3/8 of an inch above the edge of the taillight opening as shown in Photo 3. Drill two 3/16 inch holes for the top mounts. Attach the taillight using the top mounting screws, then pull the license plate holder down toward the bottom of the fender so that the taillight is pulled as horizontal as possible. Transfer drill a 1/4” hole at the bottom mounting location with the taillight in this position. When installing the bottom license plate mount bolt, make sure to install the 6 x 16 mm bolt from the bottom up to minimize the opportunity for the tire to grab it. Run the taillight
wires along the left frame rail using the stock wire clamps to support it. 8. Rear Turn Signal Installation: Turn signal mounting requires that you drill a 3/8 inch hole in either side of the rear fender near where it meets the side panels. You can achieve a clean,
durable installation using this mounting location. Mount the rear turn signals by drilling a 3/8 hole in the rear fender in the location shown in Photo 5, 3-3/4 inches back from the front edge (pointed tip of fender where it meets the side panel) and 2-3/4 “ up from the bottom edge Brake Light Switch Installation

Incoming search terms:

YAMAHA FZS6W OWNER’S MANUAL

0

Filed Under (Yamaha) by admin on 27-04-2011

download
Indicator and warning lights EAU11030 Turn signal indicator lights “ ” and “ ” The corresponding indicator light flashes when the turn signal switch is pushed to the left or right. EAU11060 Neutral indicator light This indicator light comes on when the transmission is in the neutral position. EAU11080 High beam indicator light This indicator light comes on when the high beam of the headlight is switched on. EAU11250 Oil level warning light This warning light comes on when the engine oil level is low. The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical circuit. NOTE: ● Even if the oil level is sufficient, the warning light may flicker when riding on a slope or during sudden acceleration or deceleration, but this is not a malfunction. ● This model is also equipped with a self-diagnosis device for the oil level detection circuit. If the oil level detection circuit is defective, the following cycle will be repeated until the malfunction is corrected: The oil level warning light will flash ten times, then go off for 2.5 seconds. If this occurs, have a Yamaha dealer check the vehicle. EAU11423 Coolant temperature warning light “ ” This warning light comes on when the engine overheats. When this occurs, stop the engine immediately and allow the engine to cool. The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical cir

Yamaha VMX12/ VMX12C Owner's Manual

0

Filed Under (Yamaha) by admin on 14-12-2010

download
Main switch EAUO0028 The main switch controls the ignition and lighting systems. The various main switch positions are described below. EAU00032 ON All electrical systems are supplied with power, the headlight, meter lighting, taillight and front position lights come on, and the engine can be started. The key cannot be removed. EAU00038 OFF All electrical systems are off. The key can be removed. 1. Push. 2. Release. 3. Turn P (Parking) The meter light, taillight and position lights are on, but all other electrical sys- tems are off. The key can be removed. The key must be pushed in from the “OFF” position to be turned to “P”. ECA00043 Do not use the parking position for an extended length of time, otherwise the battery may discharge. 1. Neutral indicator light ‘NEUTRAL’ 2. Turn signal indicator light ‘TURN’ 3. Fuel level warning light ‘FUEL’ 4. High beam indicator light ‘HIGH BEAM’ 5. Oil level warning light ‘OIL LEVEL’ EAU03034 Indicator and warning lights EAU00062 Neutral indicator light “NEUTRAL” This indicator light comes on when the transmission is in the neutral position. EAU00059 Turn signal indicator light “TURN” This indicator light flashes when the turn signal switch is pushed to the left or right. his warning light comes on when the fuel level drops below approximately 3 L (0.7 Imp gal, 0.8 US gal). When this occurs, refuel as soon as possible. The electrical circuit of the warning light can be checked according to the fol- lowing procedure. 1. Turn the key to “ON”. 2. If the warning light does not come on, have a Yamaha dealer check the electrical circuit. Oil level warning light “OIL LEVEL” This warning light comes on when the engine oil level is low. The electrical circuit of the warning light can be checked according to the following procedure. 1. Turn the key to “ON”. 2. If the warning light does not come on, have a Yamaha dealer check the electrical circuit. NOTE: EAU00064 High beam indicator light “HIGH BEAM” This indicator light comes on when the high beam of the headlight is switched on. Even if the oil level is sufficient, the warning light may flicker when riding on a slope or during sudden acceleration or deceleration, but this is not a mal- function

Incoming search terms:

YAMAHA FJR1300N OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 12-12-2010

download
3-2 3 EAU03034 Indicator and warning lights EAU04121 Turn signal indicator lights “” a n d “” The corresponding indicator light flashes when the turn signal switch is pushed to the left or right. EAU00061 Neutral indicator light ” ” This indicator light comes on when the transmission is in the neutral position. EAU00063 High beam indicator light ” ” This indicator light comes on when the high beam of the headlight is switched on. EAU03201 Oil level warning light ” ” This warning light comes on when the engine oil level is low. The electrical circuit of the warning light can be checked according to the fol- lowing procedure. 1. Set the engine stop switch to ” ” and turn the key to “ON”. 2. Shift the transmission into the neu- tral position or pull the clutch lever. 3. Push the start switch. If the warning light does not come on while push- ing the start switch, have a Yamaha dealer check the electrical circuit. NOTE: Even if the oil level is sufficient, the warning light may flicker when riding on a slope or during sudden acceleration or deceleration, but this is not a mal- function. EAU03192 Engine trouble warning light ” ” This warning light comes on or flashes when an electrical circuit monitoring the engine is defective. When this oc- curs, have the Yamaha dealer check the self-diagnosis system. The electrical circuit of the warning light can be checked according to the fol- lowing procedure. 1. Set the engine stop switch to ” “. 2. Turn the key to “ON”. If the warn- ing light does not come on, have a Yamaha dealer check the

Incoming search terms:

YAMAHA XT500E, XT600E SPECIFICATIONS AND OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 24-11-2010

download
INSTRUMENT AND CONTROL FUNCTIONS 3 ON OFF LOCK . EAU00040 LOCK The steering is locked, and all electrical systems are off. The key can be removed. To lock the steering 1. Turn the handlebars all the way to the left. 2. Push the key in from the “OFF” position, and then turn it to “LOCK” while still pushing it. 3. Remove the key. To unlock the steering Push the key in, and then turn it to “OFF” while still pushing it. 12 1. Push. 2. Turn.
3-2 INSTRUMENT AND CONTROL FUNCTIONS 3 EAU00056 Indicator lights EAU00063 High beam indicator light ” & ” This indicator light comes on when the high beam of the headlight is switched on. EAU00061 Neutral indicator light “N” This indicator light comes on when the transmission is in the neutral position. EAU00057 Turn signal indicator light ” 5 ” This indicator light flashes when the turn signal switch is pushed to the left or right. 12 3 1. High beam indicator light “&” 2. Neutral indicator light “N” 3. Turn signal indicator light “5 ” EAU00095 Speedometer unit The speedometer unit is equipped with a speedometer, an odometer and a tripmeter. The speedometer shows riding speed. The odometer shows the total distance traveled. The tripmeter shows the distance traveled since it was last set to zero with the reset knob. The tripmeter can be used to estimate the distance that can be traveled with a full tank of fuel. This information will enable you to plan future fuel stops

KYMCO MXU 500 SPECIFICATION AND OWNER'S MANUAL

0

Filed Under (Kymco) by admin on 12-11-2010

download
OFF ON (1) CONTROL FUNCTIONS 17 (1) Ignition switch (2) Key IGNITION SWITCH ON: Functions oft he respective switch positions areas follows: The key cannot be removed. Theenginecanbe started. OFF: “”: All electrical circuits are switched off except hazard light. The key can be removed in this position. All electrical circuits are switched on. The ignitions witch is ON while the position light and taillightwill light. All electrical circuits are switched on. Theenginecanbe started. The key cannot be removed. 18 INSTRUMENTS AND INDICATOR (1) Multi-function display (2) (3) (5) (6) Low-range indicator light”L” (7) High-range indicator light”H” (8) Neutral indicator light”N” (9) Reverse indicator light”N: (10) Park indicator light”P” (11) (12) Right turn signal indicator High beam indicator (4) Coolant temperature warning indicator Set button Mode button Left turn signal indicator (11) (2) (3) (4) (5) (8) (1) Multi-function display The display includes the following functions: Speedometer Odometer/Tripmeter Digital clock 2WD/4WDindicator Fuel gauge (2) Right turn signal indicator Flashes when the right turn signal operates. (3) High beam indicator The ignition switch is at the”"position, the high beam indicator will light when the headlight switch to select High beam () . Both left and right turn signal indicator will flash at the meantime when the hazard switch is operated and turn signal switch is turned off. NOTE: (12) (1) (7) (6) (9) (10) TRIP ODO mile kmPM 2WD 4WD SET MODE PRNHL
19 (4) Coolant temperature warning indicator When the coolant temperature reachesa specified level, this indicator comes onto warn that the coolant temperature is too hot. If the indicator comes on during operation, stopt he engine as soon as it is safe to do so and allow the engine to cooldown for about 10 minutes. (5) Set button This button is used to select ODO, TRIP A andT RIPB. This button is also used to adjust the time and reset the tripmeter. (6) Low-range indicator light”L” This indicator light comes on when the drive select lever is in the”L”position. (7) High-range indicator light”H” This indicator light comes on when the drive select lever is in the”H”position. (8) Neutral indicator light”N” This indicator light comes on when the drive select lever is in the”N”position

Incoming search terms:

KYMCO MXU 300/ 250 SPECIFICATION AND OWNER'S MANUAL

0

Filed Under (Kymco) by admin on 12-11-2010

download
FRAMES ERIAL NUMBER The frames erial number is stamped on the front oft he frame. (1) Frame serial number (2) Engine serial number 11 (1) (2) (01) Rear brake lever (03) Front brake lever (04) Right front turn signal light (02) Headlights/Position lights (05) Steering handlebar lock (06) Left front turn signal light 12 PARTS LOCATION (01) (02) (02) (03) (04) (05) (06) (07) Right rear turn signal light (08) Ta illights/Stoplights (11) Exhaust system (12) Trailer hitch (13) License light (14) Battery (09) Instrument and indicators (10) Left rear turn signal light (09) (08) (08) (10) (07) 13 (14) (13) (11) (12) 14 (15) Drive select lever Tool kit (19) Reservoir water tank (20) Brake pedal fluid reservoir (16) Fuel valve (17) Seat (18) (16) (15) (18) (17) (19) (20) 15 (21) ) Choke knob (23) Recoil starter Exhaust system (22 (23) (22) (21) (24) Front brake lever ) Front cargo rack (26) Front brake fluid reservoir (27) Ignition switch (28) Rear (29) Accessory socket seat (30) Rear brake lever (31) (32) Leftfootpeg /Parking brake (25 brake fluid reservoir Headlight dimmer switch Starter button Hazard switch Turn signal switch Horn switch (33) Fuel fill cap (34) Throttle lever (35) Rightfootpeg (36) Rear brake pedal 16 (33) (34) (32) (31) (35) (36) (24) (25) (26) (27) (28) (29) (30) NOTE: Themachineyou have purchased may differ slightly from those shown in the figures of this manual. (37) Rear cargo rack ) Flagpole bracket (38

Incoming search terms:

Yamaha YZF R1 SPECIFICATIONS AND OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 07-11-2010

download
INSTRUMENT AND CONTROL FUNCTIONS 3-1 3 EAU10460 Main switch/steering lock The main switch/steering lock controls the ignition and lighting systems, and is used to lock the steering. The various positions are described below. EAU10600 ON All electrical circuits are supplied with power, the meter lighting, taillight, license plate light, auxiliary lights and position lights come on, and the engine can be started. The key cannot be re- moved. NOTE: The headlights come on automatically when the engine is started and stay on until the key is turned to “OFF”, even if the engine stalls. EAU10660 OFF All electrical systems are off. The key can be removed. EAU10680 LOCK The steering is locked, and all electrical systems are off. The key can be re- moved. To lock the steering 1. Turn the handlebars all the way to the left. 2. Push the key in from the “OFF” position, and then turn it to “LOCK” while still pushing it. 3. Remove the key. 1. Push. 2. Turn. INSTRUMENT AND CONTROL FUNCTIONS 3-2 3 To unlock the steering Push the key in, and then turn it to “OFF” while still pushing it. WARNING EWA10060 Never turn the key to “OFF” or “LOCK” while the vehicle is moving, otherwise the electrical systems will be switched off, which may result in loss of control or an accident. Make sure that the vehicle is stopped before turning the key to “OFF” or “LOCK”. EAU11003 Indicator and warning lights EAU11030 Turn signal indicator lights “” and “” The corresponding indicator light flashes when the turn signal switch is pushed to the left or right. EAU11060 Neutral indicator light “” This indicator light comes on when the transmission is in the neutral position. EAU11080 High beam indicator light “” This indicator light comes on when the high beam of the headlight is switched on. EAU11250 Oil level warning light “” This warning light comes on when the engine oil level is low. The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical cir- cuit. NOTE: Even if the oil level is sufficient, the warning light may flicker when riding on a slope or during sudden acceleration or deceleration, but this is not a malfunction

Incoming search terms: