HONDA CBR 1000 RR AKRAPOVIC SLIP-ON & SLIP-ON STREET LEGAL EXHAUST SYSTEM REPAIR

0

Filed Under (Honda) by admin on 17-11-2011

download
INSTALLATION OF THE AKRAPOVIC SLIP-ON STREET LEGAL SYSTEMbinstalling the independent link pipe:m1. onto the stock collector properly install the metal ring for attaching the spring (Figure 27, 28) 2. install the metal clamp onto the Akrapovic independent link pipe (Figure 29) 3. slide the Akrapovic independent link pipe onto the stock collector; do not tighten the metal clamp (Figure 30) 4. attach the spring (Figure 31) 5. make sure the link pipe is not touching the frame and other parts installing the muffler: 1. correctly position the carbon-fiber clamp and slide it onto the muffler. WARNING: open the clamp to slightly wider than the diameter of the outer sleeve of the muffler – do not scrape it along the muffler outer sleeve! Do not fully tighten the bolts of the clamp (Figure 32) 2. position the muffler correctly and slide it onto the outlet side of the link pipe (Figure 33) 3. position and attach the springs (Figure 34) 4. tighten the carbon-fiber clamp onto the stock chassis hanging bracket on the frame (both sides of the motorcycle (Figure 35, 36, 37) 5. tighten the metal clamp at the independent link pipe – stock collector connection (Figure 38) 6. tighten the bolts of the carbon-fiber clamp. 7. reattach the stock heat shield (Figure 39, 40)8. reattach the rider’s footrest bracket (Figure 41) 9. make sure the muffler is not touching other parts of the motorcycle 10. reattach the license plate holder and turn signal lamps (Figure42, 43)11. reconnect the electrical leads for the rear light and reattach the fastback and both seats

2007 HONDA CBR600RR DUAL OUTLET SLIP-ON EXHAUST INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 07-11-2011

download
Make sure the motorcycle is cool and place securely on a service lift or stand. 2) Remove the two bolts securing the rider seat to the motorcycle. Remove the seat. See Figure #1 3) Using the key, remove the passenger seat. 4) Remove the bolts and push pin fasteners securing the tail section to the sub frame. Carefully spread the tail section and remove it from the motorcycle. See Figur ) Disconnect the turn signal & tail light plugs on the left side of the sub frame. 6) Remove the four bolts securing the complete rear fender assembly (including the tail light & turn signals) and the rear reflectors to the sub frame. Remove from the motorcycle. See Figure #2 7) Remove the two nuts from the back side of the reflectors and retain to be used elsewhere in Step #38. 8) Remove the two bolts securing the right side passenger peg. Remove the passenger peg. See Figure #4 9) Remove the bolt from the inside of the stock s-bend heat shield located behind the rear brake reservoir. See Figure #5 10)Remove the bolt securing the silver plastic heel cover from the right side rider peg mount. Remove the cover. See Figure #6 11)Remove the bolt securing the rear brake reservoir to the sub frame. Allow the reservoirto dangle

Yamaha TW200N/ TW200NC SPECIFICATIONS AND SUPPLEMENTARY SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 26-04-2011

download
GENERAL INFORMATION MOTORCYCLE IDENTIFICATION EAS00017 VEHICLE IDENTIFICATION NUMBER The vehicle identification number 1 is stamped into the right side of the steering head pipe. EAS00018 MODEL CODE The model code label 1 is affixed to the frame. This information will be needed to order spare parts CABLE ROUTING 1 Throttle cable 2 Front brake light switch lead 3 Right handlebar switch lead 4 Clutch cable 5 Left handlebar switch lead 6 Clutch switch lead 7 Front turn signal/position light lead (left) 8 Main switch lead 9 Indicator lights lead 0  Speedometer cable A Meter light lead B Headlight coupler C Wire harness D Front turn signal/position light lead (right) E Brake hose ب Fasten the brake hose with a plastic locking tie to the brake hose grommet. ة Fasten the wire harness with a plastic locking tie PERIODIC CHECKS AND ADJUSTMENTS INTRODUCTION This chapter includes all information necessary to perform recommended checks and abjustments.If followed, these preventive maintenance procedures will ensure more reliable vehicle operation, a longer service life and reduce the need for costly overhaul work.This information applies to vehicles already in service as well as to new vehicles that are being prepared for sale.All service technicians should be familiar with this entire chapter. PERIODIC MAINTENANCE CHART FOR EMISSION CONTROL SYSTEM

YAMAHA YZF-R6R/ YZF-R6SR/ YZF-R6RC/ YZF-R6SRC SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 26-04-2011

download
CABLE ROUTING SPEC A Pass the right handlebar switch lead inside the front brake hoses and over the throttle cables. B Install the throttle cables to the hook so that the pulling side of the throttle cables is routed downward. C Pass the clutch cable through the guide. D Plastic locking tie shall be positioned at 10 mm (0.39 in.) below from the upper bracket. E Clamp the left handlebar switch lead to the front fork with the plastic locking tie and cut the tip of the tie. Clamp it to the protector section Set in the coupler between the head light’s hollow section and the duct. J Install the relay to the rib of the head light. (Location for the left and right relays is alternative.) K To the wire harness L To the front turn signal light (right) M Set the sub wire harness in the joint. N Do not catch the sub wire harness when the duct is assembled. O To the front turn signal light (left) P Point the tip of the plastic locking tie to the front side of the vehicle. Cut the tip leaving 2 X 10 mm (0.08 X 0.39 in). Q Point the tip of the plastic locking tie under the under bracket and rear side of the vehicle. Cut the tip leaving 2 X 10 mm (0.08 X 0.39 in) A Pass the main switch lead under the left handlebar switch lead and then to the right side of the vehicle. B Pass the throttle stop cable by the left side of the side stand switch lead, oil level switch lead, A.C. magneto lead and then to the right side of the vehicle. C Pass the fuel tank drain hose and fuel tank breather hose inside of the reservoir tank breather hose, reservoir tank hose and wire harness and then route it by the out side of the starter motor lead. D Pass the coolant reservoir tank hose outside of the fuel tank drain hose and fuel tank breather hose. E Pass the fuel tank drain hose, fuel tank breather hose through the clamp of the coolant reservoir tank

Incoming search terms:

HARLEY DAVIDSON CUSTOM TOURING FRONT BULLET TURN SIGNAL KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-04-2011

download
INSTALLATION Outer Fairing/Windshield and Auxiliary Lamp Bracket Removal To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 2 3 1 2 is 01215 1. Six-position connector 2. Four-position connector 3. Auxiliary lamp connector Figure 1. Disconnect Signal and Auxiliary Lamp 1. Remove Maxi-Fuse. Refer to SYSTEM FUSES, MAXI- FUSE in Service Manual. NOTE Since the outer fairing screws hold the windshield in place, the windshield may fall to the floor if not removed. 2. Remove the windshield and outer fairing. Refer to UPPER FAIRING/WINDSHIELD in Service Manual for the outer fairing/windshield removal procedure. 3. Disconnect auxiliary lamp and turn signal connectors. NOTE See Figure 1. On 2005 and prior year models, the left and right turn signals plug into a 6-place connector located on the left fairing support brace. On 2006 and later models, each turn signal plugs into its own 4-place connector located toward the bottom of the inner fairing on each side. 4. Using a T40 Torx® drive head, remove and save the four bolts securing the auxiliary head lamp bracket to the chassis. 5. Remove auxiliary lamp bracket from motorcycle. Turn Signal Assembly 1 is 01217 1. Triangular opening Figure 2. Insertion of Terminals Through Triangular Opening 1. See Figure 2. Insert wire terminals through the triangular opening in the turn signal mounting bracket included in the kit. 2. Fit turn signal housing onto bracket. 3. Apply a small amount of Loctite (243) blue (99642-97) to threads of hex head cap screw. 4. Tighten cap screw to 15-20 ft-lbs (20-27 Nm) . -J03753 1 of 2 Turn Signal Installation 1 is 01218 1. Turn signal wire Figure 3. Turn Signal Wire Routing 1. See Figure 3. Insert turn signal connector and wiring between bottom of fairing and top of outer fairing skirt. 2. Route turn signal wire under cutout on mounting bracket and place bracket onto motorcycle. NOTE Care must be taken so the turn signal wire is not pinched between turn signal bracket and motorcycle chassis. 3. Install washers onto turn signal bracket mounting bolts and apply Loctite 243 (blue) (99642-97) to the bolt threads. 4. Tighten mounting bolts to 15-20 ft-lbs (20-27 Nm) . 5. Route turn signal leads toward harness connector. Secure loose wiring with tie straps so wires do not rub against any sharp objects

HARLEY DAVIDSON FLSTC SOFTAIL SADDLEBAG KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 16-04-2011

download
Additional Fitment Information Detachables NOTE If motorcycle has not been altered from fixed saddlebag hardware to accessory mounting detachable docking points. the separate purchase of Turn Signal Mounting Bar (Part Number 68611-98) is required for sufficient lock clearance. This kit is available at your Harley-Davidson Dealer. Installing these saddlebags on models equipped with a detachable sissy bar or detachable luggage rack requires the additional purchase of mounting hardware kit as follows: Hardware Kit Fitment 53075-03 2003 and later FLSTC models with detachables 53009-03 1987 through 2002 FLSTC models with detachables See Service Parts Page for kit contents. Additional weight can affect motorcycle stability, handling characteristics, and safe operating speed. Do not exceed 7 lbs. (3.18Kg) maximum load in each saddlebag. Evenly distribute weight between each saddlebag. Improper loading can cause vehicle handling problems leading to death or serious injury. Wide Tire If a wide tire kit has been installed, utilize the hardware and installation instructions found in that kit to reorient the fasteners to come from the inside to the outside of the finder. Button head screws from wide tire kit must be installed from the inside out, with the button heads on the inside of the fender. Failure to do so could result in bolt contacting tire, which could result in death or serious injury. Installation NOTE A Service Manual for your vehicle is available at your Harley-Davidson Dealer. 1. Remove seat. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative cable first) before proceeding. (00048a) Disconnect the negative (-) battery cable first. If positive (+) cable should contact ground with the negative (-) cable connected, the resulting sparks may cause a battery explosion which could result in death or serious injury. (00049a) 2. Disconnect battery cables, negative cable first. 3. Following instructions in applicable Service Manual, remove original saddlebags from supports. Install Turn Signal Mounting Bar If motorcycle is not equipped with accessory mounting detachable docking points, install Turn Signal Mounting Bar (Part No. 68611-98) following instructions provided with the kit. See Figure 1

Incoming search terms:

HARLEY DAVIDSON AUXILIARY BRAKE/RUN/TURN SIGNAL CONVERTER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-04-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Disconnect the battery cables, negative side first. 2. Remove the seat according to the procedures in the applicable Service Manual. NOTE Federal regulations require that red turn signal lenses need to be a minimum of 4 inches from the tail or stop lamp, edge to edge. In order to ensure this spacing requirement, new directional stand-offs are provided in kit and must be used to replace the original (stock) directional stand-offs. To install the new directional stand-offs, perform the following. 3. See Figure 1. Insert a small screwdriver into middle hole (1) of license plate light cover assembly (2). Push forward to release tail lamp spring clip. -J03679 1 of 4 2 1 is01493 1. Middle hole 2. License plate lamp assembly Figure 1. Removing Tail/Stop Lamp Assembly 4. See Figure 2. Lift tail lamp assembly upward and disconnect tail lamp connector (1). Disconnect left (2) and right (3) turn signal 2-place connectors. 5. See Figure 3. Remove two left side fender support front socket head screws (1). Save hardware for installation. 6. Remove left fender support capscrew (2) (under fender) near end of support and washer (3). Remove capscrew (4) at approximate midpoint of fender support and washer (5). Save hardware for installation. 7. Remove directional lamp screw (6) and washer (7). NOTE Prior to removing turn signal wires, carefully note routing. In particular, pay close attention to the locations of cable straps which must be replaced. 8. Carefully remove fender support (8), turn signal lamp (9) and directional lamp support (10) along with wiring through elongated hole in fender (11). Discard directional lamp support and cap screw. Save turn signal lamp for installa- tion. 9. Perform Steps 5 through 8 for the right fender support and signal lamp assembly. NOTE At this point, the two turn signal pin terminals must be removed from the two-place connector in order to remove the turn signal and directional stand-off from the fender support. The pin terminals will be re-installed to the connector after routing wiring through new directional stand-off and installing stand-off and turn signal to fender support. Follow the instructions under AMP MULTILOCK CONNECTORS in the applicable Service Manual to remove the pin terminals from the two-place con- nector. 10. See Figure 3. Obtain new directional stand-off and cap- screw from kit. Route wiring from turn signal lamp (9) through new directional lamp support (10) and elongated fender support hole (11). Install capscrew (6) through fender support, new directional lamp support then into turn signal. Tighten capscrew securely. 1 3 2 is 01494 1.4-place tail/stop lamp connector 2. Left turn signal 2-place multi-lock connector 3. Right turn signal 2-place multi-lock connector Figure 2. Disconnect Tail Lamp and turn Signal Connectors 11. Perform step 10 for the right side

HARLEY DAVIDSON FLSTC & FLSTS DOCKING HARDWARE WITH SADDLEBAG SUP- PORTS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 30-03-2011

download
The rear docking points in kit part number 90366-03 provide the rear mounting points for the Solo Rack. The rear mounting points from this kit ( 53931-03A ) will need to be installed to provide the clearance for the Solo Rack to be mounted. Table 2. Turn Signal Relocation Kit Requirement Turn Signal Relocation Kit Required Accessory Part Number 2003 and later FLSTC Not required 53815-00 Detachable Sideplates Not required 53066-00A Detachable Tour Pak Rack REMOVAL FLSTS Saddlebag Assembly Removal 1. See Figure 15. Remove a saddlebag by removing the acorn nut and washer on the lower support and the two flange locknuts inside the bag. Discard the flange locknuts but retain the acorn nut and washer. 2. See Figure 1. Remove the saddlebag support studs and their mounting hardware. 3. Repeat steps 1 – 2 on the other side of the vehicle. FLSTC Saddlebag and Fixed Mount Sissybar Removal 1. See Figure 15. Remove a saddlebag by removing the acorn nut and washer on the lower support and the two flange locknuts inside the bag. Discard the flange locknuts, but retain the acorn nut and washer. 2. See Figure 1. Remove the saddlebag support studs and their mounting hardware. 3. Remove and discard fixed mount sideplates. Retain sissy bar for use with detachable sideplates. 4. Repeat steps 1 – 3 on the other side of the vehicle. 1 is06914 1. Saddlebag support studs Figure 1. Original Equipment Hardware (FLSTS model shown) INSTALLATION Docking Hardware Installation – For Detachable Sideplates or Tour-Pak Rack NOTE See Figure 15. The rear docking point (8) is wider than the front docking point (2). -J02425 1 of 5 1. Place front docking point (2) on front stud (1), with countersunk end of docking point facing fender support. 2. Place spacer (6) for side plates or mid docking point (for detachable sideplate kit) on rear stud (1). 3. Place rear docking point (8) on bolt (7), with countersunk end facing fender support. 4. Insert front stud (1) through front docking point (2), fender support and into bracket underneath fender as shown. 5. Insert rear stud (1) through fender support and into bracket underneath fender as shown. 6. Install bolt (7) through fender support and into bracket underneath fender as shown. 7. Tighten front and rear studs (1) and bolt (7) to 27 ft-lbs (37 Nm) . 8. Repeat steps 1-7 on the other side of the vehicle.

Incoming search terms:

HARLEY DAVIDSON XR1200 LUGGAGE RACK KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 29-03-2011

download
Kit 53976-08 (XR1200 Passenger Upright Kit) is available for separate purchase. Contact your Harley-Davidson dealer for more information. Kit Contents See Figure 2 and Table 1. REMOVAL 1. Remove pillion and seat following the instructions in the appropriate Service Manual. 2. Remove the seat base following the instructions in the appropriate Service Manual. 3. See Figure 1. Remove the turn signal mounting screws (3) and discard. Allow the turn signal to hang by the harness until lower bracket installation. 4. Remove the rear fender support strut screws (6) and dis- card. INSTALLATION 1. See Figure 2. Install lower luggage rack mount bracket with screws (9), flat washers (10) and nuts (8). Bracket will mount around nut (Item 2 in Figure 1). Tighten to 19 ft-lbs (26 Nm) . 2. Install screws (7) and nuts (8) through the rear fender support strut and the lower luggage rack mount bracket. Tighten to 19 ft-lbs (26 Nm) . 3. Route the turn signal wire harnesses through the groove in the bracket. Install new turn signal mounting screws (11). Tighten screws to 3-5 ft-lbs (4-7 Nm) . 4. Install seat base following the instructions in the appropriate Service Manual. 5. Install upper luggage rack mount bracket (4) with original equipment seat base screws in the lower holes (A). Do not tighten at this time. 6. Install screws (3) into slotted holes in the upper luggage rack mount bracket (4) and flange nuts (6). Slide the upper bracket as far back in the slots as possible. Tighten screws (3) to 10 ft-lbs (13.5 Nm) 4 1 1 2 5 6 3 is05250 1. Lower luggage rack mount bracket screw (4) 2. Nut (2) 3. Turn signal mounting screw (4) 4. Upper luggage rack mount bracket 5. Luggage rack 6. Rear fender support strut screw (2) Figure 1. Luggage Rack Installation NOTE If installing the Passenger Upright Kit (part number 53976-08) (available separately), do not install spacers (2) and screws (3) in front holes. 7. Install luggage rack (1) aligning the holes with the holes in the upper luggage rack mount bracket. Install spacers (2) and screws (3) in holes. Tighten to 6-10 ft-lbs (8-13.5 Nm) . After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) 8. Install pillion and seat following the instructions in the appropriate Service Manual. Do not exceed luggage rack weight capacity. Too much weight can cause loss of control, which could result in death or serious injury. (00373a

Incoming search terms:

HARLEY DAVIDSON SPORTSTER CHOPPED FENDER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 28-03-2011

download
INSTALLATION Preparation 1. Position the vehicle on a motorcycle lift under the frame so the vehicle is upright and level. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 2. Refer to the service manual and follow the instructions given to remove the seat and disconnect the battery cables, negative (-) cable first. Retain all seat mounting hardware. 3. Remove the battery from the vehicle per the instructions in the service manual. 4. Raise the rear of the vehicle to relieve the load on the shock absorbers. 5. Follow the service manual instructions to remove only the bottom end shock absorber fasteners on each side of the vehicle. Save the fasteners for later assembly. 6. Raise the rear of the vehicle further to allow access to the underside of the rear fender. 7. Remove the license plate from the vehicle (if installed). Retain the plate and attaching hardware. Rear Fender Removal NOTE Note the location and orientation of rear fender mounting hardware, and save for later assembly. 1. Refer to the service manual and follow the instructions given to remove the rear fender, with the following exceptions: a. Removal of the tail lamp from the fender is not necessary. Rear Lamp Wiring 1. Cut off and discard the socket housings and terminal ends from the turn signal wires. 2. See Figure 1. Unscrew and remove the turn signal stalk (15) from one of the turn signal lamps, and discard. Remove and retain the turn signal lamp and support (14) from the rear fender support cover. 3. Insert the blade of a small screwdriver into the slot at the bottom of the turn signal lamp lens (2), and twist to unsnap the lens from the housing (1)