YAMAHA V-MAX PERIODIC MAINTENANCE AND MINOR REPAIR

0

Filed Under (Yamaha) by admin on 25-11-2010

download
PERIODIC MAINTENANCE AND MINOR REPAIR -. 1. Screw (x 2) EAU03003 Replacing the headlight bulb This motorcycle is equipped with a quartz bulb headlight. If the headlight bulb burns out, replace it as follows. 1. Remove the headlight unit by re- moving the screws. 2. Disconnect the headlight coupler, and then remove the headlight unit and bulb cover. 1. Headlight bulb holder 3. Remove the headlight bulb holder by turning it counterclockwise, and then remove the defective bulb. EWOOOl19 Headlight bulbs get very hot. Therefore, keep flammable products away from a lit headlight bulb, and do not touch the bulb until it has cooled down. 4. Place a new bulb into position, and then secure it with the bulb holder. 1. Do not touch this area. EC000105 Do not touch the glass part of the headlight bulb to keep it free from oil, otherwise the transparency of the glass, the luminosity of the bulb, and the bulb life will be adversely affected. Thoroughly clean off any dirt and fingerprints on the headlight bulb using a cloth moistened with alcohol or thinner. 5. Install the bulb cover, and then connect the coupler. 6. Install the headlight unit by install- ing the screws. 7. Have a Yamaha dealer adjust the headlight beam if necessary. 6-40 PERIODIC MAINTENANCE AND MINOR REPAIR 1. Screw (x 2) 1. Tail/brake light bulb (x 2) EAU00855 Replacing a turn signal light bulb or the tail/brake light bulb 3. Insert a new bulb into the socket, push it in, and then turn it clock- wise until it stops. 1. Remove the lens by removing the screws. 2. Remove the defective bulb by pushing it in and turning it counter- clockwise. 1. Turn signal light bulb 4. Install the lens by installing the screws. EC000108 Do not overtighten the screws, oth- erwise the lens may break

Incoming search terms:

YAMAHA V-STAR 650/ 1100 CLASSIC F ATS/ SLIMS MOUNTING KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Yamaha) by admin on 10-11-2010

download
1. Cover gas tank and front fender with towels to avoid damage during installation. 2. Install the two mounting plates onto the windshield, using the bottom and third bolt up. Leave the nylon washers off. The small tab goes to the bottom, big one at the top. (see Figure 1) Tabs face out away from the headlight when installed correctly. 3. Remove the headlight lens and chrome Turn Signal Bar cover and set them in a safe place. (see figure 2) 4. Remove the (3) socket head cap screws that hold the Headlight housing and let it rest carefully so that it does not fall. 5. Remove the turn signal bar by extracting the two socket head cap screws and let it dangle. (see figure 2) 6. Loosely install the throttle-side Bracket and Headlight using one of the (3) new longer 6mm x 30mm socket head cap screws. The nylon washer goes in between Headlight Housing and Headlight Bracket. (see figure 3) Install one of the (2) new 8mm x 45mm SS flat head screw and spacer in the lower hole to mount the turn signal bar. Insert the bolt in this order: bolt – windshield bracket – spacer – turn signal bar, and loosely tighten . (see Figure 3) Repeat these steps for the Clutch side. (See figure 4 for optional Cobra Light Bar installation, or to move Turn Signals forward to mount Lowers closer to the windshield.) 7. Once both windshield brackets are in place and all the new bolts are in place, Tighten all bolts. Re-install the chrome Turn Signal Bar cover. (Leave the chrome cover off if you use the alternate installation for Light Bar or Lowers). Re-Install the Headlight lens. 8. Loosen the (4) anchor bolts on the side of the windshield brackets. Slip the windshield mounting plates onto the brackets starting with the upper slot first then slip the bottom slot in. Adjust height, angle and tighten all bolts. This is a quick change kit. ALWAYS tighten all mounting bolts after removing or installing the windshield

Incoming search terms:

SUZUKI 1400/ 800 INTRUDER TURN SIGNAL RELOCATION INSTALLATION AND CLEANING INSTRUCTIONS

0

Filed Under (Suzuki) by admin on 09-11-2010

download
1. Refer to Figure 1. 2. Remove seat. Safety: disconnect battery prior to all wiring modifications LeatherLyke 510 5/1/2009 3. Disconnect wires to turn signals. 4. Remove turn signals and retain hardware for reinstallation. Observe and mark “left” and “right” for reinstallation. Information: Do not remove license plate bracket . 5. Remove license plate. Turn signal bracket must be oriented with flange (side with only 2 holes) on top. 6. Install turn signal bracket behind license plate bracket and license plate using 6 x 35mm pan phil machine screws for the 800 or 6 x 20mm pan phil machine screws for the 1400, 1/4″ flat washers, and 6mm locknuts. Insert black spacer spool between license plate bracket and turn signal bracket. 7. Mount turn signals directly to turn signal bracket using 6 x 10mm hex cap screws and star lock washer. Information: Observe all color-coding of wires and splice one wire at a time. 8. Cut each turn signal wires three inches from end and splice 10 inches of supplied wire. Secure wires to inner fender clips. 9. Follow route of tail light wires and connect wires into harness. 10. Secure wires together behind license plate bracket with tie wrap. 11. Connect battery and test turn signals for function. 12. Install seat. Information: Not all license plate mounts are grounded. In some cases, it may be necessary to run a ground wire to turn signal bracket. WARNING: States may have minimum width requirements on motorcycle turn- signals, so check your local laws. LeatherLyke 510 5/1/2009 SADDLEBAG INSTALLATION 13. Refer to Figure 2. Information: Cover plates are pressed into strut. 14. Remove round cover plate at end of fender mount strut on right side. 15. Remove nut on right rear and replace with 1.2″ hex adapter. If hex adapter is less than flush with the outside of both fender struts, add a 5/16″ flat washer. 16. Assemble 5 x 30mm flathead screw and 5mm mounting spool with chamfer on spool under head of screw. Insert assembly thru 1 1/4″ fender washer for the 1400 or 1″ for the 800. 17. Install spool assembly into previously installed 1.2” hex adapter. Information: Do not remove washer on shock absorber. Hex adapter will protrude 1/4″ beyond fender strut. 18. Remove round cover plate over right rear shock, remove shock absorber nut and install .75″ hex adapter. 19. Assemble 5 x 30mm flathead screw, mounting spool and cup washer with chamfer on spool under head of screw. 20. Install spool assembly into previously installed hex adapter. 21. Insert 5/8” finishing plug into old turn signal hole on right side. 22. Repeat procedures on opposite side

Incoming search terms:

Victory Vegas Rear LED Turn Signal Assembly Installation Manual

0

Filed Under (Victory) by admin on 31-10-2010

download
Step 1 •Prior to installation it is recommended that you perform a Pre-Function check. To do so, remove the left side battery cover from the bike and expose the post terminals. Hold the positive red lead from the turn signal to the positive red lead of the battery and then place the negative black lead from the turn signal to the negative black lead of the battery. Do one side at a time and ensure that both sides light prior to installation. Step 2 •Remove seat (passenger too if installed) •Remove fender “eyelashes” (required first if passenger seat is installed) •Remove the fender mounting bolts •Disconnect the rear turn signal and taillight harness connector located in the battery box compartment •Remove the fender by gentle prying outward and upward on one side to clear the mounting points, then the other side •Set aside on a flat and smooth surface to protect the fender’s finish (you may want to wrap it in a large towel) Step 3 •Turn the rear fender assembly upside down on a stable and covered/protected surface to prevent damaging the fender/paint •Remove the rear tail assembly and disconnect the wiring harness and license plate light. THIS PART IS NO LONGER NEEDED! Victory Vegas Rear LED Turn Signal Assembly Installation Guide •Remove the stock metal spacers shown below and replace them with the ¼” rubber spacers included in your accessory/installation kit. Step 4 •Place the turn signal assembly mounting arms over the rubber spacers. Align the turn signal in place so the space between the fender and the turn signal tube is consistent. After completing this step, place a small amount of Loc-Tite to the bolt and slowly tighten the stock nuts snugly in place, (extreme over-tightening may damage turn signal or fender lip). You should not need to loosen the mounting arms which are attached to the turn signal bracket to obtain the ideal fit; they are pre-assembled to be aligned. Please also note that due to manufacturing tolerances in the production of the fender, the rolled inner lip of it may interfere with the turn signal assembly seating properly. If this is the case, the lip can be tapped down flush with a rubber mallet or other appropriate tool. Take the necessary precautions to maintain your fender’s finish should this step be necessary. Step 5 •Run the wiring of the turn signal assembly in an appropriate/desireable path to the stock wiring harness. See picture below as an example. Once the wires are run, cut any excess wire and install the bullet connectors (included in the installation/accessory package) to the end of the wires. Due to the small gauge of the wire it’s suggested that you double it over before placing it into the bullet connector and solder it in place. Wire as follows:

Incoming search terms:

Victory Kingpin Rear LED Turn Signal Kit Installation Manual

0

Filed Under (Victory) by admin on 31-10-2010

download
Step 1 •Remove rider’s seat, strut covers, and passenger seat (if applicable) •Separate wiring harness connector for rear lights •Remove screws from each side of fender and plastic connectors from plastic inner fender •Carefully remove the fender by gentle prying outward and upward on one side to clear the mounting points, then the other side •Set aside on a flat and smooth surface to protect the fender’s finish Step 2 •Turn the rear fender assembly upside down on a stable and covered/protected surface to prevent damaging the fender/paint •Remove the metal piece that covers the rear wiring harness area (10mm socket) and unscrew the wire junction box (5mm Allen wrench) •Disconnect the turn signals from the stock wiring harness and unscrew the Allen bolts holding them in place (5mm Allen) •Enlarge the center mounting hole in the inner fender of the turn signal mounting location with a 3/8ths metal drill bit (see picture below). Victory Kingpin Rear LED Turn Signal Kit Installation Guide
Be extremely careful to drill slowly and make sure to avoid contact with the sides of the fender! Ensure that the surface area where the holes have been made are smooth. This will allow for a flush fit with the turn signal mounting blocks. If not, use a small file or other suitable tool to fix it. Don’t be concerned if your new hole extends into the other holes. Step 3 •Prior to installing the silver bullets, choose which style bezel you prefer, visor or visor-less. Both styles are included with amber LEDs only. Red LED silver bullets come standard with visor-less bezels, however visored bezels can be purchased separately. •Place the fender upright on a protected and secure surface. Insert the mounting blocks into place flush with the surface of the fender. They will only fit one way and are not interchangeable. Place a small amount of loc-tite on the threads of the hollow bolt. Hold the silver bullet LED light in place on the mounting block and thread the wire through the holes, and hand tighten the hollow bolt from the inside of the fender. Once a proper alignment of the lights has been achieved, tighten them securely with a 9/16ths box end wrench. Step 4 •Run the wiring of the turn signals in an appropriate/desireable path to the stock wiring harness. Once the wires are run, cut any excess wire and install the bullet connectors (included) to the end of the wires as noted in the wiring advisory and continue with wiring as follows: 1. Silver bullet right rear PURPLE to stock wire BLUE with RED stripe 2. Silver bullet right rear BLACK to stock wire BLACK 3. Silver bullet left rear PURPLE to stock wire BLUE 4. Silver bullet left rear BLACK to stock wire BLACK Make sure that the connectors are firmly snapped in place and are covered with the stock rubber connector. Ensure that the preexisting dielectric grease isn’t completely wiped off/removed, it will ensure conductivity and corrosion resistance. Please note that the amber LED silver bullets are dual intensity, while the stock system is single intensity (turn signal only). If you wish to wire your silver bullets to also function as running lights, the blue wire from each silver bullet must be wired to a “constant-on”/power wire, such as the stock purple wire that connects to the license plate assembly. If you do not wish to wire your turn signals for dual intensity then the blue wires should be tied off

Incoming search terms:

DUCATI PAUL SMART BERON TURN SIGNALS INSTALLATION MANUAL

0

Filed Under (Ducati) by admin on 26-10-2010

download
WHEN MOUNTING OBERON TURN SIGNALS TO THE FRONT FAIRING LOCATION YOU WILL NEED TO REMOVE THE CLIP # 13 AS SHOWN IN THE DRAW- ING. DISCONNECT PIGTAIL CONNECTORS FROM TURN SIGNAL AND THEN REMOVE NUT, LOCK WASHER AND ONE OF THE LARGE NYLON WASHERS. LEAVE THE OTHER LARGE NYLON WASHER IN PLACE. FEED THE WIRES AND INLINE CONNECTORS THROUGH THE HOLE IN THE FRONT COWLING AND THEN THREAD THE WIRES AND INLINE CONNECTORS FIRST THROUGH THE LARGE NYLON WASHER YOU REMOVED, THEN THE LOCK WASHER AND THEN THE NUT. SNUG UP THE NUT WITH THE SUPPLIED STUBBY WRENCH AND MAKE SURE THE TURN SIGNAL IS ALIGNED CORRECTLY. RECONNECT THE INLINE CONNECTORS TO THE PIGTAIL WITH THE OEM CONNECTOR. CONNECT THE OEM CONNECTOR TO THE MATING CONNECTOR ON THE WIRING HARNESS. NOTE THAT ON THE PAUL SMART THE WIRES MAY NEED REVERSING ON THE LEFT SIDE OF THE BIKE SINCE IT APPEARS DUCATI HAS MISWIRED THE HARNESS CONNECTOR. YOU WILL HAVE THIS SAME ISSUE IF MOUNTING IN THE “STOCK” LOCATION. REVERSING THESE WIRES IN JUST A MATTER OF DISCONNECTING THE INLINE CONNECTORS AND SWAPPING THEM

KAWASAKI Turn Signal Conversion Kit Installation Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Place motorcycle on solid, level ground and on center stand if equipped. 2. Remove your turn signal lens. Place it upside down and clean the lens interior with the supplied alcohol wipe. Allow to completely air dry. Note: the LEDs are mounted to the inside of the turn signal lens with the LEDs making direct contact with the lens. The supplied silicone is used to secure the LED board to the lens. It remains flexible but can be removed. Test fit the board in your lens prior to using silicone. 3. Using a small screwdriver, poke a small hole in the end of the tube of silicone. Place a dab of silicone on each of the 12 LEDs on the circuit board. CAUTION : Note the position of the metal pins on the back of the LED board, They must be located 90 degrees from where the holes are that secure the lens to the housing. See attached diagram. 4. Position the round circuit board over the inside of your turn signal lens with the LEDs facing down. Get the board as centered as possible. Allow the silicone to make contact with the inside of the lens and then push down and slightly rotate the board back and forth to allow the LEDs to make contact with the lens surface. Repeat other side. NOTE : the silicone will require 30 minutes in 70 degree weather to tack up. Full cure will occur within 24 hours. We suggest not riding for several hours if possible to allow the best adhesion. 5. You will need to access the following wires; running light (license plate can be used), brake lights, right turn and left turn. Disassemble the bike as needed to gain access to the wiring

Incoming search terms: