YAMAHA FZS6W OWNER’S MANUAL

0

Filed Under (Yamaha) by admin on 27-04-2011

download
Indicator and warning lights EAU11030 Turn signal indicator lights “ ” and “ ” The corresponding indicator light flashes when the turn signal switch is pushed to the left or right. EAU11060 Neutral indicator light This indicator light comes on when the transmission is in the neutral position. EAU11080 High beam indicator light This indicator light comes on when the high beam of the headlight is switched on. EAU11250 Oil level warning light This warning light comes on when the engine oil level is low. The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical circuit. NOTE: ● Even if the oil level is sufficient, the warning light may flicker when riding on a slope or during sudden acceleration or deceleration, but this is not a malfunction. ● This model is also equipped with a self-diagnosis device for the oil level detection circuit. If the oil level detection circuit is defective, the following cycle will be repeated until the malfunction is corrected: The oil level warning light will flash ten times, then go off for 2.5 seconds. If this occurs, have a Yamaha dealer check the vehicle. EAU11423 Coolant temperature warning light “ ” This warning light comes on when the engine overheats. When this occurs, stop the engine immediately and allow the engine to cool. The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical cir

YAMAHA XVS650/ XVS650A OWNER’S MANUAL

0

Filed Under (Yamaha) by admin on 27-04-2011

download
INSTRUMENT AND CONTROL FUNCTIONS Main switch/Steering lock The main switch controls the ignition and lighting systems. Its operation is described below. EAU00036 ON Electrical circuits are switched on. The engine can be started. The key cannot be removed in this position. EAU00038 OFF All electrical circuits are switched off. The key can be removed in this position. EAU00040 LOCK The steering is locked in this position and all electrical circuits are switched off. The key can be removed in this posi- tion. To lock the steering, turn the handlebars all the way to the left. While pushing the key into the main switch, turn it from “OFF” to “LOCK” and remove it. To release the lock, turn the key to “OFF” while pushing. EW000016 WARNING Never turn the key to “OFF” or “LOCK” when the motorcycle is moving. The electrical circuits will be switched off which may result in loss of control or an accident. Be sure the motorcycle is stopped before turning the key to “OFF” or “LOCK”. 1. Push 2. Turn EAU00044 (Parking) The steering is locked in this position and the taillight comes on, but all other circuits are off. The key can be removed in this position. To use the parking position, first lock the steering, then turn the key to “ ”. Do not use this position for an extended length of time as the battery may discharge

2002-2003 HONDA GL1800 BANK ANGLE SENSOR MOUNTING SCREWS REPAIR MANUAL

0

Filed Under (Honda) by admin on 22-04-2011

download
REPAIR PROCEDURE 1. Insert the ignition key into the lock cylinder and open the fairing pocket lid by turning the key clockwise. Remove the two trim clips by pushing the cen- ter pins in. Remove the two screws. Disconnect the opener  cable and remove the right fairing pocket. 2. To access the bank angle sensor, remove the two mounting screws  securing the connector holder. Place the holder to the side. 3. To check for the proper screw size, slightly tighten both bank angle sensor screws. If the screws are tight, reassemble the unit and apply the identification mark. If the screws spin in the holes, proceed to Step 4. 4. Using a magnetic screwdriver, remove and discard one of the two 4 mm screws securing the bank angle sensor assembly. Replace with a 5 x 12 mm self-tapping screw (see the PARTS INFORMATION section on page 3 for the proper screw for this repair). Repeat for the other screw. 5. Reinstall the removed parts in the reverse order of removal. IDENTIFICATION Apply a white paint dot in the center of the under- side of the right fairing pocket lid as shown. This will indicate that the Safety Recall has been per- formed on this unit

2002-2003 GL1800 BANK ANGLE SENSOR MOUNTING SCREW REPAIR PROCEDURE

0

Filed Under (Honda) by admin on 29-01-2011

download
1. Insert the ignition key into the lock cylinder and open the fairing pocket lid by turning the key clockwise. Remove the two trim clips by pushing the center pins in. Remove the two screws. Disconnect the opener cable and remove the right fairing pocket. 2. To access the bank angle sensor, remove the two mounting screws securing the connector holder. Place the holder to the side. 3. To check for the proper screw size, slightly tighten both bank angle sensor screws. If the screws are tight, reassemble the unit and apply the identification mark. If the screws spin in the holes, proceed to Step 4. 4. Using a magnetic screwdriver, remove and discard one of the two 4 mm screws securing the bank angle sensor assembly. Replace with a 5 x 12 mm self-tapping screw (see the PARTS INFORMATION section on page 3 for the proper screw for this repair). Repeat for the other screw. 5. Reinstall the removed parts in the reverse order of removal. IDENTIFICATION Apply a white paint dot in the center of the underside of the right fairing pocket lid as shown. This will indicate that the Safety Recall has been performed on this unit

YAMAHA YZF-R1R/ YZF-R1RC OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 03-12-2010

download
1. Right turn signal indicator light “” 2. Fuel level warning light “” 3. Oil level warning light “” 4. Neutral indicator light “” 5. Engine trouble warning light “” 6. High beam indicator light “” 7. Left turn signal indicator light “”
INSTRUMENT AND CONTROL FUNCTIONS 3-3 3 EAU04895 Oil level warning light “” This warning light comes on when the engine oil level is low. The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical cir- cuit. NOTE: Even if the oil level is sufficient, the warning light may flicker when riding on a slope or during sudden acceleration or deceleration, but this is not a malfunction. This model is also equipped with a self-diagnosis device for the oil level detection circuit. If the oil level detection circuit is defective, the following cycle will be repeated until the malfunction is corrected: The oil level warning light will flash ten times, then go off for 2.5seconds. If this occurs, have a Yamaha dealer check the motor- cycle. EAU00061 Neutral indicator light “” This indicator light comes on when the transmission is in the neutral position. EAU04896 Engine trouble warning light “” This warning light comes on or flashes when an electrical circuit monitoring the engine is defective. When this occurs, have a Yamaha dealer check the self-diagnosis system. (See page 3-7 for an explanation of the self-diagnosis device.) The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical circuit. EAU00063 High beam indicator light “” This indicator light comes on when the high beam of the headlight is switched on

Incoming search terms:

Yamaha YZF-R6 SPECIFICATION AND OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 19-11-2010

download
Shift timing indicator light This indicator light can be set to come on and go off at the desired engine speeds and is used to inform the rider when it is time to shift to the next higher gear. The electrical circuit of the indicator light can be checked by turning the key to “ON”. If the indicator light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical circuit. (See pages 3-7-3-10 for a detailed explanation of the function of this indicator light and on how to set it.) EAU04923* Coolant temperature warning light “” This warning light comes on when the engine overheats. When this occurs, stop the engine immediately and allow the engine to cool. The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical cir- cuit. Multi-function display The multi-function display is equipped with the following: a speedometer (which shows the riding speed) an odometer (which shows the total distance traveled) two tripmeters (which show the distance traveled since they were last set to zero) a fuel reserve tripmeter (which shows the distance traveled since the fuel level warning light came on) a clock a self-diagnosis device a display brightness and shift timing indicator light control mode NOTE: Be sure to turn the key to “ON” before using the “SELECT” and “RESET” buttons. To switch the speedometer and odometer/tripmeter displays between kilometers and miles, press the “SELECT” button and “RESET” button together for at least two seconds. Odometer and tripmeter modes Pushing the “SELECT” button switches the display between the odometer mode “ODO” and the tripmeter modes “TRIP 1″ and “TRIP 2″ in the following order: ODO → TRIP 1 → TRIP 2 → ODO If the fuel level warning light comes on (see page 3-2), the odometer display will automatically change to the fuel reserve tripmeter mode “F-TRIP” and start counting the distance traveled from that point. In that case, pushing the “SELECT” button switches the display between the various tripmeter and odometer modes in the following order: F-TRIP → TRIP 1 → TRIP 2 → ODO → F-TRIP

Yamaha XVS13AW SPECIFICATIONS AND OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 07-11-2010

download
INSTRUMENT AND CONTROL FUNCTIONS 3-1 3 EAU10460 Main switch/steering lock The main switch/steering lock controls the ignition and lighting systems, and is used to lock the steering. The various positions are described below. EAU10540 ON All electrical circuits are supplied with power, and the meter lighting, taillight, license plate light and position lights come on, and the engine can be started. The key cannot be removed. NOTE: The headlight comes on automatically when the engine is started and stays on until the key is turned to “OFF”, even if the engine stalls. EAU10660 OFF All electrical systems are off. The key can be removed. EAU10680 LOCK The steering is locked, and all electrical systems are off. The key can be re- moved. To lock the steering 1. Turn the handlebars all the way to the left. 2. Push the key in from the “OFF” position, and then turn it to “LOCK” while still pushing it. 3. Remove the key. To unlock the steering Push the key in, and then turn it to “OFF” while still pushing it. WARNING EWA10060 Never turn the key to “OFF” or “LOCK” while the vehicle is moving, otherwise the electrical systems will be switched off, which may result in loss of control or an accident. Make sure that the vehicle is stopped before turning the key to “OFF” or “LOCK”. 1. Push. 2. Turn. 1. Push. 2. Turn. INSTRUMENT AND CONTROL FUNCTIONS 3-2 3 EAU11003 Indicator and warning lights EAU11020 Turn signal indicator light “” This indicator light flashes when the turn signal switch is pushed to the left or right. EAU11060 Neutral indicator light “” This indicator light comes on when the transmission is in the neutral position. EAU11080 High beam indicator light “” This indicator light comes on when the high beam of the headlight is switched on. EAU11250 Oil level warning light “” This warning light comes on when the engine oil level is low. The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical cir- cuit. NOTE: Even if the oil level is sufficient, the warning light may flicker when riding on a slope or during sudden acceleration or deceleration, but this is not a malfunction. This model is also equipped with a self-diagnosis device for the oil level detection circuit. If the oil level detection circuit is defective, the following cycle will be repeated until the malfunction is corrected: The oil level warning light will flash ten times, then go off for 2.5 seconds. If this occurs, have a Yamaha dealer check the vehicle. EAU42740 Fuel level warning light “” This warning light comes on when the fuel level drops below approximately 3.7 L (0.98 US gal) (0.81 Imp.gal). When this occurs, refuel as soon as possible. The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, and then go off, have a Yamaha dealer check the electrical circuit. NOTE: The vehicle must be on a level surface and positioned upright, otherwise the fuel level warning light may not come on and go off at the appropriate times. This model is also equipped with a self-diagnosis device for the fuel level detection circuit. If the fue

Incoming search terms: