2001-2003 EFI Harley Davidson Softail Deuce Power Commander Installation Manual

0

Filed Under (Harley Davidson) by admin on 14-03-2012

download
1 Remove the seat. 2 Remove the two bolts that hold the relay bracket (Fig. A). Fig.A Remove these bolts 3 Fig.B 3 Pull straight upwards on the bracket. Lift the bracket enough to expose the 3 zip ties that hold the wiring harness to the bracket (Fig. B). Cut these 3 zip ties. 4 Pull upwards on the retaining plate (which holds the relays) enough to clear the battery (Fig. C). Fig.C Cut these 3 zip ties 4 9 Fig.D Adjusting Your Power Commander Your Power Commander has been programmed with a base map for your application. You can adjust the base map or install an alternate map using your Computer. Please refer to the supplied CD-Rom for more information. You can also adjust your Power Commander using the face plate buttons as described below. 1. With the ignition off, hold down all three buttons on the Power Commander III unit. 2. While still holding down the buttons, turn the ignition on. 3. Release buttons. 4. Select the range you wish to adjust: Low, Med, High, by pushing the corresponding button once. 5. At this point holding that button down will move the lights down ( leaning out the mixture). 6. Pushing the button repeatedly will move the light up (richening the mixture). 7. When the two center light are lit up this is the “0″ setting. After making your adjustments wait 20 seconds before starting the bike or turning it off. This allows the settings to be saved to memory. To verify that it is safe to start the bike, move the throttle and watch to see if the lights move up and down the scale. If they do, you may start or turn off the bike. Tabs 5 Rotate this plate forward to locate the relay retaining tabs (Fig. D). Bend these tabs so they are flush with the plate. This allows the relays to sit lower in the slots

Incoming search terms:

HARLEY DAVIDSON STAMPED MINI AND SHORT BACKREST KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-03-2011

download
These Stamped Backrest kits are designed for installation on all vehicles with Mini and Short sissy bar uprights. Kit Number 52527-01 is only for models equipped with a Mini sissy bar upright. Kit Number 52531-01 is only for models equipped with a Short sissy bar upright. See Service Parts illustration for kit contents. Installation 1. Remove stock chrome backrest bracket. Discard hardware. 2 Install backing plate (2) with 1/4 inch x .50 long screws (4) supplied with kit through mounting bracket and into backrest. Tighten screws to 7 ft-lbs (9.5 Nm). 3. Position stamped cover (1) so tabs and cover are slightly below notches in backing plate. Slide stamped cover (1) into position by sliding upwards until cover locks in position. 4. Install two #8 screws (3) through bottom of stamped cover (1) and then into backing plate (2). Tighten screws to 18-24 in-lbs (2.0 to 2.7 Nm)

Motorcycle Park sensor HRA – 7800 G2 User/ Installation Manual

0

Filed Under (Tips and Review) by admin on 27-11-2010

download
Drill the holes in the bumper as indicated in the installation diagrams below and install the sensors. Sensors 1, 4, 5 and 8 should NOT be mounted on the curve of the bumper. 2. Install the sensor vertically; the “up” arrow must be pointing upwards. 3. Connect the Red wire of the control unit to the (+) positive of ignition wire. 4. Connect the Black wire (-) to the vehicleʼs chassis. 5. Connect yellow wire to the (+) positive wire of the vehicle reverse indicating light. 6. Install the triggering micro switch on the panel, system will work when pressing the triggering switch. It is especially helpful when you want to park the car inside of the garage without engaging reverse gear. System will stay on for 2 minutes. 7. Clean the area of the dashboard where the LCD display is going to be mounted. 8. Remove the sticker off the bottom of display. Also remove protective screen cover from LCD screen. 9. Mount the display on the dashboard by firmly pressing down the display. 10. Connect the display unit, and then connect all sensors one by one 1. Installation of the screen The screen stick on the panel Which suitable for the driver 2. Installation of detectors 1. The sensors 5 and 8 must be installed at Same level. 2. The distance between The ground and the sensors is about 50-65 cm, suggested 55 cm. 3. The sensors must be installed perpendicular to bumper & avoid attaching on the metal. 4. To ensure the best detect position, the sensors 5 & 8 must be installed beside the edge 30-40cm, suggested 30cm. 5. After measurement, make a symbol. 6. To ensure best detecting results, the sensors 1 & 4 must be installed near the edge 8-13cm, suggested 11cm. 7. Measuring the distance between sensors 1 & 4 and marking a (L) sign. 8. Marking the points of sensors 2 & 3 by 1/3 L. 9. Using the 20mm drill, drill through the point which is marked, secure the sensors into the holes. 3. Installation of main unit 1. The main unit must be installed in the trunk to avoid moisture & heat. 2. Lead out the power wire from the startup facility of the vehicle, connect it to the power supply wire of the main unit. 3. Plug the power supply wire, screen wire & sensors wire respectively to the inputs of the main unit family.

Incoming search terms:

Incoming search terms: