Harley-Davidson Auxiliary LED Brake Light Installation Manual

0

Filed Under (Harley Davidson) by admin on 28-03-2012

download
If you are mounting the lighthead on a Harley-Davidson┬« motorcycle box, use the existing wire hole. Drill your mounting holes so the wire hole (located very close to the mounting hole in the lighthead) will line up with the wires, but not interfere with the mounting holes. Since the lighthead can mount to any vehicle, this manual will cover mounting to a generic location. 1. Mark the location of the 2 mounting holes onto the mounting surface using the dimensions shown above, or remove the lens and use it as a template. Always check behind the mounting surface to be sure you will not interfere with any other vehicle components. 2. Drill the 2 mounting holes using a drill sized for a #6 sheet metal screw, then drill the 9/32″ wire access hole 5/16″ away from the mounting hole as shown. 3. Feed the wires through the wire hole then secure the brake light to the mounting surface with the supplied mounting hardware. 4. Wire the lighthead into your existing brake light wiring, matching the lighthead wire colors to the vehicle wire colors (see “Wiring”). WARNING! All customer supplied wires that connect to the positive terminal of the battery must be sized to supply at least 125% of the maximum operating current and FUSED at the battery to carry that load. DO NOT USE CIRCUIT BREAKERS WITH THIS PRODUCT!

Harley Davidson Road King Lightbar installation manual

0

Filed Under (Harley Davidson) by admin on 06-03-2012

download
This product is designed to mount in the lowest, visible section of the motorcycle windshield. 1. Install the 3 housing edge seals (1 long seal and 2 short seals) onto the lightbar as shown (Fig. 1). Make sure that the seal is oriented so that the lip curls inward (Fig 2). 2. Remove the 3 screws shown from the upper section of the windscreen (Fig. 3.). CAUTION! DO NOT LOOK DIRECTLY AT THESE LED’SWHILE THEY ARE ON. MOMENTARY BLINDNESS AND/OR EYE DAMAGE COULD RESULT! IMPORTANT WARNING! WARNING! All customer supplied W ires that connect to the positive terminal of the battery must be sized to supply at least 125% of the maximum operating current and FUSED at the battery to carry that load. DO NOT USE CIRCUIT BREAKERS WITH THIS PRODUCT! Fig. 1 Fig. 4 Fig. 3 Fig. 2 3. Position the lightbar into its mounting position behind the windscreen. When properly positioned, the holes in the lightbar mounting tabs will be aligned with the vacant holes through the windscreen. 4. Using the mounting hardware included with the lightbar, secure the lightbar to the windscreen assembly. 5. Route the wires to their respective destinations (Fig. 4). It is left to the installation technician’s discretion to select a path for these wires that will both protect them from possible damage and not interfere with the operation of any other vehicle components or equipment

Incoming search terms:

HARLEY DAVIDSON ENGINE/ TRANSMISSION INTERFACE AND TOP COVER INSTALLATION INSRUCTIONS

0

Filed Under (Harley Davidson) by admin on 31-01-2011

download
INSTALLATION Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) 1. Refer to the Owner’s Manual and follow the instructions given to remove the maxi-fuse. 3 1 2 is02998 1. Transmission top cover screw (4) 2. Oil spout assembly screw 3. Upper bearing housing screw (2) Figure 1. Interface Cover Installation 2. See Figure 1. Remove and retain the four socket head cap screws (1) that fasten the front and right side of the transmission cover. See Figure 3. Obtain the chrome top interface cover (3) from the kit. NOTE The top interface cover can be carefully brought into position on top of the transmission housing from either the right or left side without removing or loosening any vehicle components. 3. Position the top interface cover over the transmission top cover. Loosely fasten the chrome cover to the top of the transmission housing with the screws removed in Step 2. 4. Obtain the chrome filler neck cover (4), 1/4-20 socket head screw (5), flat washer (6) and spacer (7) from the kit. Remove the oil level dipstick from the oil spout on the side of the transmission housing, wipe off and set it aside for later installation. NOTE Insert a clean shop rag into the oil spout opening while the dipstick is not installed. With the dipstick removed, small parts or other foreign material could fall into the transmission, leading to equipment damage or malfunction. 5. See Figure 1. Remove and discard the socket head cap screw (2) that fastens the oil spout assembly to the transmission housing. DO NOT remove the oil spout from the vehicle. 6. Place the flat washer over the threads of the new screw, and insert the screw into the unthreaded hole in the chrome filler neck cover. Place the spacer onto the screw threads. Apply a few drops of Loctite┬« 243 (Blue) to the screw threads, and position the chrome cover onto the oil spout on the transmission housing. Lubricate the filler neck gasket with soapy water to aid in installation. Tighten the screw to 84-132 in-lbs (9.5-15 Nm) . 7. See Figure 3. Obtain the chrome lower side interface cover (1), one #10-24 socket head screw (8) and one chrome flat washer (9) from the kit

Incoming search terms:

Harley-Davidson Electra Glide LED Motorcycle Lightbar Installation Guide

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
Mounting IMPORTANT! The lightbar should be located a minimum of 16″ from any radio antennas! This product is designed to mount in the lowest, visable section of the motorcycle windshield. The mounting procedure requires removal of the front facia panel of the motorcycle. 1. Remove the 3 screws along the base of the windshield from the upper section of the faring facia panel. 2. Remove the 4 remaining screws (shown above) that secure the facia panel to the faring. With these screws removed, the facia and windshield can now be removed from the motorcycle faring. 3. Position the lightbar into its mounting position. The base of the lightbar fits onto the three screw bosses used by the screws removed in step 1. 4. With the facia panel removed, the lightbar should now be wired. 5. Route the wires to their respective destinations. It is left to the installation technician’s discretion to select a path for these wires that will both protect them from possible damage and not interfere with the operation of any other vehicle components or equipment. 6. Using the original hardware removed in steps 1 & 2, remount the faring and windshield according to the motorcycle manufacturers service manual

HARLEY DAVIDSON ENGINE/ TRANSMISSION INTERFACE AND TOP COVER INSTALLATION

0

Filed Under (Harley Davidson) by admin on 25-12-2010

download
1. Refer to the Owner’s Manual and follow the instructions given to remove the maxi-fuse. 3 1 2 is02998 1. Transmission top cover screw (4) 2. Oil spout assembly screw 3. Upper bearing housing screw (2) Figure 1. Interface Cover Installation 2. See Figure 1. Remove and retain the four socket head cap screws (1) that fasten the front and right side of the transmission cover. See Figure 3. Obtain the chrome top interface cover (3) from the kit. NOTE The top interface cover can be carefully brought into position on top of the transmission housing from either the right or left side without removing or loosening any vehicle components. 3. Position the top interface cover over the transmission top cover. Loosely fasten the chrome cover to the top of the transmission housing with the screws removed in Step 2. 4. Obtain the chrome filler neck cover (4), 1/4-20 socket head screw (5), flat washer (6) and spacer (7) from the kit. Remove the oil level dipstick from the oil spout on the side of the transmission housing, wipe off and set it aside for later installation. NOTE Insert a clean shop rag into the oil spout opening while the dipstick is not installed. With the dipstick removed, small parts or other foreign material could fall into the transmission, leading to equipment damage or malfunction. 5. See Figure 1. Remove and discard the socket head cap screw (2) that fastens the oil spout assembly to the transmission housing. DO NOT remove the oil spout from the vehicle. 6. Place the flat washer over the threads of the new screw, and insert the screw into the unthreaded hole in the chrome filler neck cover. Place the spacer onto the screw threads. Apply a few drops of Loctite┬« 243 (Blue) to the screw threads, and position the chrome cover onto the oil spout on the transmission housing. Lubricate the filler neck gasket with soapy water to aid in installation. Tighten the screw to 84-132 in-lbs (9.5-15 Nm) . 7. See Figure 3. Obtain the chrome lower side interface cover (1), one #10-24 socket head screw (8) and one chrome flat washer (9) from the kit. NOTE For models with mid controls, the right-side rider footrest (foot peg) support bracket must be loosened to allow installation of the lower side interface cover. After the cover has been installed, tighten the footrest bracket attaching screws to 25- 35 ft-lbs (34-47 Nm) . 8. Position the cover around the chrome filler neck cover installed in Step 6. Loosely fasten the cover to the threaded hole in the filler neck cover with the screw and washer. 9. Obtain the chrome upper side interface cover (2), three #10-24 socket head screws (8) and three chrome flat washers (9) from the kit

Incoming search terms: