2001-2002 GL1800 A ABS Speed Sensor Wire Clamp Location INSPECTION/ REPAIR PROCEDURES

0

Filed Under (Honda) by admin on 29-01-2011

download
1. If the VIN is within the preceeding range, inspect the front ABS speed sensor wire clamp according to the following illustrations. 2001-2002 GL1800A ABS Speed Sensor Wire Clamp Location INCORRECT Installation CORRECT Installation Service Bulletin American Honda Motor Co., Inc. 2001-2002 GL1800 ABS Speed Sensor Wire Clamp Location 0112 GL1800 #9*GL1800 #9*0112*2001-2002 GL1800 ABS Speed Sensor Wire Clamp Location*GL1800, ABS Speed Sensor Wire Clamp Location*Motorcycle*1800 2 of 2 ©2001 American Honda Motor Co., Inc. – All Rights Reserved GL1800 #9 DECEMBER 2001 IDENTIFICATION There is no identification mark associated with this Service Bulletin. PARTS INFORMATION There is no parts information associated with this Service Bulletin. WARRANTY INFORMATION The normal warranty claim submission requirements apply. Submit one warranty claim per VIN with the following information only: Inspected and REPAIRED Template: GL#9 Hours: 0.2 hours Parts: None If the clamp is installed correctly on top of the speed sensor, no further action is necessary. 3. If the clamp is installed incorrectly under the speed sensor, remove and reinstall the clamp and speed sensor correctly. Torque the bolts,. Torque: 12 N • m (1.2 kgf • m, 9 lbf • ft) If the speed sensor wire clamp for the front ABS speed sensor is installed incorrectly, the ABS speed sensor air gap may be out of specification. This does not affect ABS speed sensor operation, but the clamp should be installed correctly. Inspect and repair all affected units using the Inspection/Repair procedures listed below. Inspect all unsold units and customer units brought in for service. AFFECTED UNITS 2001-2002 GL1800A units as follows: MODEL 2001 GL1800A All units 2002 GL1800A 1HFSC474*2A100001 – 1HFSC474*2A101643 * = denotes check digit Any unit in the above VIN range may be affected and should be inspected according to the procedures in this Service Bulletin. All units outside of the above VIN range do not require inspection. CUSTOMER NOTIFICATION There is no customer notification associated with this Service Bulletin.

Incoming search terms:

BMW Motorcycle R1100/ 850 Model Throttle Cables

0

Filed Under (BMW) by admin on 16-11-2010

download
Problem: Engine surges at constant speed. Difficult to adjust and balance the left and right throttle bodies. Cause: Differences in opening and closing of the throttle butterflies caused by friction in the throttle cable. Remedy: 1. Fit a low friction throttle cable. 2. Check the following to ensure optimum results: Ignition timing Spark plugs (FR 6DDC) type / condition (reference SI 2739 in Main Group 12) Valve clearances Correct Cat. code plug Check throttle housing inlet manifold for air leaks 3. Synchronize the throttle butterflies as illustrated on the attached procedure. Note: Make sure there are no obstructions in the vacuum stub pipe prior to connecting the Synchro tool. Parts: 32 73 1 342 149 R 1100 RS 32 73 1 342 150 R 1100 RT, R, & GS Information: The Low friction throttle cable was introduced into series production as follows: R 1100 RS from 0312537 onwards (06/95 prod.) R 1100 GS from 0381479 onwards (06/95 prod.) R 1100 R from 6379238 onwards (06/95 prod.) R1100RT from 0440499 onwards (06/95 prod.) R 850 from the start of production Warranty: The BMW Motorcycle Limited Warranty will cover the replacement of the throttle cable for motorcycles in the affected VIN range. Authorization is not Required . File a warranty claim, using the following information:

Incoming search terms: