HARLEY DAVIDSON REAR SADDLEBAG GUARDRAILS INSTALLATION MANUAL

0

Filed Under (Harley Davidson, Uncategorized) by admin on 18-04-2011

download
Installation KITNUMBER 49087-01 1. Remove and save fasteners that retain saddlebag guardrails. 2. Replace stock saddlebag guardrails with new guardrails from kit. 3. Screw in and torque each stock fastener as follows: a. Four stock screws, Part No. 3678, using two new locknuts (1), Part No. 7667. Torque each screw to 19 ft-lbs. b. Two stock screws, Part No. 3601 using two new locknuts (2), Part No.7686. Torque each screw to 9 ft-lbs. For Domestic FLHRC/I Vehicles Only. (Does not apply to Harley Davidson International (HDI) vehicles): Federal Motor Vehicle Safety Standard (FMVSS) 108 requires all motorcycles to be equipped with side reflectors. Install, or have Dealer install, the reflectors, Part Nos. 59370-98 and 59371-98, which are purchased separately. Loss of visibility to other motorists could result in death or serious injury. 1. See Service Parts illustration. Position reflector so it is centered on the vertical portion of the saddlebag guard 1″ above the top end of the lower bend where the radius turns upward. Measure and use a small piece of tape to mark location for attachment of the lower edge of the reflector at the 1″ mark. 2. Remove protective tape backing from one reflector. Locate reflector above the 1″ mark. Apply reflector, using even pressure by rubbing back and forth on reflector. Repeat for other side. Note Reflectors are specific for each side. Reflectors have a flat end and a curved end. The curved end goes down. Top edge should be horizontal when positioned on guard. If not, reflector is for opposite side. KITNUMBER 49088-01 1. Remove and save fasteners that retain saddlebag guardrails. 2. Replace stock saddlebag guardrails with new guardrails from kit. 3. Using four hexsocket button head screws (4) removed earlier, attach saddlebag guards using the remaining two existing holes in each guardrail. 4. Screw in and torque each stock fastener as follows: a. Four stock screws, Part No. 3678, using two new locknuts (1), Part No. 7667. Torque each screw to 19 ft-lbs. b. Two stock screws, Part No. 3601 using two new locknuts (2), Part No.7686. Torque each screw to 9 ft-lbs

HARLEY DAVIDSON SPLASH SHIELD KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-03-2011

download
This kit is designed to fit 1980 – 1983 and 1988 and later FLHT and 1994 and later FLHR models without fairing low- ers. installation 1. Locate splash shield for left side. Bar and Shield should face forward and opening in splash shield should be on right side. 2. Slip splash shield on left side of engine guard. 3. An opening in the outer edge of the splash shield allows the splash shield to fit over highway footrests. 4. Place the wide attaching strap around the frame down- tube, do not put strap over clutch cable. 5. Slip buckles on attaching strap onto mating buckle halves attached to back side of splash shield. Latches will snap into locked position when buckle is properly closed. 6. Adjust the fit by lifting the Velcro┬«attached straps (on rear of splash shield) and changing length as required. 7. Repeat procedure for right side of vehicle. NOTE If splash shields cover amber reflectors mounted on frame down tubes, install reflectors included in kit as follows: 8. See Figure 1. Clean areas on both sides of fender (1) where amber reflectors are to be mounted. 9. Remove backing paper from rear of reflector and place reflectors in position (2). Federal Motor Vehicle Safety Standard (FMVSS) 108 requires motorcycles to be equipped with rear and side reflectors. Be sure rear and side reflectors are properly mounted. Low visibility of rider can result in death or serious injury. (00336a) NOTE To remove splash shields depress both latches with thumb and forefinger and gently pull buckle apart. Open remaining buckle and slide splash shield off engine guard

Kinroad XT250GK (double-seat): Owner's Manual

0

Filed Under (Kinroad) by admin on 30-11-2010

download
Keep Hands and Feet on Controls Always keep both hands on the steering wheel and both feet on the foot controls when driving your BUGGY. It is important to maintain your balance and to control the BUGGY. Removing hands or foot away from the controls can reduce your ability to react control of the BUGGY. 250GK (double-seat): Ownr`s Manual 20 Control Speed Driving at excessive speed increases the chances of an accident. In choosing a proper speed, you need to consider the capability of your BUGGY, the terrain, visibility and other operating conditions, plus your own skills and experience. . Use Care on Unfamiliar or Rough Terrain Before driving in a new area, always check the terrain thoroughly. Don’t drive fast on unfamiliar terrain or when the visibility is limited. (It’s sometimes difficult to see obstructions like hidden rocks, bumps, or 250GK (double-seat): Ownr`s Manual 21 holes in time to react.) Never drive past the limit of visibility. Maintain a safe distance between your BUGGY and other off-road vehicles. Always exercise caution and use extra care on rough, slippery and loose terrain. 250GK (double-seat): Ownr`s Manual 22 Do Not Perform Stunts You should always operate your BUGGY in a safe and reasonable manner. When driving, always keep all four wheels on the ground.

Incoming search terms: