SUZUKI PKT-045 V-STROM LEFT FRONT PANEL Installation Manual

0

Filed Under (Suzuki) by admin on 19-02-2012

download
STEP #1 – Remove the seat & the left side fairings. See the Suzuki service manual. STEP #2 – Drill a 18mm hole into the panel (11/16″ hole saw recommended and is available on our site) where shown [A]. If the hole is too small for the socket open it with emery cloth or a file. Watch the clearance behind the panel; make sure the socket has room. Attach the socket to the panel; use a dab of Silicone on the socket and jam nut. Important: Do NOT use Loctite or over-tighten. STEP #3 – Install the cable starting at the battery through to the front of the bike. Route the cable under the bracket [B]. You’ll find it a bit tight to get through between the frame and motor [C]. Ty-wrap the cable to the frame. Run the cable up to the front fairing. Slip the fuse-holder in the location shown [D]. Disconnect the black and red battery terminals. Connect the ground wire to the bolt [E]. You can cut a notch in the ref boot [F]. Connect the red wire to the battery posts as follows: RED WIRE = BATTERY POSITIVE STEP #4 – Reconnect the positive & negative battery terminals. Install the fuse in the fuse-holder. The center terminal is plus and the outer ring is negative (see dwg below). Apply either dielectric grease or Vaseline to terminals. Connect the red wire to the POSITIVE terminal and the black wire to the NEGATIVE terminal. Use a voltmeter to check if the polarity is correct. STEP #5 – Apply the remaining ty-wrap to the wiring harness where needed. Do NOT allow the harness to directly contact the motor or exhaust.

SUZUKI SV650 REAR SET POWERLET Installation Manual

0

Filed Under (Suzuki) by admin on 15-02-2012

download
STEP #1 – Remove the seat. See the Suzuki service manual. STEP #2 – Stretch out the wiring harness. Run the harness down the LEFT side of the battery cover, between the frame and the plastic water protectors/inner fender. There is a hole through which the harness may pass, visible when looking down to the left side of the battery cover, and toward the rear [B]. Insert a tie wrap, upward, though the black ring behind the silver footpeg bracket [A]. Let the wire hang down by the rearset for now. Next remove the negative battery connection, followed by the positive battery connection. Route the red lead forward toward the battery through the “notch” on the left side of the battery cover. Connect the red & black wire as follows: RED WIRE = BATTERY POSITIVE BLACK WIRE = CHASSIS GROUND Chassis bolt [D]. Tuck the fuse holder into a cavity in front of the plus terminal of the battery [C] under the battery cover. Ty-wrap the fuse-holder to the nearby wiring. STEP #3 – Apply either dielectric grease or Vaseline to the terminals. The center terminal is plus and the outer ring is negative (see dwg below). Install the fuse in the fuse holder. Connect the red wire to the positive terminal & the black wire to the negative terminal. Use a voltmeter to check if the polarity is correc

HARLEY DAVIDSON CHROME INSTRUMENT BEZEL COVER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-03-2011

download
This kit is designed for installation on voltmeter, fuel gauge, oil pressure and air temperature gauges used on 1986 and later FLT and FLHT models. Kit Contents Table 1. Kit Contents Description Quantity Chrome bezel cover 2 Adhesive tape, double-sided strip 1 There are no Service Parts available with this kit. INSTALLATION NOTE Using a 50:50 mixture of isopropyl alcohol and water, wipe dirt, oil and grease off of instrument bezel and bezel cover before applying double-sided tape or tape may not adhere well. 1. See Figure 1. Cut tape (1) into six equal pieces. 2. Remove paper liner from one side of tape and apply tape to front face of gauge pressing firmly into place. Space all three pieces equally. 3. Remove outer liner from tape. 4. Place bezel over gauge and press firmly into place

HARLEY-DAVIDSON 12 VOLT BATTERIES CARE AND MAINTENANCE

0

Filed Under (Harley Davidson) by admin on 30-01-2011

download
CARE AND MAINTENANCE Voltmeter Test See Table 2. The voltmeter test provides a general indicator of battery condition. Check the voltage of the battery to verify that it is in a 100% fully-charged condition. If the open circuit (disconnected) voltage reading is below 12.7 V, charge the battery and then check the voltage again after the battery has set for one to two hours. If the voltage reading is 12.7 V or above, perform a load test. Table 2. Voltmeter Test For Battery Charge Conditions STATE OF CHARGE VOLTAGE (OCV) 100% 12.7 V 75% 12.6 V 50% 12.3 V 25% 12.0 V 0% 11.8 V Disconnection and Removal Refer to a service manual for specific disconnection and removal steps. Pay attention to all warnings and cautions within the manual and remove battery from battery box/tray. Battery Charging Batteries contain sulfuric acid, which could cause severe burns to eyes and skin. Wear a protective face shield, rubberized gloves and protective clothing when working with batteries. KEEP BATTERIES AWAY FROM CHILDREN. (00063a) 1. Never charge a battery without first reviewing the instructions for the charger being used. 2. Perform a voltmeter test to determine the state of charge. See BATTERY TESTING, VOLTMETER TEST. If battery needs to be charged, proceed to Step 3. Remove battery from motorcycle before charging. Electrolyte leakage will damage motorcycle parts. (00213a) Explosive hydrogen gas, which escapes during charging, could cause death or serious injury. Charge battery in a well-ventilated area. Keep open flames, electrical sparks and smoking materials away from battery at all times. KEEP BATTERIES AWAY FROM CHILDREN. (00065a) 3. See applicable service manual and remove the battery from the motorcycle. Place the battery on a level surface. 4. Inspect battery for damage. Replace battery if visibly damaged or frozen. 5. Inspect battery charger, verify that the charger leads are not damaged, frayed or loose

Incoming search terms: