YAMAHA RX10H/ RX10SH RX10MH/ RX10MSH/ RX10RH/ RX10RSH SERVICE AND OWNER’S MANUAL

0

Filed Under (Yamaha) by admin on 27-04-2011

download
Throttle override system (T.O.R.S.) If the carburetor or throttle cable should malfunction during operation, the T.O.R.S. will operate when the throttle lever is released. The T.O.R.S. is designed to interrupt the ignition and keep the engine revolution speed between 2,800 and 3,000 r/min if the carburetor fails to return to idle when the lever is released. Speedometer unit The speedometer unit is equipped with the following: a digital speedometer (which shows riding speed) an odometer (which shows the total distance traveled) a tripmeter (which shows the distance traveled since it was last set to zero) warning indicators (which show self-diagnosis, cool ant temperature, fuel level, and oil level warnings) fuel meter (which shows the fuel remaining in the fuel tank) grip/thumb warmer heat level indicator  (which shows the heat level of the grip warmer or the thumb warmer) After the engine is started, the tachometer 1 makes one sweep, and the warning light 2 and all segments of the meter 3 turn on and off once. Then the warning light turns on again, and then goes off if there are no problems. The grip warmer heat level is initially displayed for 5 seconds, then switches to the fuel meter display. Odometer and tripmeter modes Pushing the select/reset button 4 switches the display between the odometer mode “ODO” and the tripmeter mode “TRIP”. To reset the tripmeter, push the select/reset button for at least one second while the tripmeter is displayed. NOTE: @ To switch the speedometer, odometer, and tripmeter displays between kilometers and miles, select the odometer mode “ODO”, and then push the select/reset button 4 for at least 10 seconds. ESU00363 High beam indicator light The high beam indicator light 1  comes on when the high beams of the headlights are switched on. (See page 5-12 for headlight beam switch operation.)

YAMAHA FZS6W OWNER’S MANUAL

0

Filed Under (Yamaha) by admin on 27-04-2011

download
Indicator and warning lights EAU11030 Turn signal indicator lights “ ” and “ ” The corresponding indicator light flashes when the turn signal switch is pushed to the left or right. EAU11060 Neutral indicator light This indicator light comes on when the transmission is in the neutral position. EAU11080 High beam indicator light This indicator light comes on when the high beam of the headlight is switched on. EAU11250 Oil level warning light This warning light comes on when the engine oil level is low. The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical circuit. NOTE: ● Even if the oil level is sufficient, the warning light may flicker when riding on a slope or during sudden acceleration or deceleration, but this is not a malfunction. ● This model is also equipped with a self-diagnosis device for the oil level detection circuit. If the oil level detection circuit is defective, the following cycle will be repeated until the malfunction is corrected: The oil level warning light will flash ten times, then go off for 2.5 seconds. If this occurs, have a Yamaha dealer check the vehicle. EAU11423 Coolant temperature warning light “ ” This warning light comes on when the engine overheats. When this occurs, stop the engine immediately and allow the engine to cool. The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical cir

2006 HONDA GOLD WING Specifications

0

Filed Under (Honda) by admin on 29-01-2011

download
Engine Type Liquid-cooled 4-stroke 12-valve SOHC flat-6 Displacement 1,832cm3 Bore x Stroke 74 x 71mm Compression Ratio 9.8 : 1 Max. Power Output 87kW/5,500min-1 (95/1/EC) Max. Torque 167Nm/4,000min-1 (95/1/EC) Idling Speed 700min-1 Oil Capacity 4.6 litres Fuel System Carburation PGM-FI electronic fuel injection with automatic choke Throttle Bore 40mm Aircleaner Viscous, cartridge-type paper filter Fuel Tank Capacity 25 litres (including 4-litre warning light reserve) Electrical System Ignition System Computer-controlled digital transistorised with electronic advance Ignition Timing 2° BTDC (idle) ~ 30° BTDC (3,500min-1) Sparkplug Type BKR6E011 (NGK); K20PR-U11 (ND) Starter Electric Battery Capacity 12V/18AH ACG Output 1,000W Headlights 12V, 55W x 2 (low) / 55W x 2 (high) Drivetrain Clutch Wet, multiplate with coil springs Clutch Operation Hydraulic Transmission Type 5-speed (including overdrive, plus electric reverse) Primary Reduction 1.591 (78/49) Gear Ratios 1 2.375 (38/16) 2 1.454 (32/22) 3 1.068 (31/29) 4 0.843 (27/32) 5 0.686 (24/35) Final Reduction 2.750 (33/12) Final Drive Enclosed shaf

Incoming search terms:

DUCATI SUPERBIKE 848 Owner's manual and maintenance manual

0

Filed Under (Ducati) by admin on 14-12-2010

download
Position of the motorcycle controls (fig. 3) 1) Instrument panel. 2) Key-operated ignition switch and steering lock. 3) Left-hand handlebar switch. 4) Clutch lever. 5) Rear brake pedal. 6) Right-hand handlebar switch. 7) Throttle twistgrip. 8) Front brake lever. 9) Gearchange pedal. 1 4 3 2 9 8 5 7 6 fig. 3 11 E Instrument panel (fig. 4) 1) LCD (see page13). 2) Tachometer (rpm). Indicates engine revs per minute. 3) Neutral (N) indicator ( green ). Illuminates when the gearbox is in neutral. 4) Fuel warning light ( yellow ). Illuminates when there are about 3 litres of fuel left in the tank. 5) Turn signal indicator light ( green ). Illuminates and flashes when the turn signal is in operation. 6) Engine oil pressure warning light ( red ). Illuminates when engine oil pressure is too low. This light should illuminate when the ignition is switched to ON and should go out a few seconds after the engine starts. It may come on briefly if the engine is very hot, but should goout again as engine speed increases. Important If this light (6) stays on, stop the engine to avoid serious damage. 7) High beam warning light ( blue ). Illuminates when the high beam headlight is on. 8) “Engine diagnostics light” ( amber ). The engine ECU illuminates this light steadily to indicate the presence of errors leading to engine lock. 9) “Motorcycle diagnostics” light . Illuminates when the motorcycle diagnostics detects a problem. 10) Rev limiter indicator lights . Indicator light 10A: illuminates steadily at 800rpm before intervention of the rev limiter. Indicator lights 10A + 10B: illuminate steadily 400rpm before intervention of the rev limiter. Indicator lights 10A + 10B + 10C: start flashing when the rev limiter is reached. 2 1 5 9 8 6 3 4 5 7 10B 10C 10A fig. 4 12 E 11) 2-position switch A and B . Switch used for displaying and setting instrument panel parameters. It has two positions, A “▲” and B “▼”. 12) High beam headlight flasher switch (fig. 5). The high beam headlight flasher switch is also used for theLAP and USB data aquisition functions.

DUCATI MONSTER 696 Owner's manual and maintenance manual

0

Filed Under (Ducati) by admin on 14-12-2010

download
instrument panel (fig. 4) 1) LCD (see page13). 2) Tachometer (rpm). Indicates engine revs per minute. 3) Neutral (N) indicator ( green ). Illuminates when the gearbox is in neutral. 4) Fuel warning light ( yellow ). Illuminates when there are approximately 3litres of fuel left in the tank. 5) Turn signal indicator light ( green ). Illuminates and flashes when the turn signal is in operation. 6) Engine oil pressure warning light ( red ). Illuminates when engine oil pressure is too low. This light should illuminate when the ignition is switched to ON and should go out a few seconds after the engine starts. Important If this light (6) stays on, stop the engine to avoid serious damage. 7) High beam warning light ( blue ). Illuminates when the high beam headlight is on. 8) “EOBD engine diagnostics light” ( amber ). The engine ECU iluminates this light steadily to indicate the presence of errors leading to engine lock. 9) OVER REV indicator lights . Illuminates steadily at 800 rpm before intervention of the revlimiter. Starts flashing when the rev limiter is reached. 5 8 2 4 9 3 1 6 7 fig. 4 12 E 10) 2-position switch A and B . Switch used for displaying and setting instrument panel parameters. It has two positions, A “▲” and B “▼”. 11) High beam headlight flasher switch (fig. 5). The high beam headlight flasher switch is also used for the LAP and USB data aquisition functions. 11 A 10 B fig. 5 13 E LCD – Main functions Warning Any adjustments to the instrument panel must only be carried out when the motorcycle is stationary. Never operate the instrument panel controls while riding the motorcycle. 1) Speedometer . Indicates road speed. 2) Odometer . Shows total distance travelled. 3) Trip meter . Indicates the distance travelled since last reset. 4) Fuel reserve trip counter . Shows distance travelled on reserve fuel. 5) Clock . 6) Air temperature indicator . 7) Lap time . 8) Rev counter (RPM) . 9) Lap time . 8 11 13 12 14 10 4 5 9 6 2 3 1 7 fig. 6 14 E 10) Service indicator (fig. 6). The indicator illuminates to signal when a service is due. The service indiactor will remain on the display until the system is reset by the Ducati Service Centre who carry outthe service. 11) LAP function (fig. 6). Indicates that the LAP has been activated. 12) DDA function (fig. 6). Indicates that the Ducati Data Analyzer (DDA) has been activated. Important The instrument panel incorporates diagnostic functions for the electronic injection/ignition system. The relative menus are for the use of trained personnel only. If you accidentally access this function, turn the key to OFF and have the motorcycle checked at an authorised Ducati Service Centre. 13) Oil temperature indicator (fig. 6). Important Stop riding if the temperature reaches the maximum value, otherwise the engine might be damaged. 14) Ducati Traction Control (DTC) (fig. 6). Indicates activation of the DTC control unit (if present). 15 E LCD – How to set/display parameters At key-on (key turned from OFF to ON ) the instrument panelactivates all the digits of the LCD for 1second and switches on the indicator lights in sequence.

Incoming search terms:

Yamaha VMX12/ VMX12C Owner's Manual

0

Filed Under (Yamaha) by admin on 14-12-2010

download
Main switch EAUO0028 The main switch controls the ignition and lighting systems. The various main switch positions are described below. EAU00032 ON All electrical systems are supplied with power, the headlight, meter lighting, taillight and front position lights come on, and the engine can be started. The key cannot be removed. EAU00038 OFF All electrical systems are off. The key can be removed. 1. Push. 2. Release. 3. Turn P (Parking) The meter light, taillight and position lights are on, but all other electrical sys- tems are off. The key can be removed. The key must be pushed in from the “OFF” position to be turned to “P”. ECA00043 Do not use the parking position for an extended length of time, otherwise the battery may discharge. 1. Neutral indicator light ‘NEUTRAL’ 2. Turn signal indicator light ‘TURN’ 3. Fuel level warning light ‘FUEL’ 4. High beam indicator light ‘HIGH BEAM’ 5. Oil level warning light ‘OIL LEVEL’ EAU03034 Indicator and warning lights EAU00062 Neutral indicator light “NEUTRAL” This indicator light comes on when the transmission is in the neutral position. EAU00059 Turn signal indicator light “TURN” This indicator light flashes when the turn signal switch is pushed to the left or right. his warning light comes on when the fuel level drops below approximately 3 L (0.7 Imp gal, 0.8 US gal). When this occurs, refuel as soon as possible. The electrical circuit of the warning light can be checked according to the fol- lowing procedure. 1. Turn the key to “ON”. 2. If the warning light does not come on, have a Yamaha dealer check the electrical circuit. Oil level warning light “OIL LEVEL” This warning light comes on when the engine oil level is low. The electrical circuit of the warning light can be checked according to the following procedure. 1. Turn the key to “ON”. 2. If the warning light does not come on, have a Yamaha dealer check the electrical circuit. NOTE: EAU00064 High beam indicator light “HIGH BEAM” This indicator light comes on when the high beam of the headlight is switched on. Even if the oil level is sufficient, the warning light may flicker when riding on a slope or during sudden acceleration or deceleration, but this is not a mal- function

Incoming search terms:

YAMAHA FJR1300N OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 12-12-2010

download
3-2 3 EAU03034 Indicator and warning lights EAU04121 Turn signal indicator lights “” a n d “” The corresponding indicator light flashes when the turn signal switch is pushed to the left or right. EAU00061 Neutral indicator light ” ” This indicator light comes on when the transmission is in the neutral position. EAU00063 High beam indicator light ” ” This indicator light comes on when the high beam of the headlight is switched on. EAU03201 Oil level warning light ” ” This warning light comes on when the engine oil level is low. The electrical circuit of the warning light can be checked according to the fol- lowing procedure. 1. Set the engine stop switch to ” ” and turn the key to “ON”. 2. Shift the transmission into the neu- tral position or pull the clutch lever. 3. Push the start switch. If the warning light does not come on while push- ing the start switch, have a Yamaha dealer check the electrical circuit. NOTE: Even if the oil level is sufficient, the warning light may flicker when riding on a slope or during sudden acceleration or deceleration, but this is not a mal- function. EAU03192 Engine trouble warning light ” ” This warning light comes on or flashes when an electrical circuit monitoring the engine is defective. When this oc- curs, have the Yamaha dealer check the self-diagnosis system. The electrical circuit of the warning light can be checked according to the fol- lowing procedure. 1. Set the engine stop switch to ” “. 2. Turn the key to “ON”. If the warn- ing light does not come on, have a Yamaha dealer check the

Incoming search terms:

YAMAHA YZF-R1R/ YZF-R1RC OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 03-12-2010

download
1. Right turn signal indicator light “” 2. Fuel level warning light “” 3. Oil level warning light “” 4. Neutral indicator light “” 5. Engine trouble warning light “” 6. High beam indicator light “” 7. Left turn signal indicator light “”
INSTRUMENT AND CONTROL FUNCTIONS 3-3 3 EAU04895 Oil level warning light “” This warning light comes on when the engine oil level is low. The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical cir- cuit. NOTE: Even if the oil level is sufficient, the warning light may flicker when riding on a slope or during sudden acceleration or deceleration, but this is not a malfunction. This model is also equipped with a self-diagnosis device for the oil level detection circuit. If the oil level detection circuit is defective, the following cycle will be repeated until the malfunction is corrected: The oil level warning light will flash ten times, then go off for 2.5seconds. If this occurs, have a Yamaha dealer check the motor- cycle. EAU00061 Neutral indicator light “” This indicator light comes on when the transmission is in the neutral position. EAU04896 Engine trouble warning light “” This warning light comes on or flashes when an electrical circuit monitoring the engine is defective. When this occurs, have a Yamaha dealer check the self-diagnosis system. (See page 3-7 for an explanation of the self-diagnosis device.) The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical circuit. EAU00063 High beam indicator light “” This indicator light comes on when the high beam of the headlight is switched on

Incoming search terms:

YAMAHA XV1700 PCR/ XV1700 PCRC OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 02-12-2010

download
High beam indicator light “” 2. Right turn signal indicator light “” 3. Fuel level warning light “” 4. Engine trouble warning light “” 5. Left turn signal indicator light “” 6. Neutral indicator light “” 1. Speedometer INSTRUMENT AND CONTROL FUNCTIONS 3-4 3 EAU04436 Tachometer unit The electric tachometer allows the rider to monitor the engine speed and keep it within the ideal power range. The tachometer unit is equipped with the following: ● an odometer (which shows the total distance traveled) ● two tripmeters (which show the distance traveled since they were last set to zero) ● a fuel reserve tripmeter (which shows the distance traveled since the fuel level warning light came on) ● a meter lighting control ● a clock ● a self diagnosis device NOTE: ● Be sure to turn the key to “ON” before using the “SELECT” and “RESET” buttons. ● To switch the odometer, the trip- meters and the fuel reserve trip- meter displays between kilometers and miles, press the “SELECT” button for at least two seconds. ECA00123 CAUTION: Do not operate the engine in the tachometer red zone. If operated in the red zone, the tachometer segments will start flashing to notify the rider. Red zone: 5,000 r/min and above 1. Tachometer 2. Clock 3. Odometer/tripmeter/fuel reserve tripmeter 4. “RESET” button 5. “SELECT” button 1. Tachometer red zone
INSTRUMENT AND CONTROL FUNCTIONS 3-5 3 Odometer and tripmeter modes Pushing the “SELECT” button switches the display between the odometer mode”ODO” and the tripmeter modes “TRIP 1″ and “TRIP 2″ in the following order: ODO→ TRIP 1 → TRIP 2 → ODO If the fuel level warning light comes on (see page 3-2), the odometer display will automatically change to the fuel reserve tripmeter mode “TRIP F” and start counting the distance traveled from that point. In that case, pushing the “SELECT” button switches the display between the various tripmeter and odometer modes in the following order: TRIP F → TRIP 1 → TRIP 2 → ODO → TRIP F To reset a tripmeter, select it by pushing the “SELECT” button, and then push the “RESET” button for at least one second. If you do not reset the fuel reserve tripmeter manually, it will reset itself automatically and the display will return to the prior mode after refueling and traveling 3mi (5km). Meter lighting control mode 1. Turn the key to “OFF”. 2. Push and hold the “SELECT” but- ton. 3. Turn the key to “ON”, and then after five seconds, release the “SELECT” button. 4. Push the “RESET” button to select the desired brightness. 5. Push the “SELECT” button to set the brightness level. 6. Turn the key to “OFF”. NOTE: When adjusting the meter lighting, the odometer display will indicate the brightness level. Clock mode To set the clock: 1. Push the “SELECT” button and “RESET” button together for at least two seconds. 2. When the hour digits start flashing, push the “RESET” button to set the hours. 3. Push the “SELECT” button, and the minute digits will start flashing. 4. Push the “RESET” button to set the minutes. 5. Push the “SELECT” button and then release it to start the clock. NOTE: ● After setting the clock, be sure to push the “SELECT” button before turning the key to “OFF”, otherwise the clock will not be set. ● To set the clock after the battery has been disconnected, first set the time to 1:00 AM, and then set the clock to the correct time

Incoming search terms:

BMW S1000 RR Rider's Manual

0

Filed Under (BMW) by admin on 28-11-2010

download
Standard status indicators Multifunction display 1 Speedometer 2 Coolant temperature 3 Clock (37) 4 Odometer and tripmeters (38) 5 Ride mode (43) 6 Gear indicator (20) Telltale lights 1 Flashing turn indicators, left 2 Flashing turn indicators, right 3 Idle 4 High-beam headlight Gear indicator The gear engaged or Nforneut- ralappearsonthe display. If no gear is engaged, the ‘neutral’telltale light also lights up. Service-due indicator If the next service is due in less than one month, the date for the next service is shown briefly after the Pre-Ride Check completes. Month 1 and year 2 are shown; in this example the read- ingmeans”August 2010″. 3 If the motorcycle covers long dis- tancesinthe course of the year, under certain circumstances it might be necessary to have it serviced at a date in advance of the forecast due date. If the countdown distance to the odometer reading at whichaservice will be due is less than 1000 km, the distance is counted down in steps of 100kmandisshown briefly after the Pre-Ride Check completes. If service is overdue, the due date or the odometer reading at which service was due is accom- paniedbythe’General’warning light showing yellow. The word “Service”remains permanently visible. If the sevice-due indicator appears more than a month before the service date, the date saved in the instrument cluster must be adjusted. This situation can occur if the battery was disconnected fora prolonged period of time. If you want to have the date set consulta specialist workshop, preferably an authorised BMW Motorraddealer. Standard warnings Mode of presentation Warnings are output byawarning light 1 or indicated byawarning string in the display.