Harley Davidson Handlebar Top Clamp Instruction Manual

0

Filed Under (Harley Davidson) by admin on 13-04-2012

download
Mounting of the Handlebar Top Clamp • Mount the motoscope mini to the handlebar top clamp by using the enclosed metric countersunk screws (M3). Do not exceed the maximum tightening torque which is 4 Nm. • Laying both cables of the motoscope mini and indicator lights through the clamp inner groove in rear direction (to the driver). • Mark the position of the handlebar to the lower handlebar retainer with a marker pen. Undo the 4 clamping bolts and remove the original top clamp. • Put the motogadget handle bar clamp onto the handle bar and align the handle bar according the pen marking. Make sure both cables are still located in the groove; otherwise the cable will be damaged. • Then put the enclosed inch screws into the 4 drillings and tighten them crosswise and evenly. Take care that the gap between the upper and lower handlebar clamp remains the same at each point. A maximum torque for the inch screws of 20 Nm must not be exceeded. Connection and cable colours Before starting the electrical connection remove the vehicle battery or interrupt its connection to the onboard power supply. Use the original vehicle wiring diagram. Then connect the warning lights as described in the table below. If you have two indicator control lights see the wiring diagram below for joining them to one control light. Make sure all connections are fused. If you don’t fuse it properly, a damage of the connection cable can cause a cable fire. Make sure you are capable to connect the instrument properly. If you are not sure, let the professional shop do the job

2004 Camry, Highlander & Solara OCCUPANT CLASSIFICATION SYSTEM INITIALIZATION

0

Filed Under (Toyota Manuals) by admin on 07-10-2011

download
Occupant Classification System (OCS) that will enable or disable the passenger front and side airbags based on occupancy, passenger weight and seat belt latch position. Passenger front and side airbags will automatically be disabled for children and small adults when weight on the seat is less than approximately 80 lbs. (36 kg). This system will clearly indicate that the passenger airbags are enabled “ON” or disabled “OFF.” Early production models of the 2004 Solara were built with an amber-colored PASSENGER AIRBAG light. To better differentiate the PASSENGER AIRBAG light from warning lights, it has been changed to white in color. This color change does not have any effect on the meaning or operation of the light. This light remains on at all times with the key in the ON position. In the event of an OCS malfunction, both the Supplemental Restraint System (SRS) warning light and passenger airbag “OFF” indicator lights will illuminate. After finding SRS code B1650 on Camry and Solara vehicles, or a B1150 on Highlander vehicles, the next step is to check codes in the OCCUPANT DETECT menu on the Diagnostic Tester. Take necessary steps to diagnose the root cause of the OCS DTC code BEFORE initializing the system

Incoming search terms:

Toyota Avensis Equipment REMOVAL AND INSTALLATION

0

Filed Under (Toyota Manuals) by admin on 05-10-2011

Trip computer with fuel consumption &average speed display (where standard audio fitted) Outside temperature display Instrument display dimmer Digital odometer with two trip meters Digital Clock Dashboard integrated multi-information display (where standard audio fitted) Fuel Caplocation indicator Rearfoglamps indicator Sequential automatic transmission mode indicator (where sequential automatic fitted) Tachometer Fuel indicator with low fuel warning Water temperature indicator Engine temperature warning Engine management warning Lights Onwarning Door Ajarwarning



YAMAHA FZS6W OWNER’S MANUAL

0

Filed Under (Yamaha) by admin on 27-04-2011

download
Indicator and warning lights EAU11030 Turn signal indicator lights “ ” and “ ” The corresponding indicator light flashes when the turn signal switch is pushed to the left or right. EAU11060 Neutral indicator light This indicator light comes on when the transmission is in the neutral position. EAU11080 High beam indicator light This indicator light comes on when the high beam of the headlight is switched on. EAU11250 Oil level warning light This warning light comes on when the engine oil level is low. The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical circuit. NOTE: ● Even if the oil level is sufficient, the warning light may flicker when riding on a slope or during sudden acceleration or deceleration, but this is not a malfunction. ● This model is also equipped with a self-diagnosis device for the oil level detection circuit. If the oil level detection circuit is defective, the following cycle will be repeated until the malfunction is corrected: The oil level warning light will flash ten times, then go off for 2.5 seconds. If this occurs, have a Yamaha dealer check the vehicle. EAU11423 Coolant temperature warning light “ ” This warning light comes on when the engine overheats. When this occurs, stop the engine immediately and allow the engine to cool. The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical cir

Yamaha VMX12/ VMX12C Owner's Manual

0

Filed Under (Yamaha) by admin on 14-12-2010

download
Main switch EAUO0028 The main switch controls the ignition and lighting systems. The various main switch positions are described below. EAU00032 ON All electrical systems are supplied with power, the headlight, meter lighting, taillight and front position lights come on, and the engine can be started. The key cannot be removed. EAU00038 OFF All electrical systems are off. The key can be removed. 1. Push. 2. Release. 3. Turn P (Parking) The meter light, taillight and position lights are on, but all other electrical sys- tems are off. The key can be removed. The key must be pushed in from the “OFF” position to be turned to “P”. ECA00043 Do not use the parking position for an extended length of time, otherwise the battery may discharge. 1. Neutral indicator light ‘NEUTRAL’ 2. Turn signal indicator light ‘TURN’ 3. Fuel level warning light ‘FUEL’ 4. High beam indicator light ‘HIGH BEAM’ 5. Oil level warning light ‘OIL LEVEL’ EAU03034 Indicator and warning lights EAU00062 Neutral indicator light “NEUTRAL” This indicator light comes on when the transmission is in the neutral position. EAU00059 Turn signal indicator light “TURN” This indicator light flashes when the turn signal switch is pushed to the left or right. his warning light comes on when the fuel level drops below approximately 3 L (0.7 Imp gal, 0.8 US gal). When this occurs, refuel as soon as possible. The electrical circuit of the warning light can be checked according to the fol- lowing procedure. 1. Turn the key to “ON”. 2. If the warning light does not come on, have a Yamaha dealer check the electrical circuit. Oil level warning light “OIL LEVEL” This warning light comes on when the engine oil level is low. The electrical circuit of the warning light can be checked according to the following procedure. 1. Turn the key to “ON”. 2. If the warning light does not come on, have a Yamaha dealer check the electrical circuit. NOTE: EAU00064 High beam indicator light “HIGH BEAM” This indicator light comes on when the high beam of the headlight is switched on. Even if the oil level is sufficient, the warning light may flicker when riding on a slope or during sudden acceleration or deceleration, but this is not a mal- function

Incoming search terms:

YAMAHA FJR1300N OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 12-12-2010

download
3-2 3 EAU03034 Indicator and warning lights EAU04121 Turn signal indicator lights “” a n d “” The corresponding indicator light flashes when the turn signal switch is pushed to the left or right. EAU00061 Neutral indicator light ” ” This indicator light comes on when the transmission is in the neutral position. EAU00063 High beam indicator light ” ” This indicator light comes on when the high beam of the headlight is switched on. EAU03201 Oil level warning light ” ” This warning light comes on when the engine oil level is low. The electrical circuit of the warning light can be checked according to the fol- lowing procedure. 1. Set the engine stop switch to ” ” and turn the key to “ON”. 2. Shift the transmission into the neu- tral position or pull the clutch lever. 3. Push the start switch. If the warning light does not come on while push- ing the start switch, have a Yamaha dealer check the electrical circuit. NOTE: Even if the oil level is sufficient, the warning light may flicker when riding on a slope or during sudden acceleration or deceleration, but this is not a mal- function. EAU03192 Engine trouble warning light ” ” This warning light comes on or flashes when an electrical circuit monitoring the engine is defective. When this oc- curs, have the Yamaha dealer check the self-diagnosis system. The electrical circuit of the warning light can be checked according to the fol- lowing procedure. 1. Set the engine stop switch to ” “. 2. Turn the key to “ON”. If the warn- ing light does not come on, have a Yamaha dealer check the

Incoming search terms: