HARLEY DAVIDSON XL (Sportster) ENGINE GUARD INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-04-2011

download
Installation- Late 1984 and Later XLModels (Equipped With Alternator) 1 CAUTION Late 1994 and 1995 XL vehicle nut plates have 3/8-16 threads. Reuse original screws on late 1994 and 1995 XL models. Installing the 3/8-24 x 1-1/4 in. screws from kit will damage nut plate and screw threads. 1. See Figure 1. From underside of steering head remove screws (7, 8, or 9) and flat washer (6). Discard original screws (7, 8, or 9) and washer (6). 2. Remove and discard the two top motor mount screws, washers, and nuts. 3. See Figures 1 and 2. Place washer (2) on 5-1/2 in. long screw (1). Insert screw (1) through one motor mount, through spacer (11) (unless engine guard is being installed on a vehicle equipped with forward controls, in which case DO NOT USE SPACER), through the offset end of bracket (3), and (with large offset toward jiffy stand side of vehicle) through the other motor mount. Place kit supplied washer (2) on end of screw (1) and secure with locknut (4). Be sure bracket does not pinch wiring. On 1986 and later models be sure bracket does not contact oil pressure switch. 4. See Figure 1. Position engine guard (5) upper mounting bracket under the steering head

HARLEY DAVIDSON MOUNTING BRACKET SERVICE MANUAL

0

Filed Under (Harley Davidson) by admin on 12-04-2011

download
INSTALLATION 1. See Figure 1. Note position of mounting brackets (1). Remove old mounting brackets and discard. NOTE On 1997-2000 models, the air fittings are installed to the two mounting holes on the right-hand right side bracket. On 2003 and later models, the single air fitting is installed to mounting hole on the left-hand side bracket. 2. See Figure 2. Install new mounting brackets from kit on each side of the motorcycle using new locknuts as follows: a. Use the 5/16-18 x 1 inch screws (5) in the upper two holes with 2 chrome washers (3) placed between the mounting bracket and the saddlebag support at each of the two locations. Install a 5/16-18 flange locknut (2) behind the screw that does not screw into a weld nut. Tighten to 15-19 ft-lbs (20-26 Nm). b. On each side, install a 1/4-20 x 7/8 inch screw (9) through the bottom hole of the mounting bracket and the saddlebag bracket as shown, with a chrome washer (3) placed between the mounting bracket and the saddlebag bracket. Tighten to 10-14 ft-lbs (13.5- 19.0 Nm). On 1997-2002 models, install the air line fittings to the lowest two holes drilled in the right side bracket. On 2003 and later models, install the single air line fitting to the lower front hole drilled on the left side bracket. c. See Figure 2. On each side, attach docking points (6) in their proper location on mounting bracket with 3/8- 16 x 1-1/2 in. buttonhead screws (7), washers (3) and locknuts (8) but leave locknuts slightly loose so docking points can be adjusted for proper fit. On 1997and later models, the docking point will attach through the front hole of the mounting bracket as shown. On 1994-1996 models, the docking point will attach through the rear hole of the mounting bracket. d. Place detachable passenger backrest into docking points as described in the Backrest Instruction Sheet. Make sure that the forward notches of the sideplates are pushed completely into the forward docking points, then tighten the rear docking points securely to 45-47 ft/lbs (61.0-64.0 Nm

Incoming search terms:

HARLEY DAVIDSON FLSTN MUFFLER SLIP-ON KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 12-04-2011

download
Installation To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Disconnect negative battery cable. Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) 2. Remove mufflers according to applicable Service Manual instructions. 3. Install clamps onto mufflers and slide onto headpipes. Install muffler with the Harley Davidson script in the top position. 1 WARNING 1 WARNING 1 of 2 4. See Service Parts Illustration: Reuse fasteners and tighten muffler clamps to 45-60 ft-lbs (61-81.3 Nm), and tighten screws and washers to 15-19 ft-lbs (20.3-25.8 Nm). 5. Connect negative battery cable. Tampering Prohibition Federal law prohibits any modification to this exhaust system which causes the motorcycle to exceed the Federal noise standard. Use of the motorcycle with such a modified exhaust system is also prohibited. NOTE This product should be checked for repair or replacement if the motorcycle noise has increased significantly through use. Otherwise, the owner may become subject to penalties under state and local ordinances.

HARLEY DAVIDSON DYNA DOCKING HARDWARE FOR FXDX WITH WIDE TIRE INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-04-2011

download
Installation NOTE Perform the following procedures on one side of the motorcycle until instructed to go to the other side. To keep fender in alignment the front docking point will be mounted first. INSTALLING DOCKING POINTS NOTE Save the acorn nuts and washers removed from the fender support bracket for use when installating docking points. 1. Loosen and remove the acorn nuts, washers, and screws from the fender support (right-hand) bracket. Save the washers and acorn nuts for docking point installation. Discard screws. 2. Obtain 1 plastic bushing, labeled 01, from a bushing set. 3. Place the bushing (4) (beveled side out) into the front support hole as shown in Service Parts illustration. 4. Place the countersunk side of the front docking point (2) so that it engages bushing (4). 5. From underneath (inside) the fender, insert hex-head screw (1) through fender, support bracket and front docking point (2). 6. Install washer (7) split lockwasher (5) and acorn nut (6) to screw and tighten to 27 ft-lbs (37 Nm). Take care to avoid scratching or marring component finish. 7. Obtain another plastic bushing, labeled 01 , from the bushing set. 8. Place bushing (4) (beveled side out) into the the rear support hole as shown in Service Parts illustration. 9. Place the countersunk side of the rear docking point (3) so that it engages bushing (4). 10. From underneath (inside) the fender, insert hex-head screw through fender, support bracket and rear docking point (3). 11. Install washer (7) split lockwasher (5)and acorn nut (6) to screw and tighten to 27 ft-lbs (37 Nm). Take care to avoid scratching or marring component finish. 12. Repeat procedures 1 through 11 for opposite (left-hand) side of the motorcycle. NOTE In time docking points may wear, causing the sideplates to become loose. The fit may be tightened using the following procedure. 1. Loosen docking hardware. 2. Rotate docking points clockwise approximately 45°. 3. Tighten docking hardware to the appropriate torque values. Repeat as often as required, up to 3 times

Incoming search terms:

ARLEY DAVIDSON FXDL INSTRUMENT CONSOLE INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 28-03-2011

download
Installation CONSOLE REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative cable first) before proceeding. Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury (00049a). 1. Remove seat and disconnect battery, negative cable first. 2. Remove fuel tank mounting bolts. Lift fuel tank far enough to remove the speedometer sensor cable from the mounting clips under the tank. 3. See Figure 1. The 3-place speedometer sensor connector is located on the frame beneath the seat. Remove from t-stud and disconnect the connector. Cut the cable strap that holds sensor wires to right rear frame tube. 4. Remove instrument console mounting screws and lift console from tank. SPEEDOMETER REMOVAL 1. See Figure 2. Disconnect 8-place connector under console. Remove assembly from tank. 2. Cut remaining cable straps holding wires to instrument mounting bracket. Remove screws holding bracket to back of instruments. Remove bracket. 3. See Figure 3. Remove nuts and washers from terminal studs (1, 2 and 3). Remove wires from studs. 4. Unscrew the rubber function switch cover that protrudes from the left side of the console. Remove the function switch (3). 5. Gently push on bottom of speedometer and remove speedometer from top side of console. Remove gasket from speedometer. TACHOMETER REMOVAL 1. See Figure 3. Remove nuts and washers from terminal studs (3, 4 and 5). Remove wires from studs. 1 WARNING 1 WARNING

HARLEY DAVIDSON DYNA GLIDE FRONT SPOILER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-03-2011

download
INSTALLATION Assemble Front Spoiler and Bracket 1. See Figure 1. Position front spoiler as shown and orient bracket (1) with the angled end toward the top of the spoiler. 2. Install two screws (2) and washers (3) to secure upper part of bracket to spoiler. Tighten to 15-20 in-lbs (1.7-2.3 Nm). 1 3 2 2 3 is04350 1. Bracket 2. Screw (2) 3. Washer (2) Figure 1. Assemble Top of Bracket to Spoiler 2 1 3 1 2 is04351 1. Screw (2) 2. Washer (2) 3. Bracket Figure 2. Assemble Bottom of Bracket to Spoiler 3. See Figure 2. From the bottom of the spoiler, loosely install screws (1) and washers (2) into formed nut on bracket (3). This will allow for adjustments (if necessary) after installing the spoiler to the lower frame crossmember. Install Front Spoiler Assembly NOTES When removing engine mount screws, use a small bottle jack or similar device (placed directly under the crankcase) to hold the engine in position and maintain hole alignment between the front engine mounts and holes in the lower frame cross- member. If this safety measure is not followed, the engine may shift slightly making it difficult to align the front engine mount and new screws. 1. See Figure 3. Remove and discard existing bottom screw (1), lockwasher (2), and washer (3) from engine mount (4) at lower frame crossmember. 2. See Figure 4. Thread screw (1) and lockwasher (2) into bottom hole of lower frame crossmember until about 5/8 in. (3) remains visible. 3. Remove and discard existing top hardware (screw, lock- washer, and washer) (4) from engine mount (5).

HARLEY DAVIDSON CHROME TRANSMISSION HARDWARE KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 17-03-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Disconnect battery cable, negative (-) cable only. NOTE The starter does not need to be removed to install this kit. 2. Remove exhaust system only if needed to access transmission top cover hardware. Refer to Service Manual for instructions. NOTES Replace existing zinc hardware with chrome-plated hardware one at a time so the transmission top and side covers do not need to be replaced. 3. Remove and discard existing six 1/4-20 x 1 in. hex socket- head screws and washers from top transmission cover. Install six chrome hex socket head screws (1) and washers (2) on top transmission cover (3). Tighten to 84-108 in-lbs (9.5-12.2 Nm). 4. Remove and discard existing two 1/4-20 x 1 in. hex socket head screws and washers from side transmission cover. Install two chrome hex socket head screws (1) and washers (2) on side transmission cover (5). Tighten to 84- 108 in-lbs (9.5-12.2 Nm). 5. Remove and discard existing four 1/4-20 x 1-1/2 in. hex socket head screws and washers from side transmission cover. Install four chrome hex socket head screws (4) and washers (2) on transmission side cover (5). Tighten to 84- 108 in-lbs (9.5-12.2 Nm). 6. Install exhaust system if previously removed. Refer to Service Manual for instructions. 7. Connect negative (-) battery cable

HARLEY DAVIDSON DYNA SPRING SEAT MOUNTING KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-03-2011

download
INSTALLATION 1. Refer to service manual and remove the existing seat. 2. See Figure 2. Install the frame cover (9) to the frame and secure with fastener (4). Orient the frame cover to so that it covers the seat pan. 3. Install two springs (2) to the mounting bracket (1), oriented as shown, with screws (3). Tighten screws to 25-30 ft-lbs (34-41 Nm) . 4. Install mounting bracket to frame as follows: a. Remove two screws from the rear of the seat pan area where the spring seat mounting bracket (1) will be mounted. Save washers for later installation. b. Install mounting bracket (1) to the frame over the frame cover. Orient the frame cover so that it will be retained by the mounting bracket when secured. c. Secure the left side of the mounting bracket to the frame with a screw (7), stock washer (B) and spacer (8). Do not tighten. d. Secure the right side of the mounting bracket to the frame with a screw (7) and stock washer (B). e. Tighten mounting bracket screws to 90-108 in-lbs (10-12 Nm) . 5. Install seat pivot bracket (10), washers (15) and screws (5) to the seat. Tighten screws to 48-72 in-lbs (5.5-8.0 Nm) . 6. Remove the rear fuel tank mounting screw, washers, nut and thread protector. Save washers for later installation

HARLEY DAVIDSON VRSCF RIGID SADDLEBAGS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-03-2011

download
Kit Contents See Figure 5 and Table 1. PREPARATION To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Refer to the service manual and follow the instructions given to remove the main fuse. 2. Remove the rider seat and passenger pillion per the instructions in the service manual. 3. See Figure 1. Remove the four rear fender mounting bolts (1) and washers (2), and the passenger grab strap (3). If necessary, move the ECM to better access the fender mounting bolts. 1 3 2 is05463a 1. Bolt (4) 2. Washer (4) 3. Grab strap Figure 1. Fender Mounting Bolts 4. Disconnect the six-way tail lamp socket housing and four- way turn signal lamp socket housing from the vehicle main harness following the instructions in the service manual. Disconnect the two-way license-plate illuminator socket housing from the tail lamp harness. 5. If a luggage rack, sissy bar upright or both have been mounted on the rear fender , remove the two screws and washers, and two carriage bolts and nuts that secure the luggage rack bracket to the seat pan. NOTE The rack and/or upright will remain attached to the rear fender when the fender is removed. 6. Remove the rear fender from the seat pan by lifting upward and sliding the fender back. 7. If a center-mounted license bracket is installed, it can remain attached to the seat pan. If a side-mounted license bracket is installed: a. Remove the license plate from the vehicle (if installed), and set aside for later installation. b. See Figure 2. Remove the two bolts (8) holding the side license-plate bracket (1) to the seat pan (9). c. Remove the license-plate adjuster bracket (2) carriage bolt (3), washer (4) and lock nut (5), and the license- plate illuminator (6) and screws (7) from the bracket. d. The original equipment (OE) license-plate bracket (1), screws (7) and bolts (8) can be discarded. Set the remaining items aside for installation to the new side license-plate bracket. 8. Remove and discard the rear side reflectors (10). If a center-mounted license bracket is installed, remove the reflectors from the license bracket sides. Remove any residual adhesive from the bracket. If a side-mounted license bracket is installed, remove the reflectors from the upper frame just forward of the shock absorbers. Remove any residual adhesive from the reflector mounting area on the frame. NOTE Access to the shock absorber adjustment collar is more difficult with the saddlebags in place. 9. Adjust the rear suspension preload, if desired, per the instructions in the service manual

HARLEY DAVIDSON SOFTAIL FRONT SPOILER KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 09-03-2011

download
This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Kit Contents See Figure 2 and Table 1. INSTALLATION 1. Position the vehicle on a motorcycle lift table. To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 2. Refer to the Service Manual and follow the instructions given to remove the Maxi® Fuse. 3. Raise the vehicle on the lift table to allow access to the lower front portion of the frame. 2008+ 2007 7 8 11 3 3 4 4 12 5 5 1 1 9 2 2 10 6 6 9 9 11 13 is02652c 8. 1. Two-pin voltage regulator connector (2007 only) Voltage regulator 2. 9. Voltage regulator attaching screws (2) Cable strap (2 for 2007, 1 for 2008 and later) 10. 3. Lower voltage regulator cover (2007 only) Voltage regulator bracket 4. 11. Bracket screw to engine crankcase (2) Oxygen sensor connector 12. 5. Crank position sensor connector (2007 only) Voltage regulator caddy 6. 13. Voltage regulator caddy cover Horn connectors (some 2008 and later models) 7. Four-pin voltage regulator connector (2007 only) Figure 1. Original Equipment Voltage Regulator  NOTE For 2007 models: The ground wire on the voltage regulator must be re-attached at the original location when re-installing the voltage regulator to ensure adequate ground. 4. For ALL models: See Figure 1. Remove and discard the voltage regulator caddy cover (6) from the regulator bracket (3) and caddy (5). For 2007 models: In addition, remove the lower voltage regulator cover (10). 5. Remove and retain the hex socket head screw (4) at the top left of the bracket For 2007 models: In addition, disconnect the ground wire. Free the cable straps (9) from the regulator bracket, beneath the regulator. 6. Remove the two hex socket head screws with washers (2) retaining the voltage regulator to the bracket. Remove and save the regulator, but discard the screws. 7. Remove and retain the screw (4) at the top right of the regulator bracket. Remove the bracket from the engine. 8. For 2008 and later models: Free the strap (9) that ties the jiffy stand wiring to the voltage regulator bracket. Unfasten the three-way jiffy stand sensor connector and the two-way crank position sensor connector [79] (12) from the T-studs on the back of the regulator bracket (3). Discard the bracket. Disconnect both plugs from the back of the voltage regulator (1). For 2007 models: Unfasten the four-way (7) and two-way (8) voltage regulator connectors from the T-studs on the back of the regulator bracket (3), and discard the bracket. Disconnect the voltage regulator (1) at both connectors. 9. For 2008 and later models: Unclip the two-way O 2 (oxygen) sensor electrical connector [138] (11) from the voltage regulator caddy (5). For 2007 models: Unfasten the two-way crank position sensor connector [79] (12) from the voltage regulator caddy (5). Remove the caddy from the vehicle frame. a. For 2007 models: Unclamp the bottom of the caddy from the engine mount spacers. b. For ALL models: Unhook the top clips from around the tabs on the front of the engine casting. Remove the original equipment (O.E.) caddy from the vehicle frame, and discard it.

Incoming search terms: