HARLEY DAVIDSON FAIRING BRA INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 05-02-2011

download
This kit is designed for installation on 1996 and later FLHT, FLHTC, FLHTCU AND FLHTCU/I Model Motorcycles. Installation 1. Align each of the sewn-in pockets on the fairing bra with each of the outer edges of the fairing at handlebar level. 2. See Figure 1. Standing in front of the vehicle, remove the three T27 Torx screws (1) with washers securing the windshield along the front of the fairing. NOTE In the following Step, the Chrome Windshield Strip (purchased separately) , will serve as a mounting bracket for the fairing bra 3. Obtain the Chrome Windshield Strip (P/N 59213-96) and screws supplied with strip. While aligning holes in the chrome strip over the bra, install the new screws with washers through the strip and bra, then tighten securely into the windshield. 4. The six straps (three on each side near the bottom) will be captured between the inner and outer fairing. Refer to Figure 1. Remove the four screws (2) from the inner fairing. NOTE: The bottom two screws are below the fairing cap. Save screws for installation. Separate the inner and outer fairings just enough to install the straps into the fairing. Adjust the straps, then reinstall the screws and tighten securely. 5. Remove the Phillips screw located at the bottom of the headlamp trim ring. Save screw for installation 6. See Figure 2. Orient the elastic portion of the bra around the headlamp, however in front of, the retaining ring as shown. 7. Install the bottom elastic strap below the fairing seal under the headlamp. 8. Install the headlamp trim ring using the Phillips screw removed in Step 5.

HARLEY DAVIDSON SCREAMIN' EAGLE MECHANICAL COMPRESSION RELEASE FIX- TURE

0

Filed Under (Harley Davidson) by admin on 04-02-2011

download
DRILLING AND TAPPING PROCEDURE Wear safety glasses or goggles while drilling. Flying debris could result in serious eye injury. (00565b) NOTE Perform the following procedure on both the front and rear cylinder heads. Tool Setup NOTE Due to slight manufacturing differences, it may be necessary to tap the fixture into place with a rubber mallet. Do NOT use excessive force. 1. Align the fixture’s locating pins with the 3/8 inch tooling holes in the head and install the fixture on the head. 2. See Figure 1 and Figure 6. Secure the fixture (1) to the head with two 5/16-18 socket head cap screws (2) and washers (9) included in the kit. Install the screws in the holes marked “F” when modifying the front head or in the holes marked “R” when modifying the rear head. Tighten screws to 80 in-lbs (9 Nm) . 3. See Figure 3 and Figure 6. Install the drill bushing (3) in the bore marked “FRONT” when modifying the front head or in the bore marked “REAR” when modifying the rear head. 4. Tighten drill bushing set screw to 50 in-lbs (5.6 Nm) . 5. See Figure 2 and Figure 6. Install collar stop (4) onto the 1/2 inch diameter shank of the step drill bit (5). Secure the collar stop with the set screw 3.900 inches (9.90 cm) from the beginning of the 3/4 inch diameter step of the drill bi

HARLEY DAVIDSON SCREAMIN' EAGLE ELECTRONIC FUEL INJECTION (EFI) STAGE 1 KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 04-02-2011

download
Installation NOTE The installation procedure is divided into three parts: 1) Replacing ECM (1996 and earlier models ONLY) 2) Calibrating the ECM 3) Replacing stock air cleaner with air cleaner from kit. 1) REPLACING ECM (1996 and earlier models ONLY) 1. Refer to the REMOVAL/REPLACEMENT section 9C in the 1995-1996 FLT Service Manual, Part No. 99483- 96A. 2. Install ECM in accordance with the installation procedure given in the Service Manual. 2) CALIBRATING THE ECM Have dealer recalibrate the ECM prior to starting vehicle. NOTE The product information (EO) label contained in this kit is required in the state of California only. This label is required to aid in passing the California Smog Check Program. Place the information label on the right side of the frame directly beneath the VIN sticker. Do not place the label over other product information labels. Do not place the label on motorcycles other than those specified in the instruction sheet. 3) REPLACING STOCK AIR CLEANER Removing Stock Air Cleaner NOTE Refer to the applicable Service Manual and check the warm- slow idle speed adjustment before removing stock backplate. 1. Remove stock backplate following the instructions given in the appropriate Service Manual. 2. See Service Parts Illustration. Retain stock air cleaner cover and buttonhead screw and washer. Installing High Performance Air Cleaner 1. See Service Parts Illustration. Locate banjo bolts (10) included with kit. Place one washer (11) over each banjo bolt. Insert bolts through holes in mounting bracket (15). Place a second washer over each bolt. Place manifold breather (16) over bolts with hose fitting toward rear of motorcycle. Install remaining washers over the ends of bolts

HARLEY DAVIDSON CHROME HANDLEBAR CLAMP BOLT KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 02-02-2011

download
INSTALLATION Improperly aligned handlebars can contact the fuel tank when turned to the left or right. Contact with the fuel tank can cause cosmetic damage. (00372a) NOTES Check that the handlebar is centered on the risers. To make sure that the handlebar is centered, verify that the knurled areas on the outboard side of each riser are equal. Slowly turn the front wheel to the full right fork stop and then the full left fork stop to be sure the handlebar does not contact the fuel tank. If contact with the fuel tank occurs or the handlebars are not properly centered, see Figure 1. Slightly loosen the four upper clamp screws, and center the handlebar or raise the handlebar angle as necessary until proper clearance is obtained, then temporarily snug the screws, but do not fully tighten. 4 1 2 3 4 is00868 1. Upper clamp 2. Screw (4) 3. Handlebar 4. Handlebar risers (2) Figure 1. Handlebar Clamp Hardware 1. Remove and discard screws (2) that fasten upper clamps (1) to handlebar risers (4). Save washers under screw head for later use. 2. For Kit 94453-04: Select new chrome screws from the kit that match the length of the screws removed. For all other Kits: Select new chrome screws from the kit. 3. Slide washers previously removed onto screws, and thread screws through the upper clamps into risers. -J03586 1 of 2 4. If handlebar adjustments were made, snug screws but do not fully tighten. a. The bottom surfaces of upper clamps are offset, creating a gap between the clamp and riser on one side. b. Tighten clamps so the gaps appear to the rear of the handlebar, then tighten screw to 12-15 ft-lbs (16.3- 20.3 Nm). 5. If handlebar adjustments were not made, tighten screws to 12-15 ft-lbs (16.3-20.3 Nm). SERVICE PARTS

2007 YAMAHA ZX6RR GALFER Super Bike BRAKE LINES INSTALLATION INSTRUCTIONS

0

Filed Under (Yamaha) by admin on 29-01-2011

download
Step 1: Identify the key components that complete our Super bike KIT, you should have 1 complete 3 line kit (front Kit), 1 single banjo bolt and 2 lower male adapters. There are also a total of 6 washers, 4 will be used, and 2 are spares. The Left hose has a locating clip and there is a new bolt to bolt that on. We ALWAYS strongly suggest having a professional mechanic install these brake lines, all other installations VOID warranty. Inspect your brake system after every race. A: Right Caliper B: Please re-use stock routing clip for right line Step 2: Cover the complete front end of the bike so that if any brake fluid does spill the paint will not be damaged, brake fluid will spill, there is no question!! Step 3: Uninstall stock hoses; be aware of how the stock system was routed in case you need to re-install it. Step 4: Install onto the calipers the Galfer male adapters, the course thread area threads to the caliper with one washer. Torque level is 12 to 13 ft pounds. See Picture C

2006-2008 Yamaha R6 FK002D512GP ( GP Kit ) INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 29-01-2011

download
Step 1: Identify the key components that complete our GP kit: You should have 3-line (front kit), 3 SINGLE banjo bolt and 1 C-CLIP. There are also a total of 8 washers. 6 will be used, and 2 are spares. We strongly suggest having a professional mechanic install these brake lines, all other installations VOID warranty. Inspect your brake system after every race. Step 2: Cover the complete front end of the bike so that if any brake fluid does spill the paint will not be damaged, brake fluid will spill, there is no question!! Step 3: Uninstall stock hoses; be aware of how the stock system was routed in case you need to re-install it. Step 4: Install the GALFER GP 3-Line starting with the master cylinder line (top line). Torque level is 12 to 13 ft pounds. (See picture A2) Step 5: Install the C-CLIP provided to the lower triple tee top line needs to be held by c-clip [see picture A4&A5] . Lower lines will travel in front of the forks to the calipers; two single banjo bolt (see picture A1) are included for master cylinder to each caliper. The positioning sequence on the master cylinder is as follows: Master cylinder, washer, forty-degree banjo (Top line), and washer. Single banjo bolt torque level is 12 FT Pounds. ( See picture A2 for positioning) Make sure that the [ CALIPER fittings ] on each caliper are positioned [ positioning ] (see picture A6- A7) . Thread banjo bolt into the caliper, and torque bolt to 12 to 13 Ft pounds. Before you proceed to the next step, please check for clearance of the lines. Compress the front end to make sure that the lines are not binding with anything. When the front end is fully extended or fully compressed, double check that the lines are traveling correctly and are clear of any obstructions. Once the lines have been checked for clearance. Proceed to step #6 Step 6: Bleed brake system according to owner’s manual, and build appropriate pressure. Finishing with GALFER DOT 4-brake fluid is recommended.

HARLEY DAVIDSON LED FUEL GAUGE KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
Removing the Analog Fuel Gauge NOTE The fuel gauge wires are routed through a tube in the fuel tank, and are secured by a clip at the bottom of the tank and, on some models, a clamp on the frame. Open the clip and clamp as needed, and be sure there is enough slack in the wires to be able to lift out the gauge. 1. At the bottom left side of the fuel tank, bend back the flexible clip slightly to free the fuel gauge conduit. Open the harness clamp on the frame if necessary to free the conduit. Gently pull on the conduit to draw the Multilock connector [117] out of the tunnel. 2. See Figure 2. Depress the pin on the socket terminal side of the connector, and pull apart the pin and socket halves. 3. See Appendix B in an appropriate Service Manual. Use a pick (Snap-On TT600-3 or equivalent) to remove the terminals or clip off the wires. Remove and discard the fuel gauge. 4. For Carbureted Models: See Figure 2. Remove the fuel gauge by firmly grasping and carefully pulling up (do NOT twist) on the gauge just far enough to free it from the fuel tank. Disconnect the two sending unit connectors. Feed the conduit and two wires up through the tube while removing the gauge. Remove and discard the fuel gauge. For Fuel-Injected Models: See Figure 2. Remove the fuel gauge by firmly grasping and carefully pulling up (do NOT twist) on the gauge to free it from the fuel tank. Feed the conduit and three wires up through the tube while removing the gauge. Remove and discard the fuel gauge. 5. Remove and discard the rubber gasket. INSTALLATION For Kit Numbers 75084-04B or 75237-03B 1. See Figure 2. Assemble the new gasket (3) to the LED fuel gauge (1) from the kit. Install the gasket so the flat side contacts the edge of the gauge. 2. See Figure 1. Use three of the Phillips-head screws and washers from the kit to connect the wires as follows: Fasten the Orange wire (1) ring terminal to the gauge connection marked “12V and “O” with a screw and washer. Fasten the Black wire (2) ring terminal to the connection marked “GND” and “BK” with a screw and washer. Fasten the Yellow/White wire (3) ring terminal to the connection marked “Y/W” with a screw and washer. 3. See Figure 2. While carefully lowering the fuel gauge, feed the wire harness (2) down into the drain tube until the three short (Orange, Black, Yellow/White) wires exit the hole at the bottom of the fuel tank. Gently pull the wires to remove slack while installing the gauge to the fuel tank. Do not twist the gauge during installation. Hold the gauge firmly and press down until it snaps into place

Incoming search terms:

2003-2004 Honda CBR600RR FK003D348SB Superbike Kit INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 25-01-2011

download
Step 1: Identify the key components that complete our Superbike kit: You should have 2 lines (front kit), 1 double banjo bolt and 2 lower adapters. There are also a total of 7 washers. 5 will be used, and 2 are spares. We strongly suggest having a professional mechanic install these brake lines; all other installations VOID warranty. Inspect your brake system after every race. Step 2: To ensure no paint damage from a brake fluid spill, completely cover the front end of the bike. This process is messy, and brake fluid WILL drip! Step 3: Uninstall stock hoses; be aware of how the stock system was routed in case you need to re-install it. Step 4: Install the Galfer adapters onto the right and left calipers. Thread each adapter into the calipers with one washer, and torque at 12 to 13 ft pounds. (See picture S1) Step 5: Install the right and left lines to the calipers, using the shorter line on the right side. These lines will travel from the master cylinder to the calipers; a double banjo bolt (see picture S2) is included to run two lines down. The positioning sequence on the master cylinder is as follows: Master cylinder, washer, 12-degree banjo (from right line), washer, 12-degree banjo (from left line), washer, and double banjo hex. Double banjo bolt torque level is 12 FT Pounds. (See picture S3) Make sure that the 40-degree fittings on each caliper are pointing away from the bike just a little bit (see picture S4/S5 for right caliper and S6/S7 for left) . Thread each banjo end into the adapter, and torque to 6 ½ Ft pounds. Before you proceed to the next step, please check for clearance of the lines. Compress the front end to make sure that the lines are not binding with anything. When the front end is fully extended or fully compressed, double check that the lines are traveling correctly and clear from any obstructions. Once the lines have been checked for clearance, we recommend using a zip-tie to bring the lines together about an inch above the lower triple clamp area

1994-2003 Suzuki GSXR750 and 1997-2004 Suzuki GSXR600 Superbike Kit INSTALLATION INSTRUCTIONS

0

Filed Under (Suzuki) by admin on 10-01-2011

download
Step 1: Identify the key components that complete our Superbike kit: You should have 2 lines (front kit), 1 double banjo bolt and 2 lower adapters. There are also a total of 7 washers. 5 will be used, and 2 are spares. We strongly suggest having a professional mechanic install these brake lines; all other installations VOID warranty. Inspect your brake system after every race. Step 2: To ensure no paint damage from a brake fluid spill, completely cover the front end of the bike. This process is messy, and brake fluid WILL drip! Step 3: Uninstall stock hoses; be aware of how the stock system was routed in case you need to re-install it. Step 4: Install the Galfer adapters onto the right and left calipers. Thread each adapter into the calipers with one washer, and torque at 12 to 13 ft pounds. (See picture S4) Step 5: Install the right and left lines to the calipers, using the shorter line on the right side. These lines will travel from the master cylinder to the calipers; a double banjo bolt (see picture S5) is included to run two lines down. The positioning sequence on the master cylinder is as follows: Master cylinder, washer, straight banjo (from right line), washer, 12-degree banjo (from left line), washer, and double banjo hex. Double banjo bolt torque level is 12 FT Pounds. ( See picture S6) Make sure that the 90-degree fittings on each caliper are pointing away from the bike just a little bit (see pictures S7 through S9 of calipers) . Thread each banjo end into the adapter, and torque to 6 ½ Ft pounds. Before you proceed to the next step, please check for clearance of the lines. Compress the front end to make sure that the lines are not binding with anything. When the front end is fully extended or fully compressed, double check that the lines are traveling correctly and clear from any obstructions. Once the lines have been checked for clearance, we recommend using a zip-tie to bring the lines together about an inch above the lower triple clamp area. (Picture S10) Step 6: Bleed brake system according to owner’s manual, and build appropriate pressure. Finishing with DOT 4-brake fluid is recommended.

Incoming search terms:

2007-2008 KAWASAKI ZX-6RR GP Kit INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 05-01-2011

download
Step 1: Identify the key components that complete our GP kit: You should have 3-line (front kit) , 3 SINGLE banjo bolt and 1 C-CLIP. There are also a total of 8 washers. 6 will be used, and 2 are spares. We strongly suggest having a professional mechanic install these brake lines, all other installations will VOID the warranty . Inspect your brake system after every race. Step 2: Cover the complete front end of the bike so that if any brake fluid does spill the paint will not be damaged, brake fluid will spill, there is no question!! Step 3: Uninstall stock hoses; be aware of how the stock system was routed in case you need to re-install it. Step 4: Install the GALFER GP 3-Line starting with the master cylinder line (top line). Torque level is 12 to 13 ft pounds. (See picture A2) Step 5: Install the C-CLIP provided to the lower triple tee left line needs to be held by c-clip [see picture A4] . Lower lines will travel in front of the forks to the calipers; three single banjo bolt (see picture A1) are included for master cylinder to each caliper. The positioning sequence on the master cylinder is as follows: Master cylinder, washer, 40-degree banjo (Top line), and washer. Single banjo bolt torque level is 12 FT Pounds. ( See picture A2 for positioning) Make sure that the [ CALIPER fittings ] on each caliper are positioned [ positioning ] (see picture A5- A6) . Thread banjo bolt into the caliper, and torque bolt to 12 to 13 Ft pounds. Before you proceed to the next step, please check for clearance of the lines. Compress the front end to make sure that the lines are not binding with anything. When the front end is fully extended or fully compressed, double check that the lines are traveling correctly and are clear of any obstructions. Once the lines have been checked for clearance.