Yamaha 1998 XVS1100 REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 03-01-2012

download
EXPLODED DIAGRAMS To help identify parts and clarify procedure steps, there are exploded diagrams at the start of each removal and disassembly section. 1. An easy-to-see exploded diagram 4 is provided for removal and disassembly jobs. 2. Numbers 5 are given in the order of the jobs in the exploded diagram. A number that is enclosed by a circle indicates a disassembly step. 3. An explanation of jobs and notes is presented in an easy-to-read way by the use of symbol marks 6 . The meanings of the symbol marks are given on the next page. 4. A job instruction chart 7 accompanies the exploded diagram, providing the order of jobs, names of parts, notes in jobs, etc. 5. For jobs requiring more information, the step-by-step format supplements 8 are given in addition to the exploded diagram and the job instruction chart.
24 21 18 15 16 17 10 12 13 11 14 1 3 5 7 9 2 4 8 6 19 20 22 23 25 EB003000 ILLUSTRATED SYMBOLS Illustrated symbols 1 to 9 are printed on the top right of each page and indicate the subject of each chapter. 1 General information 2 Specifications 3 Periodic inspections and adjustments 4 Engine 5 Cooling system 6 Carburetion 7 Chassis 8 Electrical 9 Troubleshooting Illustrated symbols 10 to 17 are used to identify the specifications appearing in the text. 10 Can be serviced with engine mounted 11 Filling fluid 12 Lubricant 13 Special tool 14 Torque 15 Wear limit, clearance 16 Engine speed 17 Ω, V, A Illustrated symbols 18 to 23 in the exploded diagrams indicate the types of lubricants and lubrication points. 18 Apply engine oil 19 Apply gear oil 20 Apply molybdenum disulfide oil 21 Apply wheel bearing grease 22 Apply lightweight lithium-soap base grease 23 Apply molybdenum disulfide grease Illustrated symbols 24 to 25 in the exploded diagrams indicate where to apply locking agent 24 and when to install new parts 25. 24 Apply locking agent (LOCTITE) 25 Replace

Incoming search terms:

Honda 400EX Hub installation instructions

0

Filed Under (Honda) by admin on 20-12-2011

download
Remove all contents from its packaging and verify that all parts are present and free from damage. You should have the following items: (2) wheel hubs (2) smaller tapered bearings (2) large tapered bearings (2) wheel bearing nuts (2) dust caps (2) inner bearing seals (6) M3 x .5 screws (2) cotter pins (2) inner bearing spacers 2. Completely remove the old hubs from your quad and clean the spindle and the surrounding areas. It is very important to keep the new bearings and seals clean during installation for long life. Be sure to remove the factory inner bearing spacers from the spindle and discard. They will not be used in re-assembly. 3. Pack your new Timken tapered wheel bearings with a liberal amount of high quality wheel bearing grease. A wheel bearing packer works best, however you can accomplish the task by placing the grease in the palm of your hand and manually working it in between the bearing rollers. We also recommend that you pack the area between the bearing races in the hub with grease for additional lubrication and protection against moisture. 4. Place the large wheel bearing (inner) into the hub and install the inner seal. The seal should bottom out against the step in the bore and the face should be flush with the hub. 5. Remove the brake rotors from your old hubs. Re-install the rotors on your new hubs and be sure to use medium strength Loctite on the threads. 6. Apply a light film of grease or oil to the large diameter of the spindle stud. Install the new o-ringed bearing spacer onto the spindle. 7. Apply a thin film of grease to the seal surface on the bearing spacer and the inside diameter of the seal to prevent the seal from running dry. Install the hub onto the spindle and slide the outer bearing over the spindle and install the new bearing nut furnished with your hubs. Do not use the factory nut or washer. 8. SETTING THE BEARING PRELOAD: It is first necessary to seat the bearing before setting the preload. This aligns the rollers and prevents the bearings from loosening after a short period of use. To seat the bearing, tighten the spindle nut while you rotate the hub until the hub becomes difficult to spin. With the bearing now seated, you must set the bearing preload. Preload means placing a small amount of force against the bearings to remove any clearance between the bearing race and the rollers. This is done by backing the nut off completely and re-tightening it with your fingers. Do not rotate the hub while setting the preload . If a hole in the spindle is not accessible for installation of the cotter pin, adjust the nut tighter to bring a hole into alignment. Install the cotter pin and bend the pin around the outside of the nut. Do not attempt to bend the pin toward you (over the end of the spindle) or it may rub on the inside of the dust cap.

Incoming search terms:

DUCATI CLUTCH INSTALLATION INSTRUCTIONS

0

Filed Under (Ducati) by admin on 25-10-2010

download
When a vehicle is so equipped, the pilot must be replaced. The pilot is located in either the engine’s crankshaft or in the center of the flywheel. To remove a flywheel-fit pilot, remove the flywheel from the engine and drive or press out the pilot from the backside of the flywheel. Press or gently tap new pilot into flywheel after flywheel has been machined (where applicable). For crankshaft-fit pilots, an effective means for removal is to select a drift punch or wooden dowel that fits snugly into the old pilot. Then, pack the old pilot tightly with grease. Using the drift punch (or dowel) and a hammer, drive the grease toward the engine. The grease will not compress and will in turn push the old pilot out of the crankshaft. Install the new pilot carefully using a bearing driver. NOTE: Do not grease new pilots. New pilot bearings come pre-greased (often with special synthetic grease). Bronze pilot bushings have oil in the pores of the material that grease will clog. For bushings, a few drops of 30W oil can be used if desired. PRESSURE PLATE AND DISC Install flywheel (refer to flywheel section above) . Always tighten flywheel to crankshaft bolts in a star pattern to manufacturer’s torque specification. Before installing the disc, make sure that it slides smoothly on the transmission input shaft. Apply a thin coat of high temperature grease (such as wheel bearing grease) to the splines of the input shaft. DO NOT USE ANTI-SEIZE! It does not cling to rotating parts. Slide the disc back and forth on the input shaft and remove any extra grease that squishes out of the splines of the disc. Do not get grease or oil on the disc facing. Any grease or oil on a disc facing can be removed with alcohol or brake cleaner if done quickly. Lay the disc on the flywheel noting the flywheel side of the disc and hold it in place with the alignment tool. Clean the pressure ring of the pressure plate with brake cleaner to remove the rust inhibiting coating. Do not spray the entire pressure plate with brake cleaner as lube for internal parts will be removed. Set the pressure plate on the flywheel dowel pins (if equipped) and hand tighten the hold-down bolts. With hand tools, tighten pressure plate bolts ½ turn at a time in a star pattern until the manufacturer’s torque specification is met. Remove the alignment tool. NOTE: Different brands of the same pressure plate may have a difference in appearance and uninstalled lever height. These are not issues. Appearance can vary greatly and the installed lever height will be the same.

Incoming search terms:

Incoming search terms: