2003 – 2006 KTM The e-Axle Installation Manuals

0

Filed Under (KTM) by admin on 01-02-2012

download
Remove the stock wheel spacers from both sides of the wheel hub and install both of the Rekluse wheel spacers. After installing the Rekluse wheel spacers, stow the wheel in a suitable place so that the brake rotor cannot be damaged. See following picture. 5 5. Remove the brake pads by removing the clips and sliding out the pin. See following picture. 6. Remove the leaf spring from the caliper. See following picture. 7. Re-install the brake pads with the included coil spring positioned on the pin between the brake pads. Secure the pin by re-installing the 2 clips. See following picture. Coil Spring on the pin and in between the brake pads 6 8. Coat the center axle in a thin layer of grease to aid in sliding the center axle on and off. Note: Coat the center axle in a thin layer every time it is reinstalled after removing the front wheel for tire maintenance. 9. Position the front wheel back in between the forks so that the brake disk is in place between the brake pads, and so the wheel spacers line up with the hole in the fork fists. 10. Slide the center axle, with 30-mm Bushing attached, through the right-side fork fist and through the wheel spacers in the front hub. Rotate the 30-mm bushing so the set screw is facing up, this will line the “0″ Offset Mark with the fork fist pinch clamp slot. Continue sliding the axle through until the 30-mm bushing is almost flush with the outer edge of the right fork fist. See following picture

Honda 300 2×4 Lift Kit Installation Instructions

0

Filed Under (Honda) by admin on 11-12-2011

download
This product is designed for us e on ATVs on which additional ground clearance and fender clearance is desired. It is designed for utility type, slower-speed use on relatively flat terrain in deep mud or snow. Although we have many thousands of satisfied lift kit customers and over 400 franchised dealers selling and installing lift kits, purchasers should be aware that use of this product may increase the frequency of required maintenance, part wear, and will raise the center of gravity on your ATV increasing risk of roll-over on side hills, ditches or other steep terrain. We recommend that wider tires and/or wheel spacers be used to achieve a wider stance and to improve stability of the ATV. Riders should be advised that the handling characteristics of a taller ATV are different and require extra care when riding on side hills or off-camber situations. If you further raise the center of gravity by adding heavy loads to racks or seats, the ATV must be operated with care, at slower speeds or on relatively flat ground. Operation of an ATV with or without a lift kit, while or shortly after consuming alcohol or drugs, subjects the rider to the risk of serious bodily harm or possible death. This is compounded if the rider does not wear an approved helmet and other safety gear. High Lifter urges that all approved safety gear be worn when riding an ATV. If this is not what you expected, or is not consistent with your intended use, you should return the product immediately to the seller, before installation, for a refund of the purchase price; less any fees. After installation, product is warranted for 90 days for defects in workmanship and materials. Warranty is limited to refund of the purchase price or replacement of the kit, at the seller’s option.

HARLEY DAVIDSON FRONT NINE-SPOKE WHEELS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-04-2011

download
INSTALLATION 1. Remove existing front wheel assembly. Save axle, axle nut, brake disc, and wheel spacers for kit installation. Refer to FRONT WHEEL in service manual. For FLSTC and FLSTN models: Discard moon-style hub cap. Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. (00319b) 2. See Figure 1. Install valve stem assembly (D) on wheel. Refer to TIRES in service manual. 3. Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate service parts table. Refer to FRONT WHEEL in service manual. NOTES Install the primary bearing first with the WHEEL BEARING REMOVER/INSTALLER, following the service manual instructions. The machined grooves in the hub face indicate the primary bearing side. The front wheel should be installed so that the valve stem is on the right side of the motorcycle. 4. Install wheel assembly parts from the appropriate service parts table for your fitment and stock brake disc(s). Discard parts from the installation kit that are not required. Refer to FRONT WHEEL in service manual. 5. For FLSTC and FLSTN Models: Install wheel kit and right side wheel spacer provided in kit installation. All other models: Install wheel spacers previously removed. 6. Install front wheel (1), stock axle and stock axle nut. Refer to FRONT WHEEL in service manual. 7. For 2009-Later TLE/U Sidecars: Assemble the sidecar brake disc and hub cap (purchased separately) to the wheel. The brake disc is to be installed on the side of the wheel opposite the valve stem. Install wheel according to the sidecar service manual

HARLEY DAVIDSON 80-SPOKE REAR WHEEL KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 31-03-2011

download
Additional Parts Required This kit includes the custom wheel only. Proper installation of this kit requires the separate purchase of the following parts which are available at a Harley-Davidson dealer: •Wheel Bearing Remover and Installer (HD-44060) •Wheel Installation Kit (See Service Parts Tables for part number) The following Harley-Davidson Genuine Motor Accessories are recommended for proper maintenance and cleaning: •Harley® Bright™ Chrome Cleaner (94683-99) •Harley® Glaze™ Polish and Sealant (99701-84) •Harley®Wheel and Spoke Brush (43078-99) •Harley-Davidson®Wheel and Tire Cleaner (94658-98) The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Kit Contents See the Service Parts section for kit contents. INSTALLATION 1. Remove existing rear wheel assembly. Save axle, axle nut, brake disc and wheel spacers for kit installation. NOTE Remove the rear brake caliper before removing the wheel. Do not re-use sprocket mounting screws. Re-using sprocket mounting screws can result in torque loss and damage to the sprocket and/or belt assembly. (00480b) 2. Install the tube and tire on wheel. Refer to REAR WHEEL in the Service manual. Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. (00319b) NOTES Install the primary bearing first using appropriate Service Manual and WHEEL BEARING REMOVER/INSTALLER. 3. Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate service parts table. Refer to REAR WHEEL in Service Manual. 4. Install rear wheel (1), stock axle and stock axle nut. Refer to REAR WHEEL in Service Manual

Incoming search terms:

HARLEY DAVIDSON BLADE FRONT WHEEL KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-03-2011

download
INSTALLATION 1. Remove existing front wheel assembly. Save axle, axle nut, brake disc, and wheel spacers for kit installation. Refer to FRONT WHEEL in service manual. For FLSTC and FLSTN Models: Discard moon-style hub cap. or FXSTD: Discard tapered spacer. NOTE Install short valve stem (43157-83A) included in the installation kit. Discard all other valve stems. 2. See Figure 2. Install valve stem assembly (L) on wheel. Refer to TIRES in service manual. Do not re-use brake disc/rotor screws. Re-using these screws can result in torque loss and damage to brake components. (00319c) NOTES Install the primary bearing first using appropriate service manual and WHEEL BEARING REMOVER/INSTALLER. The side with the machined groove on the hub face is the primary bearing side for all kits except Kits 41681-07 and 40818-08. For Kit 41681-07: Install the wheel so that the hub markings are on the left side and the machined groove is on the right side of the motorcycle. • For 2006 and later FXDWG Models: When correctly installed, the tire will be 0.08-0.2 in (2-5 mm) off of center, compared to the fender. • For 2007 and later FX Softail and 2008 and later FXDWG Models: The left side of the wheel is the primary bearing side. • For 2006 and earlier FX Softail and 2007 and earlier FXDWG Models: The right side of the wheel is the primary bearing side. For Kit 40818-08: • Proper installation of this kit requires the separate purchase of two floating brake discs (44343-01 for 2004 – 2007 models and 44553-06A (stock) or 41500012 (polished) for 2008 and later models) and a tire (43371-07 on 2004-2008 models and 44026-09A on 2009-later models). The left side of the wheel has machined DOT markings to identify it as the primary bearing side. • For 2008 and later Touring: Install bearing shim (43903- 08) under the primary bearing. 3. Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate service parts table. Refer to FRONT WHEEL in service manual. 4. For FLSTC and FLSTN Models: Install wheel kit and right hand wheel spacer provided in installation kit. Refer to FRONT WHEEL in service manual. For FXSTD Models: Install wheel kit, stock wheel spacer and right side wheel spacer provided in installation kit in place of the tapered spacer discarded in Step 1. Refer to FRONT WHEEL in service manual. For FXSTS Models: Install wheel kit, stock wheel spacers and spacer provided in installation kit between the left side wheel spacer and the left fork. For all other models: Install previously removed wheel spacers. Refer to FRONT WHEEL in service manual. 5. Install front wheel (1), stock axle and stock axle nut. Refer to FRONT WHEEL in service manual. MAINTENANCE AND CLEANING Chrome parts must be maintained regularly to verify that they keep their original shine and luster. 1. Clean heavily-soiled wheel surfaces using Harley-Davidson Wheel and Tire Cleaner, applied with Harley Wheel and Spoke Brush. 2. Thoroughly clean chrome with a good quality chrome cleaner, such as Harley Bright Chrome Cleaner. 3. After cleaning and polishing, seal the finish with a good quality sealer, such as Harley Glaze Polish and Sealant

Incoming search terms:

HARLEY DAVIDSON REAR SLOTTED SIX-SPOKE WHEELS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-03-2011

download
INSTALLATION 1. Remove existing rear wheel assembly. Save axle, axle nut, brake disc, and wheel spacers for kit installation. Refer to REAR WHEEL in Service Manual. NOTES Prior to removing or installing the wheel, the rear brake caliper must be removed. The cotter pin or spring clip for the axle nut must be replaced. They are available for purchase from your dealer. See your dealer for the correct part number for your model motorcycle. NOTE Install long valve stem (43206-01) included in the installation kit. Discard all other valve stems. 2. See Figure 1. Install valve stem assembly (I) on wheel. Refer to TIRES in service manual. Do not re-use brake disc/rotor screws. Re-using these screws can result in torque loss and damage to brake components. (00319c) Do not re-use sprocket mounting screws. Re-using sprocket mounting screws can result in torque loss and damage to the sprocket and/or belt assembly. (00480b) NOTE For Kits 43928-08 and 43929-08: When installing wheel on 2008 and later XL models, install bearing shim from installation kit under the primary bearing. For Kits 43934-07, 43942-07 and 43972-07: When installing wheel on 2008 and later Dyna models, install bearing shim from installation kit under the primary bearing. 3. Assemble wheel installation kit components, stock brake disc, and sprocket to wheel using the appropriate service parts table. Refer to REAR WHEEL in Service Manual. NOTES The valve stem side of the wheel and machined grooves in the hub face indicate the primary bearing side. Install the primary bearing first using appropriate service manual and WHEEL BEARING REMOVER/INSTALLER. 4. Install rear wheel (1), stock axle, and stock spacers to motorcycle. Refer to REAR WHEEL in service manual. MAINTENANCE AND CLEANING Chrome parts must be maintained regularly to keep their original shine and luster. 1. Clean heavily-soiled wheel surfaces using Harley-Davidson Wheel and Tire Cleaner, applied with Harley Wheel and Spoke Brush. 2. Thoroughly clean chrome with a good quality chrome cleaner, such as Harley Bright Chrome Cleaner. 3. After cleaning and polishing, seal the finish with a good quality sealer, such as Harley Glaze Polish and Sealant

HARLEY DAVIDSON REAR ROAD WINDER WHEELS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-03-2011

download
This instruction sheet references service manual information. A service manual for your model motorcycle is required for this installation and is available from a Harley-Davidson dealer. Kit Contents See Figure 1 and Service Parts Tables. INSTALLATION 1. Remove existing rear wheel assembly. Save axle, axle nut, brake disc and wheel spacers for kit installation. Refer to the service manual. NOTES Prior to removing or installing the wheel, the rear brake caliper must be removed. The cotter pin or spring clip for the axle nut must be replaced. They are available for purchase from you dealer. See your dealer for the correct part number for your model motorcycle. Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. (00319b) Do not re-use sprocket mounting screws. Re-using sprocket mounting screws can result in torque loss and damage to the sprocket and/or belt assembly. (00480b) 2. See Figure 1. Install valve stem assembly (E) on wheel. Refer to the service manual. 3. Assemble wheel installation kit components, stock brake disc, and sprocket to wheel using the appropriate service parts table. Refer to the service manual. NOTES Install the primary bearing first using appropriate service manual and WHEEL BEARING REMOVER/INSTALLER. The machined grooves in the hub face indicate the primary bearing side. 4. Install rear wheel (1), stock axle and stock spacers to motorcycle. Refer to the service manual. MAINTENANCE AND CLEANING Chrome parts must be maintained regularly to keep their original shine and luster. 1. Clean heavily-soiled wheel surfaces using Harley-Davidson Wheel and Tire Cleaner, applied with Harley Wheel and Spoke Brush. 2. Thoroughly clean chrome with a good quality chrome cleaner, such as Harley Bright Chrome Cleaner. 3. After cleaning and polishing, seal the finish with a good quality sealer, such as Harley Glaze Polish and Sealant

Incoming search terms:

HARLEY DAVIDSON FRONT DETONATOR WHEELS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-03-2011

download
INSTALLATION 1. Remove existing front wheel assembly. Save axle, axle nut, brake disc and wheel spacers for kit installation. Discard moon-style hub cap on FLSTC and FLSTN models. Discard left side spacer on FXSTS models and tapered spacer on FXSTD models. Refer to FRONT WHEEL in Service Manual. Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. (00319b) 2. See Figure 1. Install valve stem assembly (D) on wheel. Refer to TIRES in Service Manual. 3. Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate service parts table. Refer to FRONT WHEEL in Service Manual. NOTE Install primary bearing first using the applicable Service Manual and WHEEL BEARING REMOVER/INSTALLER. Kit 44550-07: The left side of the wheel has a groove machined in the hub to identify it as the disc side for installation, as well as the primary bearing side. The wheel should be installed so that the valve stem is on the right side of the motorcycle. Kits 44660-07 and 44661-07: The wheel should be installed so that the hub markings are on the left side of the motorcycle. An arrow engraved into the rim of 44661-07 indicates the direction of rotation. A groove is machined in the left-side hub face to indicate the primary bearing side. • Dual-disc models: Install the brake discs according to the Service Manual procedures. The Chrome hub cap (2) is not used. • Single-disc models: Install the brake disc according to the Service Manual procedures. Install the chrome hub cap (2) on the side opposite the brake disc. Kit 44660-07: The gross axle weight rating is unaffected by the installation of this wheel on a vehicle originally equipped with 21-inch wheels. Kit 44661-07: The gross axle weight rating is unaffected by the installation of this wheel on a vehicle originally equipped with 19-inch wheels. Kit 44552-08: The left side of the wheel has a groove machined in the hub to identify it as the left side for installation, as well as the primary bearing side. The wheel should be installed so that the valve stem is on the right side of the motorcycle. Kit 44556-07: The right side of the wheel has a groove machined in the hub to identify it as the right side for installa

HARLEY DAVIDSON FRONT AGITATOR WHEELS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 06-03-2011

download
Recommended Additional Parts The following Harley-Davidson Genuine Motor Accessories are recommended for proper maintenance and cleaning: •Harley® Bright™ Chrome Cleaner (94683-99) •Harley® Glaze™ Polish and Sealant (99701-84) •Harley®Wheel and Spoke Brush (43078-99) •Harley-Davidson®Wheel and Tire Cleaner (94658-98) Kit Contents See Figure 1 and the Service Parts Tables. INSTALLATION 1. Remove existing front wheel assembly. Save axle, axle nut, brake disc and wheel spacers for kit installation. See the service manual. Do not re-use brake disc/rotor screws. Re-using these screws can result in torque loss and damage to brake components. (00319c) 2. See Figure 1. Install valve stem assembly (D) on wheel. See the service manual. 3. Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate service parts table. See the service manual. 4. Install primary bearing with a Wheel Bearing Remover and Installer. See the service manual. The left side of the wheel has DOT cast in the wheel to indicate the primary side of the wheel. 5. Install wheel spacers (previously removed). 6. Install front wheel (1) and stock axle. See the service manual. MAINTENANCE AND CLEANING Chrome parts must be maintained regularly so they keep their original shine and luster. 1. Clean heavily-soiled wheel surfaces using Harley-Davidson Wheel and Tire Cleaner, applied with Harley Wheel and Spoke Brush. 2. Thoroughly clean chrome with a good quality chrome cleaner, such as Harley Bright Chrome Cleaner. 3. After cleaning and polishing, seal the finish with a good quality sealer, such as Harley Glaze Polish and Sealant

HARLEY DAVIDSON REAR DEUCE WHEELS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 25-02-2011

download
INSTALLATION 1. Remove existing rear wheel assembly. Save axle, axle nut, brake disc and wheel spacers for kit installation. Refer to REAR WHEEL in Service Manual. NOTES Prior to removing or installing the wheel, the rear brake caliper must be removed. The cotter pin or spring clip for the axle nut must be replaced. They are available for purchase from your dealer. See your dealer for the correct part number for your model motorcycle. Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. (00319b) Do not re-use sprocket mounting screws. Re-using sprocket mounting screws can result in torque loss and damage to the sprocket and/or belt assembly. (00480b) 2. See Figure 1. Install valve stem assembly (E) on wheel. Refer to TIRES in Service Manual. 3. Assemble wheel installation kit components, stock brake disc and sprocket to wheel using the appropriate service parts table. Refer to REAR WHEEL in Service Manual. The valve stem side of the wheel is the primary bearing side. NOTES Install the primary bearing first using appropriate Service Manual and WHEEL BEARING REMOVER/INSTALLER. The valve stem side of the wheel is the primary bearing side. 4. Install rear wheel (1), stock axle, and stock spacers to motorcycle. Refer to REAR WHEEL in Service Manual. MAINTENANCE AND CLEANING Chrome parts must be maintained regularly to ensure that they keep their original shine and luster. 1. Clean heavily-soiled wheel surfaces using Harley-Davidson Wheel and Tire Cleaner, applied with Harley Wheel and Spoke Brush. 2. Thoroughly clean chrome with a good quality chrome cleaner, such as Harley Bright Chrome Cleaner. 3. After cleaning and polishing, seal the finish with a good quality sealer, such as Harley Glaze Polish and Sealant