2006 Honda ST1300/ A SET-UP INSTRUCTIONS

0

Filed Under (Honda) by admin on 21-04-2011

download
Remove the carton cover. The ST1300/A is crated in one of two ways. You may receive either one. Covered crate: Cut the strap and remove the carton cover. Remove the inner cardboard frame cover. Uncovered crate: When stacking crates, protect the motorcycle from falling objects and bad weather. 2. Check for damage. Check the unit for hidden damage. If you find damage, follow the instructions on the Delivery and Damage Claims Guidelines wall chart (Reorder No. S0477) before proceeding. 3. Remove the side braces, wheel, loose parts cartons, and crate frame. Remove the ties securing the front wheel and loose parts cartons. 3. Remove the side braces, wheel, loose parts cartons, and crate frame (cont.). Remove the bolts and side braces, being careful not to damage the front wheel. Remove the loose parts cartons. Keep the You and Your Motorcycle Riding Tips & Practice Guide and hand deliver to the customer at the time of delivery. Remove the nuts, plate, and bolts. Using two people, carefully remove the crate frame, being careful not to damage the motorcycle Remove the motorcycle from the crate base. Install lifting slings on the engine guards and grab rails as shown. If necessary, use a spreader board to prevent the slings from damaging the motorcycle. Lift the slings just enough to remove the slack. Loosen the caliper bolts, axle bolt, and axle pinch bolts. Remove the washer bolts, and lower shipping bracket from the crate base. Discard the washer bolts

HARLEY DAVIDSON POLISHED BRAKE ROTOR (DISC) KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 16-04-2011

download
INSTALLATION 1. See the WHEEL section of the Service Manual for brake disc removal and disassembly procedures. 2. See Figure 1. Assemble and install the new brake disc (1) as described in the WHEEL section of the Service Manual using the new screws (2). Tighten the screws for front brake rotor (disc) kits to 16-24 ft-lbs (22-33 Nm). Tighten the screws for rear brake rotor (disc) kit to 30-45 ft-lbs (41- 61 Nm)

HARLEY DAVIDSON TOURING CHROME DEBRIS DEFLECTOR COVER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 22-03-2011

download
This kit is designed for installation on all 1997 and later Touring Model Motorcycles. NOTE The chrome debris deflector cover mounts over the existing deflector. Kit Contents Qty Description 1 Cover, debris deflector, chrome Installation 1. Remove left side saddlebag. 2. Remove the stock debris deflectors two rear screws. Save screws for installation. 3. Slide the debris deflector cover over the stock debris deflector making sure the lower edge of the deflector is inserted into the edge clip of the cover. 4. Install the two screws saved from Step 2. Tighten securely. 5. Make sure that debris deflector cover does not contact the drive belt, tire or wheel. If necessary, loosen the mounting screws and reposition for clearance

HARLEY DAVIDSON FRONT BRAKE DISC LOCK INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-03-2011

download
INSTALLATION Do not operate vehicle with brake disc lock in place. Operation with lock on disc will restrict movement of the wheel, which could result in death or serious injury. (00457b) NOTE Insert key all the way to the bottom of the cylinder. Turn key clockwise 180 degrees to the open position. DO NOT FORCE KEY! Key should turn freely. If key does not freely rotate, try turning key slightly left and right while inserting to align disks inside cylinder. Failure to insert key all the way to the bottom of cylinder could cause key to jam. For Models with Hydraulic Fork Front Ends 1. See Figure 1. Insert reminder cord (3) into slot on disc lock (1). 2 1 3 is 01599 1. Lock 2. Caliper 3. Reminder cord Figure 1. Installing Disc Lock 2. Slide lock (1) over front brake disc as close to rearward edge of brake caliper (2) as possible. Push button completely down to lock. 3. Roll motorcycle forward slowly until lock gently contacts caliper. 4. See Figure 3. After installing disc lock, place loop end (1) of reminder cord (2) over handlebar grip. For Models with Springer Front Ends 1. See Figure 2. Insert reminder cord (5) into slot on disc lock

HARLEY DAVIDSON VRSC CHROME WHEEL KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 18-03-2011

download
Installation To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 1 WARNING 1 WARNING ® Kit Numbers 41279-04, 41282-04, 41463-05, 41467-05, 41633-05, 41634-05, 41640-05, and 41639-05 1 of 3 Figure 1. Rear Wheel Removal i02495 1. Axle (keep) 2. Axle adjuster (keep) 3. Axle nut (keep) 4. “E”-clip (keep) 5. Spacer (3) (keep) 6. Torx screw (5) (replace) 7. Brake disc (keep) 8. Wheel assembly (replace) 9. Valve cap (keep) 10. Compensator bowl (keep) 11. Compensator cushion (keep) 12.12 pt screw (5) (keep) 13. Lockwasher (5) (keep) 14. Sprocket assembly (keep) 1. Refer to the Service Manual and follow the MAXI-FUSE instructions to remove the right-side cover and maxi- fuse. Proceed to Step 2 for the wheel being replaced. Rear Wheel 2. See Figure 1. Remove the rear wheel per the REAR WHEEL, REMOVAL instructions in the Service Manual. 3. Disassemble, clean and inspect all parts to be re-used per Service Manual instructions. 4. Re-assemble all saved components to the new chrome rear wheel assembly. See REAR WHEEL, ASSEMBLY in the Service Manual. Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. (00319b) 5. Fasten the brake disc to the valve stem side of the wheel using the Torx®screws from the kit. Install the compensator bowl with the 12-point screws and lockwashers saved earlier. 6. Install the new wheel to the rear fork. Refer to REAR WHEEL, INSTALLATION in the Service Manual. Proceed to Step 7. Front Wheel 2. See Figure 2. Remove the front wheel per the FRONT WHEEL, REMOVAL instructions in the Service Manual. 3. Disassemble, clean and inspect all parts to be re-used per Service Manual instructions. Mark the left and right brake discs so they can be re-installed to the same location. 4. Re-assemble all saved components to the new chrome front wheel assembly. See FRONT WHEEL, ASSEMBLY in the Service Manual. Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. (00319b) 5. Using the Torx ® shoulder bolts from the kit, and the saved spring washers fasten the brake discs to the same side of the wheel from which they were removed. 6. Install the new wheel to the front forks per the FRONT WHEEL, INSTALLATION instructions in the Service Manual. Proceed to Step 7. Front and Rear Wheels 7. Refer to the Service Manual and follow the MAXI-FUSE instructions to replace the maxi-fuse and right-side cover. After servicing brakes and before moving motorcycle, pump brakes to build brake system pressure. Insufficient pressure can adversely affect brake performance, which could result in death or serious injury. (00279a) After servicing the brake system, test brakes at low speed. If brakes are not operating properly, testing at high speeds can cause loss of control, which could result in death or serious injury. (00289a) Maintenance and Cleaning Chrome parts must be maintained regularly to ensure that they keep their original shine and luster. 1. Clean heavily-soiled wheel surfaces using Harley Wheel and Tire Cleaner, part number 94658-98, applied with Harley Wheel and Spoke Brush, part number 43078-99. 2. Thoroughly clean chrome with a good quality chrome cleaner, such as Harley Bright Chrome Cleaner, part number 94683-99. 3. After cleaning and polishing, seal the finish with a good quality sealer such as Harley Glaze Polish and Sealant, part number 99701-84

Incoming search terms:

HARLEY DAVIDSON DETACHABLE QUARTER FAIRING AND DOCKING HARDWARE KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-03-2011

download
Installation The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley- Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE If your motorcycle has directional lights mounted on the upper fork bracket they must be relocated to the bottom fork bracket. Some models have front directional lights equipped with three wires, the third black wire is a ground wire. Check to determine how many wires are connected to the front directional lights and follow the following procedure that applies. Ifdirectional lights are not mounted on the upper fork bracket proceed to “ASSEMBLING FAIRING”. Relocating Two Wire Directional Lights 1. Support motorcycle on a center stand such that front wheel is raised slightly off the ground. 2. Remove fork tube pinch screw from right side of lower bracket. 3. Cut wires connected to right directional light about 2 in. away from directional light body. 4. Remove fork tube pinch screw from right side of upper fork bracket. (This is the screw that secures the right directional light.) 5. Install right directional light on right side of lower fork bracket using pinch screw removed in step 4. Install pinch screw removed in step 2 into right side of upper bracket. Tighten both pinch screws to 30-35 ft-lbs. 6. Repeat steps 1 through 5 to relocate left directional light. NOTE Fork tubes may slide downward within fork brackets. If this occurs, front fork tube extension above front fork upper bracket will have to be readjusted according to appropriate Service Manual procedures. 7. Connect the right directional light as follows: Strip approx. 5/16 in. of insulation from the wires cut in step 3. 8. Crimp solderless connectors from kit on two wires coming from motorcycle. 9. Split one end of the 2-conductor polarized wire from kit back about 2 in. and strip 5/16 in. of insulation from wire ends. 10. Slide a piece of shrink tubing from kit over each of the wire ends stripped in step 9 and crimp the wires into the terminals installed in step 8. Make sure you connect the silver and copper colored wires to like colored wires. NOTE Polarized wire is used in this application to ensure correct wiring. One wire is silver, one is copper colored. Wire colors of spliced wire must match wire color of original directional wire leads. 11. Cut polarized wires to the length required for connection to the wires at the relocated directional light. Make certain you leave enough slack in wires to allow routing the harness along the fork tube. 12. Split remaining end of the 2-conductor polarized wire from kit back about 2 in. and strip 5/16 in. of insulation from wire ends. 13. Slide heat shrink tubes over the two wire end. 14. Strip 5/16 in. of insulation from wires connected to directional light and connect like colored wires at directional light with connectors from kit. 15. Slide heat shrink tubing over connectors installed in steps 10 and 14. Activate shrink tubing with heat gun or hair dryer.

HARLEY DAVIDSON FRONT FENDER RAILS AND STANCHIONS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 03-03-2011

download
INSTALLATION 1. Carefully cut out appropriate template from sheet included in kit. One side is for FLSTS style fenders (with elliptical hole for front fender lamp), and the other side is for FLT style fenders (with rectangular front fender lamp). 2. Lay template on front fender (align around front fender lamp). 3. Underneath four holes marked on template, place high quality masking tape on fender. 4. Using a tape measure, measure from the top of the striping on the sides of each side of the fender, to the centerline of the each of the holes on the template (on some FLT models, with chrome fender trim, measure from the chrome fender trim at the bottom edge of the fender). Make sure that the distances are equal so that the template is centered on the fender. 5. Tape the template to the fender using high quality masking tape. NOTE Before proceeding, stand directly in front of the fender and carefully check to make sure the template is centered on the fender. 6. Center punch the center point of each of the four holes. 7. Remove the template from the fender. 8. Block motorcycle under frame so the front wheel is raised off the ground. 9. Follow appropriate Service Manual procedures and remove the front axle. 10. Place a rag on the top of the front brake caliper, then lower the front wheel so that it is resting on top of the brake caliper. NOTE When drilling fender holes, use care not to hit tire with drill bit. 11. While holding the fender firmly, and using caution to make sure that your drill bit does not hit the tire, drill the four holes at the points marked by the center punch. Begin with a 1/8 inch drill bit, followed by a 9/32 inch, and finally a 3/8 inch drill bit. 12. Remove the masking tape and any burrs that may have formed. 13. Remove the adhesive backing from each of the foam pads on the bottom of each of the stanchions. 14. Place the studs from each of the end stanchions into the holes (you may need to rotate the rails 180 degrees if they appear to be bowed out). 15. Reaching from the front of the fender, place kit washer, and then a locknut, over each of the studs on the underside of the fender. 16. Securely tighten each locknut so that the stanchion is firmly clamped to the fender. 17. Follow appropriate Service Manual procedures and replace the front wheel and axle

HARLEY DAVIDSON STREET STALKER FRONT FENDER KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 01-03-2011

download
REMOVAL 1. If model has mechanical speedometer drive, remove cable from fender bracket. Disconnect speedometer cable from the speedometer head. 2. Remove front wheel according to the Service Manual. 3. Disconnect and remove fender tip light power wire. 4. Remove hardware that holds fender in place and remove fender. INSTALLATION 1. See Figure 1 and Table 1. For each support bracket (4), remove backing from one side of tape (3), and affix tape to support bracket, carefully matching the contours of the bracket and tape for proper fit. 2. Remove backing from tape and place support brackets into position on the inside of fender (one on each side), aligning the mounting holes in each bracket with the holes in the fender. The tape side will affix to the inside of the fender. 3. Carefully place fender in position and secure fender with screws and flanged locknuts in kit. Tighten hardware to 12 ft-lbs (16.27 Nm). 4. Install front wheel according to the Service Manual. 5. Install mechanical speedometer cable. Use tie wrap (10081) to secure

HONDA GL1500 FRONT WHEEL INSTALLATION MANUAL

0

Filed Under (Honda) by admin on 27-02-2011

download
1. Rotor Covers. Tri-chromed ABS rotor covers replace the painted ones. Light weight, beautiful and functional. Include a rear strap and sold in pairs. Also, available are chrome rotor covers with amber strip lights installed. Fits 1988 to 2000. 2. Fork Light Mounts . Specially designed mounts are tri-chromed metal and hold a total of 6 lights. Lights not included. Sold in pairs 3. LED Lighted Rotor Cover Trim Rings . NEW Update your bike with LED lights. Tri-chromed ABS rings include amber or red, blue and amber LED lights. Sold in Pairs 5. 252-216 Rotor cover Plugs. These¾” chromed steel plugs fill the holes on the GL1500 rotor covers. Sold in a 4 pack

HARLEY DAVIDSON FLSTF TURN SIGNAL RELOCATION KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-02-2011

download
REMOVAL 1. Remove seat according to the instructions in the Service Manual. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 2. See Figure 1. Disconnect battery cables, negative (-) cable first. 2 1 is03242 1. Negative (-) cable 2. Tail lamp connector Figure 1. Negative Battery Cable and Tail Lamp Connector 3. See Figure 2. Remove two screws and tail lamp lens (1) from base (2). 2 1 is03243 1. Tail lamp lens 2. Tail lamp base Figure 2. Remove Tail Lamp Lens 4. See Figure 3. Using a Terminal Pick Tool (1), depress locking tabs and disconnect turn signal connectors (2- place) (2, 3) from circuit board. 5. Feed turn signal wiring and connector through opening in circuit board assembly and into rear wheel area. 6. See Figure 4. Remove turn signal wiring (1, 2) from clips (3) under rear of fender INSTALLATION NOTE Proper installation of kit requires that tasks be completed for one side of the motorcycle first before continuing to the opposite side. Route Turn Signal Wiring Through Rear Fender and Support 1. See Figure 5. Remove three rear screws (1) from fender support (2). 2. Loosen, but do not remove two front screws (3) from fender support. 1 3 2 is03285 1. Screw, rear (3) 2. Fender support 3. Screw, front (2) Figure 5. Fender Support Screws and Fender Support 3. Pull fender support away from rear fender to gain access to turn signal mount. 4. Remove stock screw and washer from turn signal mount. 5. See Figure 7. Pull turn signal (B) and turn signal mount (A) away from fender support. 6. Remove turn signal and wires from vehicle by routing turn signal wiring and connector through holes in rear fender and fender support. Gently guide wires through holes to ensure they do not get damaged. Feed Wiring and Install Relocation Bracket 1. See Figure 6. Feed turn signal wiring and connector through middle hole in turn signal relocation bracket and under rear of fender support. 1 is04635 1. Wire harness Figure 6. Wire Harness Routing 2. See Figure 7. Insert stock screw and washer through rear hole of relocation bracket (1) and turn signal mount (A). 3. Thread screw into turn signal (B). Tighten to 12-16 ft-lbs (16.3-21.7 Nm). 4. Align relocation bracket (1) with rear of fender support and install with screw (2) and nut (3) from kit. Tighten nut to 12-16 ft-lbs (16.3-21.7 Nm). Complete Turn Signal Relocation Wiring 1. See Figure 5. Install one rear screw (1) to hold fender support in place while routing wiring. Install screw snugly but do not fully tighten

Incoming search terms: