TOYOTA Upper/ Lower Windshield/ Rear Glass Tick Noise

0

Filed Under (Toyota Manuals) by admin on 12-10-2011

download
Upper/Lower Windshield/Rear Glass Tick Noise Service Category Vehicle Exterior Section Window/Glass Market USA Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMATION 2003-2009 4Runner, Avalon, Camry, Camry HV, Celica, Corolla, Echo, FJ Cruiser, Highlander, Highlander HV, Land Cruiser, MR2 Spyder, Matrix, Prius, RAV4, RAV4 EV, Sequoia, Sienna, Solar a, Tacoma, Tundra, Venza, Yar is TSB REVISION NOTICE •July 13,2009 Rev2: •The Warranty Information table has been updated. •February2,2009 Rev1: •Applicability has been updated to include 2009 model years. •Titlehasbeen updated. •Introduction has been updated. •Warranty has been updated. Any previous printedversions of this service bulletin should be discarded. TSB SUPERSESSION NOTICE The information contained in this TSB supersedes TSB No. NV009-06. •Applicability has been updated to include 2008 model year applicable vehicles. TSB No. NV009-06 is Obsolete and any printed versions should be discarded. Be sure tore view the entire content of this service bulletin before proceeding

HARLEY DAVIDSON CHROME 1.00 INCH (25.4 MM) DIAMETER HANDLEBAR KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 28-04-2011

download
INSTALLATION Preparation To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Refer to the Service Manual and follow the instructions given to remove the main fuse. 2. For FLTR models only: Refer to UPPER FAIRING AND WINDSHIELD: FLTR: OUTER FAIRING: REMOVAL in the Service Manual, and follow the instructions to remove the outer fairing. See INSTRUMENT NACELLE: FLTR: REMOVAL in the Service Manual, and remove the instrument nacelle and bezel. For ALL models: Direct contact of D.O.T. 4 brake fluid with eyes can cause irritation. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 4 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00240a)

HONDA GL1100 AM/FM RADIO INSTALLATION MANUAL/ WIRING DIAGRAM

0

Filed Under (Honda) by admin on 22-04-2011

download
INSTALLATION ■ Outline Procedures This section gives general information needed for mounting the individual radio components on and in the fairing. A) Fairing 1) Install radio on fairing before mounting fairing on motorcycle. (Remove fairing from your motorcycle when already mounted). 2) Remove fairing parts. 3) Drill unit mount holes. 4) Install six wire clips. 5) Install windshield on fairing before install- ing speakers. 6) Install radio indicator I on indicator panel II , then install indicator panel on fairing. 7) Install speakers III. 8) Install nutplate IV. 9) Install Power Amplifier in fairing. 10) Install radio funer VI. 11) Install the radio controller VII. 12) Install controller base panel VIII 13) Install radio switch sub-wire. 14) Connect adapter harness and wires inside fairing by working through left turn signal lens hole. B) Motorcycle frame and handlebar 1) Remove travel trunk and seat. Unscrew four shelter bolts (M6, one on each side at front and rear) to route antenna feeder. 2) Install antenna mount and antenna IX. 3) Route antenna feeder along the frame tube. 4) Install radio switch X on left handlebar lever bracket and route the wires. 3 of 11 Page 4 C) Fairing instllation 1) Install fairing on motorcycle. 2) Connect motorcycle wire harness 9-P coupler to fairing wire 9-P coupler. 3) Connect radio switch wire to switch sub- wire.4) Connect antenna feeder. 5) Confirm that radio operates properly. Reinstall parts removed in step 2 or (A) and in step 1 of (B). REWORKING ■ Remove Fairing and Fairing Parts (Fig.10) 1) Install radio on fairing before mounting fairing on motorcycle. (Remove fairing from your motorcycle when already mounted). 2) Remove right and left fairing pockets, right and left turn signal lenses, right and left nutplates, left hole cover and indi- cator base panel from fairing. (Fig.10) Fig. 10 LEI-1 NU I PLATE 4 of 11■ Reworking on Fairing — Speaker mounting holes- 1) Remove 18 mm grommet. 2) Lightly roll template so that it will follow contour of fairing snugly. 3) Position template on fairing with its upper and outer edges aligned with those offairing as indicated by arrows. 4) Attach template to fairing using adhesive tape where shown. 5) Punch mark centers of four holes with a
drift and hammer. 6) Drill 6 mm holes through marked centers. To obtain a more balanced response with richer, deeper bases, drill two 50 mm holes in the fairing so as to link the speaker box with the inside of the fairing. Fig. 11-1
—Power amplifier mounting holes- 7) Drill two 5.5 mm holes through concaves in fairing. Fig. 11-2 RIGHT HAND SHOWN, LEFT SIMILAR ADHESIVE TAPE

Incoming search terms:

HARLEY DAVIDSON WINDSHIELD MOUNTING HARDWARE KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 14-04-2011

download
This kit contains the following items: ITEMDESCRIPTION/ QUANTITY PART NO. 1 Stud, double ended, 5/16-18 (4) 3265A 2 Bushing (4) 67621-94 3 Acorn nut, keps, 5/16-18 (Chrome) (4) 7992 Installation 1. Using a T-40 TORX drive head, remove the upper left- side chrome button-head fork screw and chrome flat washer and discard. 2. See Figure 1. Obtain a double-ended stud (1) and chrome acorn nut (3) from the kit. Thread the nut onto the NON lock patch side of the stud and hand tighten. NOTE Position the clamp so the clutch cable is to the rear of the stud. 3. Slide the clutch cable clamp (4), along with the cable, into position on the stud as shown. Assemble a bushing (2) from the kit onto the stud threads. 4. Insert the lock patch side of the stud through the headlamp nacelle and into the upper fork bracket. Tighten the acorn nut and stud to 15-20 ft – lbs (20-27 Nm). 5. Continue, one at a time, replacing the three remaining chrome button-head fork screws and flat washers with the studs, bushings and chrome acorn nuts from the kit. Tighten to 15-20 ft – lbs (20-27 Nm)

HARLEY DAVIDSON FXSTD DETACHABLE WINDSHIELD AND DOCKING HARDWARE KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-03-2011

download
INSTALLATION NOTE Use the Docking Hardware Kit to assemble two upper and two lower clamps. See the Service Parts illustration. The upper clamps use a mounting pin (4) and the lower clamps use a button head screw (5) to fasten the windshield mounting bushing. 1. Assemble the windshield docking hardware as follows: a. Install a larger chrome washer (6) and bushing (7) onto a button head screw (5). Thread the screw into the boss on one of the clamps (1), and tighten finger tight. Repeat for a second lower clamp. b. Install a larger chrome washer (6) and bushing (7) onto a mounting pin (4). Thread the pin into the boss on one of the clamps (1), and tighten finger tight. Repeat for a second lower clamp. 2 1 3 4 4 5 is 02187 1. Upper clamp 2. Lower clamp 3. Fork tubes 4.1/8 inch (3 mm) approximately 5.3.0 inch (76 mm) Figure 1. Installing Clamps NOTE Place shop rags on the headlamp, front fender and front of the fuel tank to prevent scratches to these components. Be sure the windshield assembly does not contact chrome or painted parts. Contact will cause scratches to chrome or painted parts. 2. See Figure 1. Install a lower clamp onto a fork tube using a smaller chrome washer and lock nut from the kit. Adjust so the clamp is approximately 1/8 inch (3 mm) from the top of the lower triple clamp, then finger tighten the lock nut. Repeat with the second lower clamp and fork tube. NOTE Keep front wheel straight to prevent brackets from scratching fuel tanks. See Figure 1. Install the clamps on the fork tubes so the bushing center lines are 3 inches (76 mm) apart. 3. Install an upper clamp onto a fork tube using a smaller chrome washer and lock nut from the kit. Adjust so the clamp is approximately 1/8 inch (3 mm) from the bottom of the upper triple clamp. Ensure that the center lines of the upper and lower bushings are 3 inches (76 mm) apart, then finger tighten the lock nut. Repeat with the second upper clamp and fork tube

DETACHABLE KING SIZE WINDSHIELD FOR SOFTAIL MODELS WITH CHROME HEADLAMP NACELLE OR STREET STALKER HEADLAMP NACELLE (WITHOUT PASSING LAMPS)

0

Filed Under (Harley Davidson) by admin on 07-03-2011

download
Installation 1. Remove upper screws that attach the chrome headlamp nacelle to the front forks. 2. See Service Parts illustration. Attach the upper docking bushings (22) using washer (21) and mushroom head screws (20) Use Loctite 242 (blue) on screw threads. Torque screws to 19 ft-lbs (25.8 Nm). 3. Remove lower screws that attach the chrome headlamp nacelle to the front forks. 4a. For vehicles equipped with the Chrome Headlamp Nacelle, attach the lower docking bushing (22) using washer (21) and button head screw (23). 4b. For vehicles equipped with the Street Stalker Headlamp Nacelle, attach the lower docking bushing (22) using washer (21) and button head screw (24). Installing/Removing Windshield 1. Carefully lock bottom windshield assembly jaws into grooves of the lower rubber docking bushings. 2. Hook the top windshield assembly jaws into grooves of the upper rubber docking bushings. 3. Firmly press the windshield into place until seated on docking bushings. 4. To remove windshield, grab windshield edges on each side of center brace and firmly pull windshield loose from docking bushings. 1 WARNING Carefully inspect windshield upon completion of installation. Be sure windshield mounting does not restrict full left or full right movement of front fork assembly. Restricted movement could affect handling, resulting in personal injury. If restriction does occur, adjust windshield as needed until proper clearance is obtained. Have experienced Harley-Davidson service personnel correct any problems before riding with this accessory installed. 1 CAUTION Check mounting hardware periodically. Never ride with loose mounts. A loose mounting causes extra stress on all other mounts, as well as the windshield itself, and could result in premature failure of either or both. 1 CAUTION Do not clean Lexan®polycarbonate in hot sun or high temperature. Powdered, abrasive or alkaline cleanser will damage the windshield. Never scrape the windshield with a razor blade or other sharp instruments because permanent damage will result. Sunlight reflections off of the inside curvature of a windshield can, at certain times of the day, cause extreme heat build-up on motorcycle instruments. Exercise care in parking. Park facing the sun, place an opaque object over the instruments, or adjust the windshield to avoid reflections. Harley-Davidson windshields are made of Lexan®. Lexan®is a more durable and distortion-resistant material than other types of motorcycle windshield material, but still requires attention and care to maintain. • Do not use liquid windshield “protectors” on your windshield. Although they may work well on automobile safety glass, Harley-Davidson cannot ensure the results when used on Lexan®Harley- Davidson windshields. If you want to use a windshield protectant on your windshield, try Harley Glaze Polish and Sealant®. • Do not use benzine, paint thinner, gasoline, or other types of harsh cleaning agents on windshield. They will damage the windshield surface. • Do not use benzine, paint thinner, gasoline, lubricants (including Armorall), or other cleaning agents on the rubber bushings. They will damage the bushing surfaces

Incoming search terms:

HARLEY DAVIDSON HERITAGE SOFTAIL WIND DEFLECTORS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-03-2011

download
This kit is designed for 1986 and later FLSTC, FLST, FLSTF and FLSTN model motorcycles equipped with a windshield and/or passing lamps. If your FLST, FLSTC, FLSTF or FLSTN is equipped with a windshield but not a passing lamp assembly, you will need two washers 5/16 x 1 x 1/8 in. (HD Part Number 6645). These washers will be used as spacers for the bottom of the deflector. This kit is also designed to fit with accessory five gallon Fat Bob Gas Tanks. Installation 1. See Figures 1 and 2. On Rigid Mount Windshields, remove the bolts (1), lockwashers (2), and flat washers (3) securing one side of the windshield support bracket. Save all hardware for reinstallation. NOTE On Rigid Mount Windshields, be sure the large spacer (4) between the tip of the windshield support bracket and the fork stays in position. On Detachable Windshields, remove the bolts (1) and flat washers (2) securing one side of the windshield support bracket. Save all hardware for reinstallation. 2. Place the wind deflector in position and install the hardware removed in Step 1. Do not tighten the bolt at this time. NOTE On Rigid Mount Windshields, be sure you install the large spacer between the windshield support bracket and the fork. NOTE On 2000 and later models, be sure the wind deflector is outside of the windshield docking points. 3. Position the wind deflector parallel with the fork leg and install the other flat washers, lockwashers and bolts. Do not tighten the bolts at this time. NOTE If you have a motorcycle equipped with a windshield, but no passing lamps assembly, use the washer (6645) to space the deflector away from the fork leg. 4. Position the wind deflector so it does not touch the bottom of the windshield or the turn signal. The deflector bolt holes are slotted for th is purpose. 5. When the deflector is correctly positioned, tighten the bolts to 17 ft-lbs (23 Nm). 6. Repeat steps 1-5 for the opposite side of the vehicle

Incoming search terms:

HONDA GL1200 HEADLIGHT BEZEL WITH GRILL MOUNTING INSTRUCTIONS

0

Filed Under (Honda) by admin on 27-02-2011

download
Read instructions thoroughly before installing. 1. Place bike on center stand. 2. Take windshield panel off per service manual instructions. 3. Take lower grill out. Replace the metal bracket under the windshield with the replacement bracket provided. 4. Reinstall the windshield panel in the reverse order of removal.

HARLEY DAVIDSON V-LOGO TURN SIGNAL INDICATOR FORROAD KING INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 25-02-2011

download
1. Disconnect battery cables, negative cable first. 2. Following instructions in applicable Service Manual, remove the windshield. 3. Remove the phillips screw at the bottom of the of the headlamp door (chrome ring). Remove the headlamp door. 4. Remove the seven Phillips screws to free the headlamp housing from the headlamp nacelle. 5. Squeeze the two external tabs (if present) to remove the wire connector at the back of the headlamp bulb. Remove the headlamp housing assembly and set aside. 6. See Figure 1. Reaching inside the headlamp nacelle, remove the speed nut to release the chrome strip at the top of the nacelle. 7. Remove the wire form clip holding the halves of the nacelle together at the bottom. 8. Carefully pry off the fork lock plate at the rear of the handlebar clamp shroud. Remove two Phillips screws beneath the lock plate. 9. Loosen the Phillips screw from the tab at the front of the handlebar clamp shroud (but do not remove). 10. Loosen the two acorn nuts from the left and right side fork studs. 11. Raise the handlebar clamp shroud slightly, and while separating the halves of the headlamp nacelle, remove the shroud from the vehicle. 12. Carefully align the template over the handlebar shroud cover and tape into place. 13. Exercising caution to avoid scratching, secure the shroud in a vise or use other suitable means. 14. Use a center punch and carefully punch the drill hole locations. See Figure 2. Make sure to punch indentation deep enough to keep the bit from skating during the drilling procedure. 15. Drill one 1/4″ hole and two 5/32″ holes as indicated on the Drill Template (attached)

HARLEY DAVIDSON FAIRING MOUNT MIRRORS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-02-2011

download
INSTALLATION Removing Outer Fairing 1. Standing at the front of the vehicle, use a T-27 TORX® drive head to remove the three outer fairing screws (with flat washers) just below the windshield. 2. Moving to the inner fairing side, use a T-27 TORX drive head to remove the two fairing screws just above the wind deflectors on the left and right side. 3. Turn the handlebar to the right and remove the outer fairing screw (reach in below the fairing cap). Turn the handlebar to the left and remove the fairing screw on the opposite side. 4. Tilting the outer fairing toward the front, squeeze the two external tabs to remove the wire connector at the back of the headlamp assembly. 5. Lift the fairing (with headlamp assembly) off the motor- cycle. NOTE Since the outer fairing screws hold the windshield in place, the windshield may fall to the floor if not removed. 6. Remove the Windshield. Installing Mirrors 1. See Figure 1. Place template on inside of fairing as shown to locate mounting holes for mirror. 2. Begin by drilling a 1/8 inch pilot hole at each location marked on the template. For the center hole (2) where the 3/8 inch threaded stud passes through the fairing use a 13/32 inch diameter twist drill to drill the hole to its final size. For the alignment hole (1), use a 7/32 inch diameter twist drill to drill the hole to the final size. 2 1 is 02115 1.7/32 inch hole location 2.13/32 inch hole location Figure 1. Positioning Template 1 is06315 1. Auxiliary mirror Figure 2. Orientation of Auxiliary Mirror NOTE The flange nut is a self locking nut and must not be tightened more than 30 in-lbs (3.4 Nm). 3. See Figure 3. Place mirror (2) in position and install backing plate (4) with the raised post (B) (with the L and R marking) toward the nut surface. Install the flange nut (6) and tighten nut to 20-30 in-lbs (2.3-3.4 Nm). 4. See Figure 2. Position the mirror so the round auxiliary mirror is in the upper inside corner position. 5. Repeat for right side