Suzuki M- 109 Front Head Pipe Installation Manuals

0

Filed Under (Suzuki) by admin on 18-02-2012

download
1. Remove seat (Fig 1) remove right side (Fig 2) panel with allen 6mm bolt and push-pin snap. (Fig 3) Figure 1 Figure 2 Figure 3
- 3 – 2. Remove 6mm bolt on heat shield and remove heat shield. (Fig 4) Figure 4 3. Remove two 8mm bolts on top muffler and remove two 8mm stock bolts on bottom muffler and remove mufflers. (Fig.5 & 6) Figure 5 Figure 6 4. Remove frame cover with stock allen 6mm bolt. (Fig 7) Figure 7 FFF – 4 – 5. Loosen brake pedal bolts to allow more room to remove the exhaust. (Fig 8) Figure 8 6. Remove exhaust system by removing stock 8mm bolts on exhaust flanges. (Fig 9) Figure 9 7. Unplug EXCVA wire connectors. (Fig 10) Figure 10 – 5 – 8. Remove three 8mm stock mufflers mounting brackets bolts as shown. (Fig 11) Figure 11 ffff 9. Remove EXCVA unit from the stock muffler bracket. (Fig 12) Figure 12 10. Remove the stock pulley from the EXCVA actuator unit as shown. (Fig 13)

Incoming search terms:

GL 1200 CB TRANSCEIVER Installation Manual

0

Filed Under (Honda) by admin on 21-11-2011

download
Remove the right and left side covers. Disconnect the battery negative cable from the battery negative terminal.
2) Remove the left fairing pocket Remove the Auto volume control unit. -1 Remove the CB blind cover from the fairing by removing the four 5 x 22 mm socket head bolts. (Fig. 2) Disconnect the three wire connectors of the auto volume unit. (Fig. 3) -2 Remove the two 4 x 12mm tapping screws and remove the knob and nut from the auto volume control unit. (Fig. 1) -3 Remove the bracket form the auto volume control unit. NOTE: Discard the CB blind cover, 4 x 22mm tapping screws, and bracket. 4) Remove the seat. 5) Remove the shelter NOTE: To remove the front of the shelter, it is necessary to remove the inner cover by lifting the rear of the cover. 6) Remove the two tapping screws attaching the left coupler cover and move the holder towards the center. 7) Remove the main amplifier. -1 Disconnect the main amplifier 2-P black connector. -2 Straighten the four wire clamps at the main amplifier to release the harnesses. -3 Remove the two nuts and washers holding the main amplifier; pull the amplifier out between the left fairing pocket and handlebar by pulling up on the bottom. 8) Connect the two DIN connectors if the transceiver harness (65) to the terminal component (62) color-to-color (Fig. 7). 9) Remove the seals from the terminal component mounts inside the fairing. Position the terminal component (62) on the mounts and install using cap nuts (69) and washers (72). NOTE: Use care when installing the terminal component (62) not to push in the audio harness, CB harness and terminal component harness into the fairing pocket

The Honda VTX 1300 Keyless Ignition Switch Installation instructions

0

Filed Under (Honda) by admin on 04-11-2011

download
Remove the seat from the motorcycle.2. Lift the ignition module off of the battery cover and let it drape over the side of the motorcycle. 3. Remove the battery cover and disconnect the negative battery cable. 4. Remove the gas tank and set it aside. There is a vent line at the right rear of the tank, a vacuum line and the gas feed line on the left side of the tank at the petcock, and two speedometer connectors at the left front of the gas tank. 5. Remove the clip from the top of the steering head cover and remove the right hand side cover. See picture at right. 6. Remove the headlight to expose the wiring connectors inside the headlight shell. 7. Remove the left-hand side cover. On the left side of the frame is an electrical wire shroud wire tied to the left side of the frame with a reusable wire tie. Inside this cover is the 3-pin connector that connects the ignition switch to the bike’s wiring harness. Pull the small lever back to release the wire tie and remove the wire tie. Pull back the wire shroud to reveal the wire connectors inside. Disconnect the 3-pin connector that comes from the ignition switch. Remove the two bolts holding the ignition switch to the bike’s frame. See Picture at right. Remove the ignition switch from the bike. You may have to remove the connector body from the ignition switch wires to slide the wires through the frame when removing the ignition switch. You may now reinstall the side cover. 8. Lay the new wiring harness along the backbone of the bike with the two 9-pin connectors at the headlight and the 6-pin and 3-pin connectors at the battery. Insert the two 9-pin connectors through the large hole in the back of the headlight shell. Inside the headlight shell is a red 9-pin connector. Disconnect this red 9-pin connector and insert the new wiring harness connecting each side to the red 9-pin connectors. See picture at right

HARLEY DAVIDSON SPORSTER, DYNA AND SOFTAIL LICENSE / TURN SIGNAL RELOCATOR INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
1. Remove the license plate. Remove the license plate mounting bracket from the fender. Remove the two screws from the tail light lens and pull the light outward, unplug the wire connector and set aside. Unplug the turn signal wire connectors from the tail light base and push them out thru the hole in the fender. Looking up underneath the rear fender remove the wires from the clips that secure them to the bottom side of the fender. Cut the wires 2″ from the plugs as shown in photo 1. 2. Unscrew the signal housings from their mounting stems while rotating the wires on the inside of the fender so as not to twist them off while unscrewing the signal from the stem. Remove the signals pushing the wires thru from the inside while pulling the signal outward. Remove the nuts from the backside of the fender that secure the stems and remove the stems. 3. Assemble the license/turn signal bracket, turn signals. Place the smaller reinforcing bracket inside the license plate bracket. Locate the two supplied 5/16″ X 1″ bolts with holes drilled thru the center and the two supplied 5/16″ long spacers. Place the bolts thru the brackets from the inside, threads facing outward followed by the spacers. Thread the wires of the signals thru the bolts and thread the bolts into the signals and snug the bolts. 4. Mounting the LED lights a. Locate the supplied LED tail/brake lights. NOTE: this license plate holder is designed for the new U.S. standardized 7″ wide license plate. If you have an old style wider plate call us at the phone number below and we will send you a separate set of chrome brackets to work with your larger plate at no charge. b. Install the lights as shown in photos 2 & 3. Thread the wires of the LED lights thru the lower holes in the license bracket, peel the adhesive backing and press them firmly in place. Cut the wires off at about 18″ long. c. Install the license plate bracket with signals and LED lights onto the rear fender as shown in photos 2 & 3. Place the two supplied 1/4″ X 1″ flat head screws thru the license plate mounting block. Notice that the thicker half of the mounting block goes toward the top of the fender. d. Next route all the wires from the right turn signal and LED into the slot or notch on the backside of the mounting block followed by the rubber mounting gasket. Install the two nuts from the underside of the fender (Removed from the original license bracket.) onto the two flat head screws and snug them being sure the wires are all in the slot of the mounting block. Run all of the signal and LED wires thru the hole in the fender to the left of the mounting block. e. Install the license plate assembly onto the mounting block using the two supplied 1/4″ X 1/2″ flat head screws. Check the slack from all the wires and again be sure the wires are not pinched between the mounting block and the fender. Tighten all four flat head screws securely. Align the turn signals and tighten their mounting bolts securely.

Incoming search terms:

Incoming search terms: