2006 KTM 250 SX-F 250 EXC RACING 400 EXC RACING 450 SX, XC, EXC RACING 525 SX, XC, EXC RACING, REPAIR MANUAL

0

Filed Under (KTM) by admin on 05-05-2012

download
Hot start lever (250 SX-F) If you pull the red hot start lever [1] during the starting procedure backward, a bore in the carburetor will be opened through which the engine may take in additional air. The result is a „lean” fuel-air mixture of the type needed for hot starts.
ENGLISH 7 OPERATION INSTRUMENTS » Headlamp switch (EXCUSA) In this model the headlamp is switched on with the pull switch [1] . Flasher switch The flasher switch is a separate unit and is mounted on the left portion of the handlebar. The wire harness is designed in a way that whenever you want to use your bike off-road, you can dismount the entire turn indicator system without affecting the function of the remaining electrical system. Flasher left Flasher right Starter button (EXC) Pushing the black starter button [2] will actuate the E-starter. Emergency OFF switch (EXC Australia) The red emergency-OFF switch [3] is arranged adjacent to the throttle grip. In this position, the E-starter is operational and the engine can be started. In this position, the E-starter and ignition circuits are interrupted.The E-starter cannot be actuated, and the engine will not start, not even if you attempt to start it with the kickstarter. Pushing the black starter button [4] will actuate the E-starter. 2 3 4 5 6 Indicator lamps The green control lamp [5] flashes in the same rhythm as the flashing indicator when the indicator is working. The blue control lamp [6] lights up when the high beam is on

Incoming search terms:

CYCLE SOUNDS T-TAP POWER HARNESS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 21-04-2012

download
This t-tap plug is designed to work with Cycle Sounds audio systems. However it can be used to wire many add on 12 volt accessories to you Harley Davidson motorcycle. This plug is rated for 6-8 amps of power and should not be used for adding any product that is rated for more than the t-tap plug is rated for. Take the time to check the products power rating for which you want to install to make sure it is compatible with the t-taps amperage rating. Failure to do so couldlead to electrical failures, which could result in serious injuries or even death. it is possible to overload your motorcycles charging system by adding too many electrical accessories. U se amp meter to verify all power connections. Also check product power ratings for anything you are trying to install. Exceeding the maximum amperage can lead to electrical failures, which could result in serious injuries or even death. INSTRUCTIONS: Step 1: remove seat on bike and locate the wire harness under the seat that matches the plugs on the t-tap harness (2120-0026.) Location may vary between bike models. Step 2: unplug bike harness and snap each end of t-tap harness in correct plug opening. When finished connect power wires to the male plug.(all Cycle Sounds audio systems come pre wired with correct wire colors and terminals). When using this t-tap for any other 12 volt accessory, make sure the red and black wires are snapped into their proper pin connectors. Kit does not come with power terminals for the accessories device. See your local bike dealer for purchase of terminals

HARLEY DAVIDSON IGNITION MODULE INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 23-03-2012

download
Step 1: Apply a thin coat of silicone grease to the bottom of the module before mounting the module to its plate in the distributor. Step 2: Slide the three wires from the MODULE, through the grommet, to outside the distributor housing. Put the three wires from the MODULE in the TERMINAL PIN HOUSING: GREEN WIRE in hole #1, BROWN WIRE in hole #2, RED WIRE in hole #3. Plug the three wire harness (PN 29349, not supplied with this kit) into the TERMINAL PIN HOUSING. RED WIRE: Power/voltage for the MODULE. Connect to coil (+) terminal. GREEN WIRE: Ignition trigger. Connect to coil (-) terminal. BROWN WIRE: Ground for the MODULE. Connect to ENGINE BLOCK GROUND. Clean away any grease, oil, and paint from the mounting surface before the connection is made.

Harley-Davidson FXWG, FXST (all except FXSTS), FXDWG Light Bar INSTALLATION AND OWNER'S MANUAL

0

Filed Under (Harley Davidson) by admin on 20-03-2012

download
1. Put a pair of male and female clamp halves together just above the lower triple-clamp. Squeeze the ends of the clamp together with a pair of pliers. Diagram A. 2. Have an assistant position the Light Bar Assembly so the lightbar bracket is to the outside of the clamp assembly. Make sure the wires from the Light Bar Assembly are below the lower triple clamp. Diagram B. 3. Insert a Screw through the clamp and Light Bar Assembly mounting bracket and thread on an Acorn Nut. 4. Hold the Light Bar Assembly in place in front of the lower triple clamp, assemble and attach the remaining clamps. 5. With all four clamp assemblies in place, tighten the clamping screws and nuts to 15 ft. lbs. (21 Nm). Refer to the service manual to gain access to the wire harness inside the fuel tank tunnel or inside the frame backbone. Also, verify the appropriate color wires for hook-up of the passing lamps and turnsignals and running lights. Route the wires from the Light Bar Assembly, around the lower triple- clamp, and up to the frame backbone. Secure the wires so they cannot become pinched when turning the fork. A. The short black wires from the Light Bar Assembly connect to the wires powering the running lights. B. The short red wires from the Light Bar Assembly connect to the wires powering the turnsignals. C. The long blue wires from the Light Bar Assembly connect to the wire powering the headlight low beam. After the wires are connected, verify the operation of the passing lamps, running lights and turnsignals. Correct any connection problems before reassembling the motorcycle. Reinstall the fuel tank. Check all fasteners used during this installation for tightness

Harley-Davidson MSD Pulse Ignition Installation Manual

0

Filed Under (Harley Davidson) by admin on 11-03-2012

download
PICKUP PLATE INSTALLATION Remove the existing trigger/points plate and rotor, points cam and advance. Refer to the bike’s Service Manual for the proper procedure. EVOLUTION AND LATE MODEL SHOVELHEAD V-TWINS 1. From inside the cam/ignition housing, feed the free end of the MSD pickup harness through the wire access port. Note: The harness includes a heat-resistant acrylic sleeve that fits snugly inside the port opening. Do not pull the sleeve completely through the port. It must be positioned to protect the wires as they pass through the port opening. 2. Mount the MSD pickup plate inside the housing (Figure 1). Note the “adjusting notch” on the edge of the plate. This notch must be located over the series of “steps” inside the housing (about the 7 o’clock position as you face the housing). One of the sensor units will be at approximately 12 o’clock. SPORTSTER MODELS 1. On Sportsters, the wire access port must be enlarged. Use a 9/32″ drill bit to enlarge the wire port. 2. Remove the wire harness clamp of the pickup assembly and route the wires through the port. 3. Mount the MSD pickup plate inside the housing (Figure 2). Note the “adjusting notch on the edge of the plate. This notch must be located over the “cast notch” inside the housing (about the 11 o’clock position as you face the housing). The shorter of the two sensors will be approximately in the 9 o’clock position. 4. Install the hold-down/standoff screws with flat washers until they are snug – do not tighten at this time (Figure 3). 3. Put the MSD rotor in place on the end of the camshaft. The locating pin in the rotor bore must align with the groove in the cam. Do not force the rotor on the camshaft! Push the rotor into place until it is tightly against the end of the cam then snug the retaining screw. 4. Check the distance from the outer surface of the pickup plate to the end of the installed rotor (Figure 4). If necessary, add shims until the measured rotor height is 9/16″ (+/- 1/32″). 5. When the rotor height has been verified, remove the retaining screw, place a drop of Red Loctite on the threads and reinstall the screw to the factory recommended torque

Incoming search terms:

Harley Davidson Motorcycle 1982-2009 Standard Signal Mirror Kit INSTALLATION

0

Filed Under (Harley Davidson) by admin on 23-02-2012

download
Remove the 5/ 16 ” bolt from the mounting stem on the Signal® mirror. While seated on the motorcycle, position the Signal® mirror on the handle bar. Secure the Signal® mirror to the handle bar using the 5/ 16 ” bolt. NOTE: Use of oil is suggested if bolts do not thread easily into stem base. Make sure the bolt is tight! Guide the Signal® mirror wire harness into the cowling by going along side the existing factory wire harness. 4 Remove any slack in the wire harness. Secure the wire harness to the handle bar using a supplied tie wrap. 5 6 Adjust the position of the Signal® mirror and tighten the ball retention screws. Start on either the left or right side mirror. These instructions start with the right side mirror. Remove the factory mirror. NOTE: For motorcycles with OEM forward facing indicators, please use the instructions on the last page in lieu of step 2.

KTM ELECTRICAL SYSTEMS INSTALLATION, REPAIR

0

Filed Under (KTM) by admin on 02-02-2012

download
DC SYSTEMS STEP DC1 – REGULATOR/RECTIFIER: PRE-2005 KTM If the stock regulator looks like below (the stock connector will not plug into the Trail Tech regulator/rectifier) then the provided stub connector must be soldered into the bike’s wire harness. For models without a stock battery, mount the reg/rec and plug the stub connector into it. Run the red and black wires directly to the (aftermarket) battery, and the yellow wires to the stator. SEE DC CIRCUIT DIAGRAM ON REVERSE SIDE OF PAGE. MODELS WITHOUT A STOCK BATTERY Move stock light to the DC circuit: divert lighting wire from AC circuit to DC circuit. In stock form, the lights are powered by the AC half of the electrical system. In order to continue to use the stock light, find the yellow wire (runs to stock headlight) shown below (wire bundles are found underneath gas tank) and cut the smaller gauge yellow wire. 1. Connect aftermarket light: Wire the light’s red(+) light lead to the positive(+) battery terminal, and the black(-) light lead to the negative(-) battery terminal. Trail Tech lights should use a 10-20 amp fuse as close to the positive(+) battery terminal as possible.

Yamaha TW200N/ TW200NC SPECIFICATIONS AND SUPPLEMENTARY SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 26-04-2011

download
GENERAL INFORMATION MOTORCYCLE IDENTIFICATION EAS00017 VEHICLE IDENTIFICATION NUMBER The vehicle identification number 1 is stamped into the right side of the steering head pipe. EAS00018 MODEL CODE The model code label 1 is affixed to the frame. This information will be needed to order spare parts CABLE ROUTING 1 Throttle cable 2 Front brake light switch lead 3 Right handlebar switch lead 4 Clutch cable 5 Left handlebar switch lead 6 Clutch switch lead 7 Front turn signal/position light lead (left) 8 Main switch lead 9 Indicator lights lead 0  Speedometer cable A Meter light lead B Headlight coupler C Wire harness D Front turn signal/position light lead (right) E Brake hose ب Fasten the brake hose with a plastic locking tie to the brake hose grommet. ة Fasten the wire harness with a plastic locking tie PERIODIC CHECKS AND ADJUSTMENTS INTRODUCTION This chapter includes all information necessary to perform recommended checks and abjustments.If followed, these preventive maintenance procedures will ensure more reliable vehicle operation, a longer service life and reduce the need for costly overhaul work.This information applies to vehicles already in service as well as to new vehicles that are being prepared for sale.All service technicians should be familiar with this entire chapter. PERIODIC MAINTENANCE CHART FOR EMISSION CONTROL SYSTEM

YAMAHA YZF-R6R/ YZF-R6SR/ YZF-R6RC/ YZF-R6SRC SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 26-04-2011

download
CABLE ROUTING SPEC A Pass the right handlebar switch lead inside the front brake hoses and over the throttle cables. B Install the throttle cables to the hook so that the pulling side of the throttle cables is routed downward. C Pass the clutch cable through the guide. D Plastic locking tie shall be positioned at 10 mm (0.39 in.) below from the upper bracket. E Clamp the left handlebar switch lead to the front fork with the plastic locking tie and cut the tip of the tie. Clamp it to the protector section Set in the coupler between the head light’s hollow section and the duct. J Install the relay to the rib of the head light. (Location for the left and right relays is alternative.) K To the wire harness L To the front turn signal light (right) M Set the sub wire harness in the joint. N Do not catch the sub wire harness when the duct is assembled. O To the front turn signal light (left) P Point the tip of the plastic locking tie to the front side of the vehicle. Cut the tip leaving 2 X 10 mm (0.08 X 0.39 in). Q Point the tip of the plastic locking tie under the under bracket and rear side of the vehicle. Cut the tip leaving 2 X 10 mm (0.08 X 0.39 in) A Pass the main switch lead under the left handlebar switch lead and then to the right side of the vehicle. B Pass the throttle stop cable by the left side of the side stand switch lead, oil level switch lead, A.C. magneto lead and then to the right side of the vehicle. C Pass the fuel tank drain hose and fuel tank breather hose inside of the reservoir tank breather hose, reservoir tank hose and wire harness and then route it by the out side of the starter motor lead. D Pass the coolant reservoir tank hose outside of the fuel tank drain hose and fuel tank breather hose. E Pass the fuel tank drain hose, fuel tank breather hose through the clamp of the coolant reservoir tank

Incoming search terms:

HONDA GL1000 DYNA S ELECTRONIC IGNITION INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 24-04-2011

download
open the top and side compartments. Locate the two ignition coils and ballast resistor directly in front of the air cleaner intake. On some models it is best to remove the air cleaner for access to the coil area. Unplug the wires from the ballast resistor. Connect the power resistor supplied with the kit across (parallel with] the ballast resistor, and reconnect the wires to the tabs provided. The resistor will become very hot during operation. That is normal, and not destructive to the resistor, however, care should be taken to keep cables and wires from coming in contact with it. Locate the blinker relay just behind the fuse box in the left compartment. The white/green wire going to the relay carries 12 volts from the ignition switch. Using the splice connector provided, attach the separate red wire included in the kit to the white/green wire, as shown below. Do not strip the wires. On 197B and 1979 models, the 12 volts can be obtained at the accessory terminal in the left side compartment. y^T^^TL. PUSH CLIP DOWN RED WIRE SUPPLIED WITH KIT SWITCHED 12 VOLTS Remove the points cover and battery cover. Remove the 10 mm bolt holding the spark advance assembly to the engine. Remove the screws holding the points plate to the engine. Disconnect the blue/yellow
and yellow point wires where they plug into the wire harness and remove the entire point/plate assembly. Notice that there are two other wires connected where the points plugged in. These are wires going to the condensers mounted in front of the battery. Unplug both wires and tuck them back out of the way. Do not reconnect. | > Remove the spark advance assembly from the engine. Remove the point cam from the advance assembly. Coat the advance assembly shaft with oil. Place the OYNA S rotor on the shaft and while spreading the weights, push the rotor down until it engages the weights. Ensure that the rotor rotates freely on the shaft as the advance weights move out and back. Install the advance/rotor assembly on the engine making sure the pin on the camshaft is engaged in the slot on the advance assembly. Install the washer and bolt, and tighten. Ensure that the rotor is still free to rotate.

Incoming search terms:

Incoming search terms: