MC 1200 Motorcycle Trailer – 1200 lbs Assembly Instructions

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
Tongue: Remove tongue assembly from the frame bundle. Insert into the tongue channel and slide into the front cross member of the frame. Secure with two (2) 3/8″ X 4″ carriage bolts and 3/8″ flange lock nuts. Tighten. Thread the tongue wire harness through the front top hole in the tongue and pull out the hole provided in the left side of the tongue towards the rear. Connect to the frame harness with the plugs provided. Install grommets. Safety Chains: Insert a 3/8″ X 1-1/4″ hex bolt into a 3/8″ flat washer, safety chain and then through the lower hole on the front of the tongue. Place on a 3/8″ flat washer on the inside of the tongue and secure with 3/8″ flange lock nuts. Repeat procedure on the opposite side of the tongue. Tighten. Coupler: Mount the coupler onto the tongue with a 1/2″ X 4″ hex bolt trough the rear mounting holes of the coupler. Using two (2) 1/2″ X 1″ hex bolt attach the coupler to the tongue using the front mounting holes. Secure with flange lock nuts. Tighten. Axle: Attach the spring busing in the rear spring shackles with 1/2″ X 3- 1/4″ hex bolts and 1/2″ flange lock nuts. Position the axle under the trailer with spring eye to the front of the trailer. Slip the flat end of the spring in the rear spring shackle above the bushing just installed. Secure the front spring eye to the front spring shackle with 98/16″ X 3-1/4″ hex bolts and 9/16″ hex lock nuts. Tighten. Mount the tire and rim assemblies to the axle assembly with 1/2″ lug nuts and tighten to 80-90 ft./lbs. of torque using the rotation pattern as shown in the Shore Land’r Owners Manual . Retorque the lug nuts after 50 miles of driving and then periodically thereafter. Ramps: Locate the loading ramp. Note that one end has two holes punched in the bottom of the channel. (See parts drawing) Insert a 3/8″ X 1-1/2″ full threaded carriage bolt into one of these holes. Secure in this position using a 3/8″ flange lock nut. Tighten Place a second 3/8″ flange lock nut onto the same bolt only until the threads of the bolt are exposed through the nut locking it in

Incoming search terms:

Power Grid LED Integrated Tail Light General Installation Instructions

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
Running Light, Brake Light and Blinker Function The triple wire harness plugs directly into the OEM wire harness designed for the stock tail light. Optional integrated turn signals are designated by Yellow and Blue wires coming off of the harness connected to the DMP LED Integrated Tail Light. If you are sitting on the bike the yellow wire connects to the right side blinker and the blue wire connects to the left side blinker. Installation DMP LED Integrated Tail Lights are designed to replace the OEM factory unit with the use of OEM original hardware. Pay close attention during the disassembly process to ensure proper assembly later. Tip: During disassembly it might be useful to use a small digital camera or camera phone to remind the installer where things go in conjunction with the OEM factory service manual. Test Function NOTE: Double check before you test the functionality of your new DMP tail light, make sure there are no crossed or short circuited connections before you reconnect the battery. If your new DMP tail light is not operating properly please check all your connections thoroughly

Incoming search terms:

Street Magic Magical Wizards LED Installation Instructions

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
1. Always wear appropriate safety gear including safety glasses when soldering or performing any electrical work. It is highly recommended that safety glasses be worn throughout this installation process. Temperature of bike must be at least 60 degrees F. for tape to properly cure. Read all directions before starting project. 2. Turn fuel supply valve to off position before starting. Be sure bike is on level surface and secure and cool. 3. Important: Disconnect negative battery cable from battery; refer to owner’s manual. Failure do to so may result in electrical shock, injury, or fire. Secure negative battery cable away from positive side of battery and all other positive voltage sources on bike. 4. Select hidden locations to mount LED Accent Lights to provide best coverage. 5. Remove fuse from fuse holder. 6. Clean mounting locations on both motorcycle and accent lights with 3M promoter, promoter sponge will dry up quickly, place sponge in sealed plastic bag when not in use. Do not touch 3M promoter with bare fingers. 7. Place piece of double sided tape on accent light if needed, lights come pre-taped on back surface. Trim excess off sides with razor blade. Carefully remove backing from double sided tape and place light on selected mounting location. Press firmly and hold for 10 seconds. Repeat for all lights to be mounted on bike. 8. Route wires from accent lights back to central points near battery compartment under seat. Route wires such that they not interfere with normal operation of bike. Cut off any excess wires, strip back insulation as required. 9. Select several locations to secure wires to frame. Secure wires using tie wraps provided. 10. Join all black wires from LEDs into one Cage Clamp Connector #1. Join all Red wires from LEDs into Cage Clamp Con- nector #2, Join all Blue wires from LEDs into Cage Clamp Connector #3, Join all Green wires from LEDs into Cage Clamp Connector #4. 11. Connect Orange wire from the remote control wire harness to the Red Cage Clamp Connector, connect Blue wire from remote control wire harness to Blue Cage Clamp Connector, connect Green wire from remote control wire harness to Green Cage Clamp Connector. Connect White wire from remote control wire harness to Black Cage Clamp Connector. 12. Crimp spade connector on ends of remaining Red and Black wires from Remote Wiring Harness. Heat spade connector with heat gun so that it shrinks around wire. 13. Connect Red Wire to Positive (+) side of battery, and Black Wire to (-) Side of battery. Take necessary precautions when making connection and refer to bike’s owner’s manual. DO NOT allow any tools to touch both positive (+) side of battery and any metal surface on bike as it will cause a short which could result in serious injury and damage to the battery or other electrical circuits.

DRAG SPECIALTIES MINI SPEEDOMETER WITH LED INDICATOR LIGHTS INSTALLATION INSTRUCTIONS

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
1. Place the motorcycle on a level and secure area. Disconnect the battery. 2. Refer to the appropriate factory service manual and remove the OEM speedometer and indicator lights. The indicator lights usually unplug either in the rear of the headlight or under the gas tank area. 3. Mount the new speedometer in the desired location. 4. Locate the OEM wire for the high beam indicator light. Connect it with the blue wire from the wire harness on the speedometer. Connect the blue/black wire from the speedometer to ground. 5. Locate the OEM wire for the gauge illumination (back) lighting. Connect this wire to the orange wire on the speedometer. Connect the black wire on the speedometer to ground. 6. Locate the OEM wires for the turn signals. Usually they are brown and violet wires. NOTE: You will notice only one bulb for the turn signals in the gauge and two wires from the bike to the harness. If you connect both of these wires directly to the yellow wire on the speedometer, this will allow feedback and cause all the signals to flash at once. To prevent this, you will need to add a diode between each OEM turn signal wire and the yellow wire coming from the speedometer. We recommend that you utilize a Dyna tach adapter, Part #D-101, available separately. This tach adapter includes the diodes necessary to allow the turn signal indicator light to operate correctly. Follow the instructions for the tach adapter, substituting the wires from the original wire harness found in step 6 for the two ignition terminals shown in the wire schematic. Hook the white wire on the tach adapter to the yellow wire for the turn signal indicator on the speedometer. If you use the D-101 adapter, skip steps 7-9 and go directly to step 10. 7. Take one of the diodes, making sure to observe the correct polarity, and attach it to the brown turn signal wire on the bike. 8. Take the remaining diode, again making sure to observe the correct polarity, and attach it to the violet turn signal wire on the bike

Incoming search terms:

RIVCO POWERMASTER EFI MODULE Installation AND Tuning Manual

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
Locate the fuel injectors and their connectors on the intake manifolds between the “V” of the engines cylinders. You may remove the fuel tank to gain easy access to the plugs or you can make the connections with the tank on as follows. Remove the rear fuel tank mounting bolt and loosen the front two bolts. Lift the rear of the tank as high as possible (2-3 inches) and place a piece of wood between the tank and frame to hold the tank up. 2. Mounting the POWERMASTER™ EFI Module. While you can mount the module most anywhere it is recommended to mount it under the right hand side cover for easy access when making adjustments. Find a suitable surface to mount the Velcro Adhesive Square supplied. Clean the surface with rubbing alcohol, peel the backing and press firmly in place. Press the Module onto the Velcro. Route the wires with the plugs for the injectors between the frame rails and up toward the injectors with the other wires located on the backbone of the frame. If yours is a model with wires and plugs for the oxygen sensors route these wires downward with the short lead going to the plug on the rear exhaust pipe (about 6″ from the cylinder head) and the longer following along the right frame tube under the engine and forward to the front oxygen sensor and its plug.3. Connect the wires to the injectors under the fuel tank as follows. Unplug the bike’s wire harness from the injectors. Connect the male and female connectors from the injectors and the wire harness to the RIVCO POWERMASTER™ EFI Module. This places it electrically between ECU and the injectors. Repeat this process for each injector. NOTE it does NOT matter which lead goes to which injector.

HARLEY DAVIDSON FLH AND FLT TRAILER HITCH OR RACK LIGHTING WIRE HARNESS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
Remove the seat and locate the tail light plug, this should be attached to the frame with a plastic clip where the fender meets the frame cross member. Unplug the connector and plug in the male and female ends of the supplied wire harness. Route the harness as shown following the other wire looms and then down along the main frame of the trailer hitch or your fender support to the bottom of the rear fender. Secure the harness using the supplied cable ties. Install a plug that matches that of your trailer. The wires in the harness functions/colors are as follows: Black = Ground Brown = Tail Light Red = Brake Light Orange = Left Turn signal Blue = Right Turn signal NOTE: If your trailer has only four (4) wires you will need to use a 5 to 4 wire converter. These are available at most auto parts stores or thru RIVCO Products. NOTE: If your trailer uses more than two (2) incandescent tail light bulbs the use of a trailer wiring isolator is strongly advised as this additional load is too much for the motorcycles wiring to support and may cause damage to the electrical system. Trailer wiring isolators are available although not as common in auto parts stores and are also available thru RIVCO Products. If you are installing both you must first install the 5 to 4 wire converter then the isolator then to the trailer plug.

Incoming search terms:

HONDA GL 18001-RP Illuminator Replacement Lamp Set Installation Instructions

0

Filed Under (Honda) by admin on 23-12-2010

download
1. Remove the plastic caps covering the brake and clutch master cylinder clamp bolts, remove the clamp bolts and clamps. Pull the master cylinders away from the handlebars and let them rest on the fairing storage compartment covers. 2. Using a heat gun or a hair dryer warm up the old lamps one at a time until they are hot to the touch then carefully peel them away from the switch housings. 3. Remove any remaining adhesive from the old lamps left on the housings using rubbing alcohol. Locate the wire harness to the lamp connectors covered with heat shrink tubing. Using a sharp knife carefully cut the heat shrink tubing open lengthwise. Carefully taking caution to not cut the wires, peel the heat shrink tubing open, then away and off the connection. Unplug the lamps from the harness. Replace any of the gold pin connectors on the harness if needed with the new ones supplied. 4. Slide the heat shrink tubing over the gold pins and wire harness ends. Carefully plug the gold pins from the harness onto the lamp connectors (NOTE: the metal connectors on the lamps can break if bent from side to side).Turn on the ignition and verify that all three lamps are working. Slide the heat shrink tubing over the connections and shrink using a heat gun, hair dryer or lighter being careful not to melt the lamp ends. 5. Using your heat gun or hair dryer warm one of the switch housings and the matching lamp so that they are hot to the touch (about 140 degrees). Peel the backing from the lamp, carefully place in position, press firmly onto housing, wrap the tail of the lamp with the wires around the housing and then rub over the entire lamp firmly several times to ensure good adhesion. 6. Reassemble the master cylinders and clamps onto the handlebars being careful not to pinch the wires or lamps.

SUZUKI M109 TURN SIGNAL RELOCATION BAR

0

Filed Under (Suzuki) by admin on 21-12-2010

download
1. Remove the windscreen/headlamp assembly by removing the two (2) 4mm allen screws located on the sides of the windscreen and the two plastic rivets at the top rear (push the center pin inward º” and then pull the rivet out). Pull the windscreen/headlamp forward to gain access to the rear, unplug the headlamp and set aside. 2. Locate the turn signal wire connections and unplug them from the wire harness. On the black connectors lift the tab up to unlock the connector and on the white ones use a small screwdriver inserted into one of the two longer slots and lift the center portion up while pulling the connector apart. Remove the screws which attach the turn signals to the chrome signal mounts located on the bottom of the mounts. Pull the turn signals out from the mounts and set aside. Looking thru the hole in the mount that the turn signals were in you will see a 4mm allen screw on each side, remove these. Remove remaining two (2) 6mm allen screws located on the bottom of the steering head that attach the mounts, remove and set aside. 3. Lay out the new turn signal mounting bar (see photo). Install the signals onto the bar as shown routing the wires thru the bar and out thru the slot in the center. Install the two (2) 6 x 8mm screws supplied and tighten securely. 4. Install the bar/signal assembly onto the steering head using the two (2) 6mm allen screws removed earlier (the brake hose clip should be on the bottom below the signal mount) and tighten securely. 5. Reconnect the turn signal wires (the pale blue/green wire goes to the right signal). Turn the ignition on and test the functions of the signals and running lights. Re-install the windscreen/headlamp assembly being sure to first plug in the headlamp

2000 YAMAHA YZF-R1 SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 27-11-2010

download
CABLE ROUTING SPEC AProperly insert the meter assembly coupler and rubber boot into the meter assembly. BRoute the meter assembly lead through the left side of the headlight housing. CThe speedometer lead with not be tighten. DInstall the headlight relays onto the headlight housing bridge. EConnect to the right front turn signal connectors. FRoute the turn signal leads upper the headlight housing boss. 1 Clutch cable 2 Left handlebar switch lead 3 Starter cable 4 Main switch lead 5 Steering cover EB206000 CABLE ROUTING -21- NRoute the thermo switch/temperature sender sub- wire harness to the outside of the radiator cap. ORoute the right handlebar switch lead behind the throttle cables. Do not cross the throttle cables and the right handlebar switch lead. PRoute the right handlebar switch lead in front of the throttle cables. GFasten the headlight lead with a plastic clamp at white tape mark. HFasten the wire harness to the headlight housing boss with a plastic locking tie. IRoute the headlight lead through the plastic guide. JRoute the throttle cable to the front side of the brake hose. KRoute the clutch cable behind the front fork leg. LMake sure that the horn leads face out. MRoute the throttle cables and right handlebar switch lead between the lower bracket and steering cover. CABLE ROUTING SPEC -22- CRoute the rollover-valve-to-fuel-tank hose to the inside of the fuel hose (California only). DRoute the coolant reservoir breather hose over the timing chain tensioner. EInsert the plastic clip through the hole in the plastic frame panel and then fasten the wire harness and coolant reservoir breather hose with it. FRoute the clutch cable between the radiator bracket and frame and in front of the thermostat assembly breather hose. GRoute the clutch cable to the inside of the radiator inlet hose. HInsert the plastic clamp into the hole in the coolant reservoir’s tab

KTM 125 SX, EXC 200 EXC, XC, XC-W 250 SX, EXC, XC, XC-W 300 EXC, XC, XC-W OWNER'S MANUAL

0

Filed Under (KTM) by admin on 27-11-2010

download
Short circuit button (SX) The short circuit button [1] turns off the engine. When pressing this button, the ignition circuit is short-circuited. Combination switch (EXC) The light switch has 2, respectively 3 switch positions. [A] = Light off (this function is not available in all models) [B] = Low beam on [C] = High beam on You may use button [2] to actuate the horn. The red short circuit button [3] serves to switch off the engine. Leave the switch pressed until the engine stops. Headlamp switch (XC-W) In this model the headlamp is switched on with the pull switch [4] . Flasher switch The flasher switch is a separate unit and is mounted on the left portion of the handlebar. The wire harness is designed in a way that whenever you want to use your bike off-road, you can dismount the entire turn indicator system without affecting the function of the remaining electrical system. Flasher left Flasher right Emergency OFF switch (Australia) The emergency OFF switch [5] is located next to the throttle grip. Primarily designed as safety or emergency OFF switch, it should normally not be in its activated state. In this position, the ignition circuit is shorted; if the engine is running, it will stall immediately, if it is at standstill, it will not start. In this position, the ignition circuit is enabled; the engine should start. 1 2 3 5 A B C 4
ENGLISH 12 Filler cap To open it: turn filler cap counter-clockwise. To close it: put filler cap back on and tighten it by turning it clockwise. Install tank breather hose [1] without kinks. Filler cap (XC, XC-W) To open the filler cap: Turn the filler cap 45 ° counter-clockwise. To close the filler cap: Put the filler cap on and turn it 45 ° clockwise. Fuel tap OFF In this position the fuel tap is closed. No fuel can flow to the carbure- tor. ON During operation the twist grip must be turned to ON. This means that the fuel can flow to the carburetor. With the twist grip in this position the tank will be emptied until only the reserve is left. RES The reserve tank cannot be tapped until the rotating handle is turned to the RES position. Fill the tank as soon as possible and remember to turn the rotating handle back to the ON position so that you will have backup fuel next time, too. Reserve of the 8.5 l tank . . . . . . 1.3 l (0.32 USgallons) Reserve of the 10 l tank . . . . . .1.7 l (0.45 USgallons

Incoming search terms:

Incoming search terms: