KAWASAKI VULCAN 1600 / NOMAD 1600 INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Remove seat and fuel tank. Consult service manual for proper removal of tank. 2. Remove left side cover and loosen the four bolts inside. Route the two 6-pin connectors between the side cover and frame as shown by the dotted line. Tighten the four bolts. (Fig 1) 3. Route 6-pin connectors under frame and up left side of engine. (Fig 2) 4. Locate the 6-pin connector next to the ignition coil. Disconnect and connect the Fuelpak 6-pin connectors in-line on the stock connector. (Fig 3) 5. Route single black wire to the front of engine and down to the horn. (Fig 4) 6. Disconnect the factory black/white wire from horn. Plug Fuelpak into horn and plug Fuelpak black/white wire to Fuelpak connector. Be sure Fuelpak connector cannot short to frame or radiator. 7. Route black and green wires to battery negative. 8. Attach Fuelpak to Fuelpak harness and mount in left side cover. (Fig 5a 49 State) (Fig 5b Caliornia Models) 9. Before reassembling the bike, make sure handlebar switch is in the engine off position and turn the key on. Fuelpak should light up. Sound the horn. If Fuelpak turns off when the horn is sounded, recheck the black wire connection on the horn and that it is connected to the correct wire from the factory harness. 10. Use supplied zip ties to hold Fuelpak wire harness away from engine. 11. Follow the service manual to reinstall the gas tank

Incoming search terms:

Kawasaki Sxi/ SXR Ignition twin cylinder Jet Ski ignition Installation Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Remove electronics enclosure from its mounting location. 2. Unplug and remove the OEM ignition. 3. Set the programming switches on the T3 to your settings. 4. Install the T3 Ignition in the same location in the electronics enclosure. 5. Test the T3 Ignition. 6. Close the electronics enclosure cover plate and mount the module in the PWC. Installation Remove electronics enclosure from its Mounting Location 1. Using a 10mm socket remove the mounting bolts on each side of the electronics enclosure. 2. Remove the enclosure cover and set aside the screws, 2 mounting flanges, ‘O” ring, and enclosure top. Unplug and Remove the OEM Ignition 1. Using 10mm socket, remove bolts from each side of the OEM ignition. Lift out the ignition and unplug all connectors attached to the OEM ignition. Now remove the protective metal plate that was under the ignition and two 3/16″ thick washers under that plate. 2. On 2004 models and newer remove the wire harness for the two black connectors just unplugged from the OEM ignition. Trace each wire from each black connector back to in-line connectors and separate each of these connectors. Set the two harnesses aside. Install the T3 Ignition in the Electronics Enclosure 1. Install the T3 ignition into the mounting bracket supplied with your T3. Slide the end of the ignition module under the lip at the rear of the bracket an press the wire end of the ignition firmly into the bracket. Attach the keeper bracket using two 5mm bolts supplied. Place the ignition/bracket in the location where the OEM ignition and metal plate were removed. Secure the ignition in place with the supplied bolts

Incoming search terms:

2008 KTM 250 SX-F 250 XC-F, XCF-W 250 EXC-F, EXC-F SIX DAYS INSTALLATION MANUAL

0

Filed Under (KTM) by admin on 22-10-2010

download
Hand brake lever The hand brake lever [1] is mounted on the handlebars on the right and actuates the front wheel brake. The adjusting screw [A] can be used to change the basic position of the hand brake lever (see “Maintenance”). 1 A Short circuit button The short circuit button [2] turns off the engine. When pressing this button, the ignition circuit is short-circuited. 2 Headlamp switch (XCF-W) In this model the headlamp is switched on with the pull switch [5] . 5 Flasher switch The flasher switch is a separate unit and is mounted on the left portion of the handlebar. The wire harness is designed in a way that whenever you want to use your bike off-road, you can dismount the entire turn indicator system without affecting the function of the remaining electrical system. Flasher left Flasher right
OPERATION INSTRUMENTS » ENGLISH 7 1 2 3 4 5 Starter button Pushing the red starter button [1] will actuate the E-starter. Emergency OFF switch (EXC-F Australia) The red emergency-OFF switch [2] is arranged adjacent to the throttle grip. In this position, the E-starter is operational and the engine can be started. In this position, the E-starter and ignition circuits are interrupted.The E-starter cannot be actuated, and the engine will not start, not even if you attempt to start it with the kickstarter. Pushing the black starter button [3] will actuate the E-starter. Indicator lamps The green control lamp [4] flashes in the same rhythm as the flashing indicator when the indicator is working. The blue control lamp [5] lights up when the high beam is on. TEST All of the display segments briefly light up for the display function test. Electronic speedometer The display in the electronic speedometer is activated as soon as you press a button on the speedometer or an impulse is received from the wheel sensor. The display lights up when the engine is running. The display is cleared if no button is pressed for 1 minute or no impulse is received from the wheel sensor. The button is used to change between display modes. The + and – buttons are used to control various functions

Incoming search terms:

Incoming search terms: