Ktm 950 SMR Installation and Removal Manual

0

Filed Under (KTM) by admin on 27-01-2012

download
Be sure the triple clamp in your kit has a part # 3012R- 27 -6-0208 on the bottom side. This is very important. 2. Warning: Once the triple clamp is loose, the forks can roll away from the bike . Block it up properly to start with. 3. Block the front tire securely before removing the top triple clamp, so the tire cannot move forward. It’s best to tie the forks up to something above you, like the rafters, using tie downs, or a tie down from the front axle up and over the frame backbone and then underneath the lower triple clamp. Once the forks start to come off while working, it’s extremely difficult to get them back together without help. Block the back wheel up also, so it puts pressure on the front end, forcing it to stay in position. Spend the time setting this up correctly and your installation will go easier. 4. This kit requires removal of the headless “Security” bolts that hold the key switch in place. These bolts will need to be drilled out in order to remove them, pictures below. Removal is fairly easy, if you follow these instructions. 5. Examine all the wire and cable routing before removal and make notes of where everything goes. 6. Remove 2 bolts that hold the headlight shroud in place. Be careful not to lose the small bushings that fall out easily. 7. Follow the wire from the ignition switch to the wire loom in the headlight shroud and unplug it. There is no locking tab on this plug so you can usually undo it without having to disassemble the wiring. 8. Remove the 4 bolts that hold your bars tight and lay the bars forward out of the way (Bungie or tie to the front of bike). 9. Be sure the front end is securely blocked or tied to something above the bike. Remove the top triple clamp, taking note of how tight the 27mm main nut is, so you can re-tighten to the exact tension for the bearing. The main nut merely provides the correct tension on the head tube bearing, so the tension is critical. The nut will NOT be tight coming off. Once the fork and triple clamp pinch bolts are loose, the main nut can be removed. It’s difficult to get a wrench on the main nut. We were able to sneak the stock KTM axle wrench in there, otherwise, you may have to loosen the lower bar perches using an 8mm Allen wrench and a 17mm socket for the underside nuts. Once the main nut is off, lift the triple clamp off carefully , trying not to disturb the blocked-front-wheel. A rubber mallot is helpful here

SMALL COOLER RACK LIGHTING SYSTEM INSTALLATION MANUAL

0

Filed Under (Tips and Review) by admin on 29-12-2010

download
1. Using the nuts supplied, bolt the lighting system to the rack (on some earlier production models the holes may be off slightly and require that you drill the holes in the rack larger for alignment). 2. Using a side cutting pliers, trim away the corner of the metal grating and route the wire loom thru and out the bottom of the rack as shown. Route the loom along the bottom of the rack to where the plug on the motorcycle is or will be and secure it to the rack using the cable ties supplied. 3. Cut the wires and loom to the desired length to connect to the plug on the motorcycle. Connect the wires from the loom to your mating connector (not supplied) using the wire color code shown below. If you do not have a plug on the motorcycle you will need to purchase a mating male and female five pin or wire connector set. You may also use a six pin connector set and leave one pin unused as these are more readily available. RIVCO offers a six wire molded connector set with 60″ of wire #TWC002 or a waterproof six pin connector set with dust cap #TWC00

TRIUMPH AMERICA AND SPEEDMASTER FRONT TURN SIGNAL RELOCATORS

0

Filed Under (Triumph) by admin on 29-12-2010

download
1. Remove the front turn signals as follows. The turn signal wire plugs are located inside the handlebar switch housings. Remove the two Phillips screws located on the forward facing side of the switch housing, remove the covers, unplug the turn signals and reassemble the switch housings. Unbolt the signals from their black mounting brackets, remove the brackets from the bottom side of the switch housings, reinstall the nuts and tighten securely. 2. Disassemble the two halves of the turn signal mounting clamps supplied, place the M6 X 25mm button head screws thru the hole in the side of the clamp from the inside, place the spacers supplied over the screw threads. Screw the clamps and spacers onto the turn signals. Hold the signal/clamp assemblies up to the front fork, position the signals so that the housing/lens seam is vertical and straight, carefully remove the assemblies from the forks and tighten the screws securely. Install the signal/clamps onto the forks, set to the desired height and angle and tighten the clamp screws securely. 3. Using a sharp knife slit the black wire loom from the turn signal plug back 7″. Pull the turn signal wires and plugs out from the loom. Fold the wires along the loom going down towards the headlight. Leave 2-3″ of the wire next to the plug exposed and neatly tape the rest of the wire to the loom and the loom closed back up to the handlebar switch. 4. Connect the signal wires to the plugs from the wire loom. Using the cable ties supplied tie up any loose or unconcealed wire and the plugs.

Triumph Speed Triple Installation Instructions

0

Filed Under (Triumph) by admin on 30-10-2010

download
1. Remove OEM Tail Unit from Motorcycle (ref: underside four socket head bolts). 2. Disconnect all electrical connections (ref: Turn indicators & License light). 3. Remove Turn indicators from OEM Tail unit and install on to Skyking Products License Plate Relocation Assembly using OEM hardware. 4. Remove License light from OEM Tail unit and install on to Skyking Products License Plate Relocation Assembly using OEM hardware. 5. Reconnect all electrical connections. Install wire loom for connector protection and secure with tie wraps . (ref: Turn indicators & License light). 6. Install Skyking Products License Plate Relocation Assembly using OEM hardware. 7. Double check all hardware and electrical are secure. 8. Check proper operation of Turn indicators and license light. 9. Test ride and final check proper operation of Turn indicators and license light.

2008-2009 Kawasaki Concours Bar Adapters Installation Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1.) Three minor alterations need to be made before the stock bars can be unbolted from the top triple clamp. These alterations will provide the necessary slack in the clutch hydraulic line, front brake hydraulic line and the two large wire looms running up to the left and right handlebar control housings. a.) Unbolt the metal wire guide that holds the clutch hydraulic line in place on the left side of the steering head. Flip the guide end for end keeping the offset to the outside (left) and place the clutch hydraulic line into the offset. Reinstall the two 6mm bolts (10mm heads) and torque to 7 ft. lbs. Make sure the clutch hydraulic line sits on top of the upper fairing mount bolt. See photo # 1. b.) Locate the left and right wire loom plastic guides mounted to the lower triple clamp. See photo # 2 (left side shown). Pull up on the wire loom with one hand while you feed the loom through the plastic guide with your other hand. About ½” extra slack should be fine. If the plastic guide pops open, simply re-gather the looms together and snap the guide back together. Some adjustment may be necessary after install. c.) CAUTION: Cover the fuel tank and the upper fairing sides with a towel / rag, etc. Carefully loosen the front brake banjo bolt located at the bottom of the front brake master cylinder just enough to rotate the line forward (roughly ½”). See photo # 3. This banjo bolt will loosen with a sudden snap and may move (loosen) more than you need. Keep your hands away from the brake lever as this may force brake fluid out around the banjo fitting. Move your hydraulic line as shown in photo # 3 and re-tighten the banjo bolt to 16 ft. lbs.