1999-2001 Harley-Davidson Twin Cam 88 FI Controller Installation MANUAL

0

Filed Under (Harley Davidson) by admin on 25-03-2012

download
Remove the seat. Remove or raise the fuel tank. The tank needs to be raised enough to give access to the fuel injectors and TPS wires. Unplug the front injector. On the FI Controller, there are 2 pairs of injector connectors. Plug the pair with the orange wires into the front cylinder injector harness and front cylinder injector. Repeat this using the other connector pair and the rear cylinder injector. Locate the TPS connector behind the throttle body. STEP 1 STEP3 STEP2 Installation Part# DFCH-2 2 Rear Cylinder Injector Front Cylinder Injector TPS Connector STEP 3 STEP 2 STEP1 Unplug the connector from the TPS. Crimp the wire tap onto the wire that is grey with a purple stripe. This wire should be in position “C” on the connector. Plug the grey wire from the FI Controller into the wire tap. Run the wiring harness for the FI Controller from the engine to the seat. Make sure that it will not get damaged when you reinstall the tank. Use one of the wire ties to tie the wires to the frame, away from the cylinder head. Place the FI Controller where you plan on mounting it permanently. In most cases, this will be under the seat. Connect the ground lug (black wire) to a grounding point on the bike. Use the Velcro tape to mount the FI Controller in position. Use alcohol swab to clean mounting surface prior to attaching Velcro. Reinstall fuel tank and seat. STEP 4 STEP 6 STEP 5 STEP4 STEP6 STEP5 Installation Part# DFCH-2 3 FI Controller
For Tech Support: 800.928.3962 Controls The FI Controller is preprogrammed with 4 base fuel curves. The curves are selected using the switch labeled BASE. These curves adjust fuel delivery based on throttle position and RPM, providing the right amount of fuel under all conditions. The 4 fuel curves correspond to varying levels of performance modifications. The levels of modification are broken down into the following groups. Base Curve 1 – Stock or basic modifications. This includes slip on exhausts, intakes, air boxes, and air filters. It will also work for headers or full exhaust systems. Base Curve 2 – Motor upgrades. This includes cams, 95 ci motors. Base Curve 3 – More extensive motor upgrades. This includes 103 ci motors, cams, ported heads

Honda GL 1800 FOG LAMP INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 24-11-2011

download
Disconnect the negative cable from the battery before installing this accessory. • To prevent scalding, allow the engine and cooling system to cool before installing this accessory. • The memories of the tripmeter, clock, radio andbsuspension system will be erased when you disconnect the battery. Reset the memories after reconnecting the battery. • Tighten the screws, bolts and nuts securely. • Trim the excess ends off the wire ties after attaching them to the wire harnesses. Do not allow the cut part of the wire tie to interfere with another harness or brake pipe. Using cutting pliers, cut out the marked areas from the front lower cowl. Finish the edges of the holes smooth and flat with a file. 1. Disconnect the negative cable from the battery. 2. Remove the front lower cowl and bolts as described in the Service Manual.

HONDA GL1800 Chrome Mesh Grill Accents Installation Manual

0

Filed Under (Honda) by admin on 04-03-2011

download
NOTE: Read instructions thoroughly before installing. Work one side at a time. 1. Place bike on center stand. 2. Thoroughly clean outside surface of the chrome air intake area where inserts will be install with rubbing alcohol pads- provided. 3. Using the silicone provided, run a bead of silicone as shown in figure 1 or on the original side fairing in the same manner. 4. Carefully place insert mesh into place. 5. Press the accent into place. 6. Using two wire ties, secure the chrome accent by wrapping the wire ties through the original radiator grill as shown in figure 2. Note: You may want to use masking tape or a soft material to protect the chrome or painted surface while placing the piece on the bike. 7. Repeat on the other side. 8. Wait at least 12 hours before removing wire ties.

HONDA GL1800 DASH DOOR ACCENTS INSTALLATION MANUAL

0

Filed Under (Honda) by admin on 28-02-2011

download
Note: Read instructions thoroughly before installing. 1. Place bike on center stand. 2. Run a bean of silicone (provided) on the inside edge of one of the Dash Door Accents. 3. Place the accent over the pocket and secure with wire ties (provided). Repeat on the other side. 4. Run a bead of silicone on the underside of the door latch accent and set in place. 5. Allow time for the silicone to set (at least overnight). HONDA GL1800 DASH DOOR ACCENTS INSTALLATION MANUAL