HARLEY DAVIDSON FRONT AND REAR FENDER TIP TRIM INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-03-2011

download
Installation GENERAL The original equipment (stock) fender tip lamp assemblies must be removed and the wire(s) must be unplugged or removed as specified in the following instructions. FRONT FENDER TIP REMOVAL OF STOCK FRONT FENDER TIP LAMP ON 1994 AND LATER FLT MODELS 1. Refer to the applicable FLT Service Manual. Remove headlamp assembly with housing. 2. Locate the 3-place connector [32 in wiring diagram] through which 12vdc and electrical ground are connected to the fender tip lamp assembly. The connector locations are as follows: FLTC Ultra: Under fuse and circuit breaker block FLHT/C/C-U: On bottom of left outer fairing bracket FLHR: On left front above air suspension valve NOTE Before disassembling the connector in the next step, refer to the applicable wiring diagram and check wire colors and connections to assure that connector [32] has been located. 3. Refer to the “DEUTSCH ELECTRICAL CONNECTOR” section in the FLT Service Manual and remove the leads, connected to the fender tip lamp, from the socket half, connector [32B]. 4. Insert a small screwdriver blade in rectangular slot at top center of fender tip lamp lens and gently pry lens from lamp. 5. Remove two screws and nuts that fasten fender tip lamp assembly to front fender. Gently remove the lamp assembly taking care not to damage wires connected to lamp assembly. 6. Reach under left side of fender and gently pull wires through rear hole in left side of fender and then through clips on left side of fender and finally through front hole and out of trim strip. REMOVAL OF STOCK FRONT FENDER TIP LAMP ON 1993 AND EARLIER FLT MODELS, FLSTC AND FLSTN 1. Insert a small screwdriver blade in rectangular slot at top center of fender tip lamp lens and gently pry lens from lamp. 2. Remove two screws and nuts that fasten fender tip lamp assembly to front fender. Gently remove the lamp assembly taking care not to damage wire connected to lamp assembly. 3. Unplug wire connector located about 3 in. from lamp assembly. Cover the socket half of connector (connected to motorcycle wiring) with electrical tape. INSTALLING FRONT FENDER TIP TRIM FROM KIT-ALL MODELS 1. Position fender tip trim over holes in fender and guide outer ends of fender tip trim into trim strips on sides of fender. 2. Insert studs on fender tip trim through holes in fender and secure with locknuts included in kit. Tighten locknuts to 6 in-lbs . REAR FENDER TIP REMOVAL OF STOCK REAR FENDER TIP LAMP ON ALL MODELS Follow steps 1 through 3 given above for “1993 AND EARLIER FLT MODELS, FLSTC & FLSTN” INSTALLING REAR FENDER TIP TRIM FROM KIT-ALL MODELS 1. Position fender tip trim over holes in rear fender. 2. Insert studs on fender tip trim through holes in fender and secure with locknuts included in kit. Tighten locknuts to 6 in-lbs

Incoming search terms:

VICTORY HAMMER, KINGPIN, VEGAS AND JACKPOT ELECTRIC HORN INSTALLATION INSTRUCTIONS

0

Filed Under (Victory) by admin on 29-01-2011

download
1. Remove the left and right plastic side covers and the seat (two allen bolts located below the sides of the seat). Unplug and remove the stock horn (located over the oil cooler). Connect the female ends of the jacketed two wire cable supplied to the original horn wires. Route the other end of the cable up over the engine and back to where the relay will mount as shown in photo (1). 2. Using the relay supplied with this kit and the wiring diagram provided with the horn set, identify the terminals of the relay (there are very small numbers next to each of the terminal). Connect the two (2) wires from the cable to terminals #85 & 86 on the relay. Locate the fuse holder wire assembly supplied and connect the blade terminal to the relay terminal #87 or #30. Connect the other end of the fuse wire to the battery positive terminal (+). 3. Working under the left side of the motorcycle, refer to photo (2) and install the black bracket supplied as shown onto the engine mount. Locate the four thin flat brackets and two (2) 6mm nuts supplied with the horn set and two lock washers supplied with the kit. Bolt two (2) of the brackets to each of the horns using a lock washer and 6mm nut on each and make them snug. Using the remaining 6 x 12mm bolt, nut and lock washer install the horns onto the black bracket and align as shown in photo (3). Adjust the horn location so that they are free to vibrate and do not come in contact with other parts of the motorcycle then tighten all three 6mmm bolts securely. 4. Using the two remaining wire assembles supplied, connect the larger terminals with double wires to one of the horns and the terminals with the single wire to the other horn. Route these wires up thru the frame to the relay. Connect the wire with the female blade connector to the relay terminal #30 or #87. Connect the ring terminal to the battery negative (-) terminal
or any 6m bolt on the frame. Turn on the ignition and test the horns. Secure the relay to the frame or other wiring and all loose wires using the cable ties supplied. Replace the seat and side covers

Incoming search terms: