KAWASAKI VULCAN 2000 POWERSHOTS EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 23-12-2010

download
STOCK EXHAUST SYSTEM REMOVAL 1. Remove right side frame cover. 2. If motorcycle is oxygen sensor equipped, remove passenger seat. Remove two bolts securing operator seat and set seat aside. Locate and unplug oxygen sensor connector from wiring harness (Figure 1).(Note wire routing for reassembly). 3. Remove right side floorboard assembly held in place by two bolts (Figure 2). 4. Remove exhaust port flange nuts. 5. Remove flange bolts securing rear muffler to exhaust system mounting bracket. 6. Remove complete exhaust system. Start by removing front head pipe from exhaust port (assistance may be required). Page 1of 4 K400IN Rev. 1.1 KAWASAKI VULCAN 2000 POWERSHOTS EXHAUST SYSTEM Part #18311 Tools required for installations 6mm Allen wrench 8mm 12mm 14mm sockets 3/8″ Ratchet & Extensions 19mm Wrench 9/16 Wrench Brake bleeder & fluid
7. Check condition of stock exhaust gaskets. Replace if damaged or worn. 8. Remove plastic hose clamp securing rear brake hose to swingarm.Save for re-use. 9. Remove brake hose banjo bolt from rear caliper. 10. Slide hose out of loops in swingarm. 11. Remove three bolts holding stock exhaust mounting bracket and slide bracket off end of brake hose. 12. Slide brake hose through loop on new bracket (stamped 357-P) and install to the original mounting bracket location, using three 8mm x 16mm Allen bolts (supplied) (Figure 3). 13. Check condition of sealing washers on banjo bolt and replace if damaged or worn. 14. Slide brake hose through loops on swingarm and reconnect brake hose to caliper. 15. Reinstall plastic clip onto swingarm. 16. Brake system must be bled or brake will not operate correctly.

Incoming search terms:

2003-2004 HONDA GL 1800/A Frame Weld Safety Recall

0

Filed Under (Honda) by admin on 15-12-2010

download
there is no punch mark on the VIN plate as specified in this Service Bulletin, proceed to the REPAIR PROCEDURE section of this Service Bulletin. IMPORTANT: Due to the complexity of this campaign it is imperative that you check iN and your Dealer Responsibility Report before you begin repairs. If iN or your Dealer Responsibility Report indicate the Safety Recall has been performed, but you confirm the unit is not punched and the repair has actually been done (by inspecting the weld), please contact the Warranty HelpLine at (800) 421-1900, option 7. IMPORTANT: For complete Dealer and Welder Repair procedures, refer to the following items: • 2002-2003 GL1800/A Frame Weld Safety Recall Dealer Booklet (S0510)  Frame Weld Inspection Chart (S0516) You MUST provide your TIG welder with the following items:  2002-2003 GL1800/A Frame Weld Safety Recall Welding Manual (S0511)  2002-2003 GL1800/A Frame Weld Safety Recall Cracked Weld Repair Manual (S0515) Welding Template Box (S0512) All of the above items were shipped to you with Service Bulletin GL1800 #14. If you need additional copies of these materials, you may order them from Resolve at (440) 572-0725. For your reference, a brief repair procedure overview is provided below. DISASSEMBLY OVERVIEW You will be removing the following components from the vehicle as instructed in the Dealer Booklet : Handlebar weights Rear view mirrors Swingarm pivot covers Rider foot pegs Seat Side covers/Engine side covers Fairing pockets Fairing molding Meter panel Top shelter Battery Fuel tank Main wiring harness ground Front lower fairing Front exhaust pipe protector Muffler/exhaust pipe Antenna Whip(s) Coolant reserve tank Center stand NOTE: You will need to remove any accessories that may contact the ground during the Welding and Re-assembly procedures. IMPORTANT: Before you send the motorcycle to the welder, you MUST check for lower crossmember frame weld cracks.  If your inspection reveals no cracks in or on either the Left or Right lower cross- member frame welds, proceed to the REPAIR PROCEDURE OVERVIEW section of this Service Bulletin.  If your inspection identifies a crack or cracks in or on either the Left or Right lower crossmember frame welds, perform the following procedure: Place the grinding template (S0512) on the crossmember. Using a suitable felt marker, draw a line on the weld with the crack, drawing the line along the entire edge of the the template (this line will be 89 mm long). If the crack falls within the length of this line (89 mm) , prepare the motorcycle for welding per the Dealer Procedures and advise the welder to use the Cracked Weld Repair Manual (S0515). After the bike has returned from the welder, prepare the frame and re-assemble the motorcycle per the Dealer Procedures . Then, proceed

Incoming search terms:

Introducing the New BMW R 1200 RT-P

0

Filed Under (BMW) by admin on 15-12-2010

download
The new R 1200 RT-P features a completely new LED emergency lighting concept developed by BMW and Code 3 PSE. The new system combines all currently desired emergency lighting into optimally focused compact LED light modules. These modules accommodate an additional 45 degree front LED module that blankets the front quadrants in emergency light. Together with an integrated wiring harness and programmable flash control module, the new system can provide any current flashing sequence / switching combination through settings on the programmable flasher. Example: If the motor will be used in California, program the flasher for steady-burn left front LED light, with no change in the LED light or the wiring. If the motor is sold or operated in a different venue later, change the program flasher for 49 state operation. The rear light module combines rear and side facing LED emergency lights, together with rear-facing brake/tail LED and side turn signal LED lights. Additional rear facing LED emergency lights can be installed and powered in conjunction with the rear facing lights, or controlled by photo- eye to disable the lights during the dark to reduce glare at night / low light situations. The programmable flasher can provide 12 flash patterns, with wiring splitting the motor between left and right side for alternating flash patterns. Light sequencing begins with rear, programmable rear and front side lights, as well as front and 45 degree front lights. A rear cancel switch allows riders to disable the rear lights while retaining the side and front lights – usually used for protective service details. The programmable flasher also provides for a primary and secondary flash pattern, so during code 3 operation, the emergency lights will display the primary pattern until the siren is activated, at which time the flasher changes to the alternative pattern for 7 seconds after each siren tone change. This feature known as InterClear provides a visual and audible alert to those nearby

Incoming search terms:

2002-2003 Honda GL1800/ A Frame Weld REPAIR PROCEDURE OVERVIEW

0

Filed Under (Honda) by admin on 14-12-2010

download
If your inspection identifies a crack or cracks in or on either Left or Right lower crossmember frame welds, STOP – call your DSM or TechLine for further instructions. • If your inspection reveals no cracks, proceed to REPAIR PROCEDURE. NOTE: Verification of repair can also be found in the Dealer Responsibility Report and on the Honda Interactive Network (iN). If you have any questions about verification, please contact TechLine before proceeding. IMPORTANT: For complete Dealer and Welder Repair procedures, refer to the following items: • 2002-2003 GL1800/A Frame Weld Safety Recall Dealer Booklet (S0510) • Frame Weld Inspection Chart (S0513) You MUST provide your TIG welder with the following items: • 2002-2003 GL1800/A Frame Weld Safety Recall Welding Manual (S0511) • Welding Template Box (S0512) All of the above items were shipped to you with this Service Bulletin. If you need additional copies of the Dealer Booklet , Welding Manual , Welding Template Box , or Frame Weld Inspection Chart , you may order them at no cost from DDS at (440) 572-0725. For your reference, a brief repair procedure overview is provided below. Disassembly Overview You will be removing the following components from the vehicle as instructed in the Dealer Booklet : • Handlebar weights • Rear view mirrors • Swingarm pivot covers • Rider foot pegs • Seat • Side covers/Engine side covers • Fairing pockets • Fairing molding • Meter panel • Top shelter • Battery • Fuel tank • Main wiring harness ground • Front lower fairing • Front exhaust pipe protector • Muffler/exhaust pipe • Antenna Whip(s) • Coolant reserve tank • Center stand NOTE: You will need to remove any accessories that may contact the ground during the Welding and Re-assembly procedures. IMPORTANT: You MUST cover the following with RED duct tape for welder identification pur- poses: • Negative (-) and positive (+) battery cables • Fuel return hose end • Fuel feed hose end • Main wiring harness ground • Alternator • Exhaust ports Welding Overview A qualified TIG welder will weld the frame following the procedures in the 2002-2003 GL1800/A Frame Weld Safety Recall Welding Manual . Re-assembly Overview You will be inspecting the new TIG welds, painting the frame, and re-assembling the vehicle as detailed in the Dealer Booklet and Frame Weld Inspection Chart (S0513)

Incoming search terms:

Victory Lowering Kit INSTALLATION INSTRUCTIONS

0

Filed Under (Victory) by admin on 04-12-2010

download
This kit was designed for use with stock length shocks ONLY! We do not recommend using shorter than stock length shocks with this kit. We highly recommend that your dealer install this kit. If you do not have access to a stand capable of securely supporting/lifting the motorcycle as well as tools capable of removing/replacing the suspension links, please allow your dealer to assist you. INSTALLATION INSTRUCTIONS 1. Support motorcycle securely so that rear wheel is off the ground. 2. Remove #19, #21, #22, & #23. Refer to Fig.1 Secure & support the swing arm before removal of these parts. 3. Re-install #19, #21, & #22 using our kit in place of #23. 4. Torque fasteners to 35 ft. lbs. 5. Check for proper clearance at fender & belt guard. Please note that excessive load or other riding/road conditions could cause the bike to bottom out and potentially cause the tire to come into contact with the rear wiring harness. Adjust the pre-load of the shock per the owner’s manual or relocate the wiring harness as necessary

2008 SUZUKI GSX 1300 RK IGNITION SWITCH INSPECTION/ REPLACEMENT

0

Filed Under (Suzuki) by admin on 29-11-2010

download
INSPECT ROUTING 1. Remove the upper and lower meter panels (refer to Service Manual page 9D-15). 2. Check if the ignition switch lead wire is clamped and routed correctly. Incorrect positions are shown in Figures 1 and 2. Correct routing and clamping is shown in Figures 3 and 4 on page 5. REROUTING 1. Reroute the ignition switch lead wire correctly (Figure 3 and Figure 4). The ignition switch lead wire should not be covered by the other wire harnesses. 2. Turn the handlebars back and forth to verify that the steering operates smoothly and the wiring harness does not become kinked or pinched. 3. Proceed to PUNCH MARK AT VIN on page 8. from the motorcycle (refer to Service Manual page 1H-12). Remove the two black plastic covers to access the cylinder cap mounting bolts (Figure 5). Note: The black plastic covers will not be reused. Secure the mount area (bottom) of the ignition switch in a vise (Figure 6). NOTE: Turn the ignition switch to the OFF position and remove the key from the ignition switch before disassembling the switch. Remove the two “break-off” screws from the ignition switch using the special screwdriver. Set the stepped end of the sleeve on the special screwdriver facing toward the “break-off” screws (Figure 7). Strike the special screwdriver 5 to 7 times with a hammer to produce a deep enough groove on the screw head for the screwdriver to work properly (Figure 6). Pay attention not to hit other parts with the hammer. Turn to remove the “break-off” screws in a counterclockwise direction. If the groove becomes damaged, make another groove at a 90o angle to the original groove. Remove the ignition switch from the vise and hold it upright over the workbench and carefully remove the cylinder cap (Figure 8). NOTE: Pay close attention to the order and orientation of the ignition switch parts during disassembly. REPLACEMENT OF IGNITION SWITCH (Customer Sold Units/Dealer Demo Units- Only If Inspection Shows Incorrect Routing And Unit Has Been Ridden) New Ignition Switch Disassembly 2.

Oil Pressure Gauge Set Installation

0

Filed Under (Tips and Review) by admin on 27-11-2010

download
7. See Figure 3-4 . Assemble banjo bolt (3), washer (4), OIL PRESSURE GAUGE (1) banjo fitting and second washer onto adapter and tighten snugly. 8. Temporarily secure oil pressure gauge and hose to motorcycle frame with cable straps. Make sure gauge and hose assembly do not interfere with normal operation of the vehicle. Start engine and ride motorcycle at least 20 miles (32 km) at or above 50 mph (80 km/h) to allow engine to reach operating temperature. a. At 2500 RPM, oil pressure will vary from 10-17 psi (69-117 kN/m2). b. At idle speed (950-1050 RPM), oil pressure will vary from 7-12 psi (48-83 kN/m2). NOTE For an accurate reading, engine oil should be at normal operating temperature: 230°F (110°C). 9. Stop engine. Remove OIL PRESSURE GAUGE assembly from oil pressure indicator lamp switch mounting hole in crankcase. Cut cable straps that you installed in step 8. above, and remove banjo bolt, gauge assembly, washers and adapter from vehicle. 10. See Figure 3-2 . Coat threads of oil pressure switch (2) with LOCTITE 565 HIGH PERFORMANCE PIPE SEALANT with TEFLON. Reinstall oil pressure switch. Using OIL PRESSURE SENDING UNIT WRENCH, tighten switch snugly. DO NOT OVERTIGHTEN. 11. Plug in connector [120] (3) by pushing elbow connector straight up onto stud on oil pressure switch. 12. Install voltage regulator caddy and attach DC output connector and neutral switch wiring harness to caddy. See 7.28 MAIN WIRING HARNESS . NOTE If an appreciable amount of oil leaked out when oil pressure switch was removed, it will have to be replaced with fresh oil. 13. Check oil level in oil tank. See 1.5 ENGINE OIL AND FILTER . Top off oil level if necessary. 14. Start engine and test oil pressure switch for proper operation. Check oil pressure switch for leaks.

Incoming search terms:

HONDA Ground Effects Installation Instructions

0

Filed Under (Honda) by admin on 10-11-2010

download
Wiring Installation: 1. Remove the four M8x1.25 socket head cap screws from the seat and remove the passenger handles and seat. 2. Remove both rear side covers, and right front side cover. 3. Remove the two M3 Phillips head screws and two trim clips from the right front storage pocket. 4. Place the three relays of the Ground Effects Ground Effects Ground Effects Ground Effects wiring harness underneath the relay box. 2001 2001 2001 2001 — – 2005 MODELS 2005 MODELS 2005 MODELS 2005 MODELS Route the long end of harness (blue wire and orange wire), behind the fuel tank to the brake lines. The shorter section of the harness will end at the brake lines. Continue along the brake lines to the main harness of the motorcycle to the shelter, then up through the shelter to the pocket area. 5. Locate the harness connectors under the pocket. Go to step 6. 2006 & NEWER MODELS 2006 & NEWER MODELS 2006 & NEWER MODELS 2006 & NEWER MODELS Route the long end of harness (blue wire and orange wire), under the relay box and connect to the Positions Relay. 6. Connect the orange wire to the orange wire with white tracer using a scotch-lok connector. Connect the blue wire to the light blue wire with white tracer using a scotch-lok connector. 7. Route the red and white wires behind the fuel tank, along the left side wiring harness to the fuse box. 8. Connect the RED wire with eyelet connector attached, to the positive side of the accessory terminal in the fuse box. 9. Connect the WHITE wire to the negative battery terminal. 10. Connect the brown wire with white tracer to the brown wire with white tracer (tail relay in relay box) using a scotch-lok connector. 11. Route the orange wire with black tracer and the white wire behind the fuel tank, with at least 6 inches of wire left hanging below the bike. 12. Reinstall the right fairing pocket with the two M3 Phillips head screws and two trim clips. 13. Replace the right front side cover and the right and left rear side covers. 14. Replace the seat and passenger grip handles with the four M8 x 1.25 socket head cap screws

Incoming search terms:

Yamaha Road Star Warrior Fuel Injected Models INSTALLATION INSTRUCTIONS

0

Filed Under (Yamaha) by admin on 08-11-2010

download
1. Remove seat and fuel tank. 2. Remove airbox and left airbox cover. We highly recommend you consult the factory service manual for proper removal of airbox. 3. Route wiring harness under frame bracket towards airbox. (Fig 1) 4. Unplug stock black connector for fuel injectors. (Fig 2) 5. Plug Fuelpak 4-pin connectors in-line with the connectors from step 4. 6. Unplug the TPS connector and attach T-tap connector to the center wire (yellow). (Fig 3) 7. Route the Fuelpak violet wire to T-tap. (Fig 4) 8. Reattach the TPS connector. 9. Route black wire to the front of engine and down to the horn. (Fig 5) 10. Disconnect the factory black/white wire from horn. Plug Fuelpak into horn and plug Fuelpak black/white wire to Fuelpak connector. 11. Route black and green wires to battery negative. 12. Attach Fuelpak to Fuelpak harness and mount under seat as shown. (Fig 6) 13. Before reassembling the bike, make sure handlebar switch is in the engine-not-running position and turn the key on. Fuelpak should light up. Sound the horn. If Fuelpak turns off when the horn is sounded, recheck the black wire connection on the horn and that it is connected to the correct wire from the factory harness. 14. Follow the service manual to reinstall the airbox and gas tank. INSTALLATION INSTRUCTIONS FOR P/N 65005 READ ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION FUEL INJECTION MANAGEMENT SYSTEM ROAD STAR WARRIOR NOTICE: Fuelpak is intended for racing or off-highway use only, and is not legal for sale or use in California on pollution-controlled vehicles. PLEASE NOTE: FUELPAK USE REQUIRES A HIGH PERFORMANCE AIR FILTER. HOW IT WORKS ENTERING VALUES 1. Remove Fuelpak clear case cover by removing all four screws, save hardware . 2. Turn on main power with key, but do not start engine. Fuelpak display should light up, if not, turn power off and verify the connectors are fully seated. 3. Refer to Fuelpak Setting Reference to locate the Setting Values specific to your bike and exhaust system. If you do not find your setting, visit fuelpakfi.com or call tech support at (562) 921-0071. 4. Starting with mode 1 selected, press the value (+) or the value (-) buttons to input the correct value as indicated in your Setting Value. After entering your first value, press the mode select button to move to mode 2 and enter the value. Continue until you have entered the value for each of the first 18 mode positions. Each time the value (+) is pressed, the value increases by one number. Each time the value (-) is pressed, the value decreases by one number. (Please refer to the “How It Works” section directly above if you have questions about this step. 5. As the next procedure, after you have entered in your values for the first 18 modes, press the mode select button to move to mode 19. Fully twist open the throttle and return to idle position to calibrate the Fuelpak to your bike. 6. By pressing the mode select button twice, move to mode 21 and verify that it reads “0″ with the throttle closed, “50″ at approximately half-throttle and “99″ when fully opened; if not, repeat step 5. Do not proceed to step 7 until mode 21 is verified. 7. Enter any other mode values as required for your application. 8. Turn off power. 9. Reinstall clear cover, tuck Fuelpak under seat area and reinstall seat. 10. You are now ready to ride.

Incoming search terms:

Victory Vegas Rear LED Turn Signal Assembly Installation Manual

0

Filed Under (Victory) by admin on 31-10-2010

download
Step 1 •Prior to installation it is recommended that you perform a Pre-Function check. To do so, remove the left side battery cover from the bike and expose the post terminals. Hold the positive red lead from the turn signal to the positive red lead of the battery and then place the negative black lead from the turn signal to the negative black lead of the battery. Do one side at a time and ensure that both sides light prior to installation. Step 2 •Remove seat (passenger too if installed) •Remove fender “eyelashes” (required first if passenger seat is installed) •Remove the fender mounting bolts •Disconnect the rear turn signal and taillight harness connector located in the battery box compartment •Remove the fender by gentle prying outward and upward on one side to clear the mounting points, then the other side •Set aside on a flat and smooth surface to protect the fender’s finish (you may want to wrap it in a large towel) Step 3 •Turn the rear fender assembly upside down on a stable and covered/protected surface to prevent damaging the fender/paint •Remove the rear tail assembly and disconnect the wiring harness and license plate light. THIS PART IS NO LONGER NEEDED! Victory Vegas Rear LED Turn Signal Assembly Installation Guide •Remove the stock metal spacers shown below and replace them with the ¼” rubber spacers included in your accessory/installation kit. Step 4 •Place the turn signal assembly mounting arms over the rubber spacers. Align the turn signal in place so the space between the fender and the turn signal tube is consistent. After completing this step, place a small amount of Loc-Tite to the bolt and slowly tighten the stock nuts snugly in place, (extreme over-tightening may damage turn signal or fender lip). You should not need to loosen the mounting arms which are attached to the turn signal bracket to obtain the ideal fit; they are pre-assembled to be aligned. Please also note that due to manufacturing tolerances in the production of the fender, the rolled inner lip of it may interfere with the turn signal assembly seating properly. If this is the case, the lip can be tapped down flush with a rubber mallet or other appropriate tool. Take the necessary precautions to maintain your fender’s finish should this step be necessary. Step 5 •Run the wiring of the turn signal assembly in an appropriate/desireable path to the stock wiring harness. See picture below as an example. Once the wires are run, cut any excess wire and install the bullet connectors (included in the installation/accessory package) to the end of the wires. Due to the small gauge of the wire it’s suggested that you double it over before placing it into the bullet connector and solder it in place. Wire as follows:

Incoming search terms:

Incoming search terms: