Harley Davidson Softails Shocks Installation download

0

Filed Under (Harley Davidson) by admin on 28-02-2012

download
Progressive Suspension shocks for your Softail are designed as a direct bolt on replacement for your stockers. Although they are very similar in appearance, they have vastly improved damping and spring rates. Our shocks do not use the remote reservoir system used on earlier model Softail models. 1. Place motorcycle securely on stand or blocks so the rear wheel is slightly off the ground. 2. Per instructions in a authorized shop manual, remove your old shocks. Note location of the mounting hardware. 3. Install the Progressive Suspension shocks using the stock mounting bolts and washers. 4. Tighten all shock mounting bolts to the proper torque specifications (see shop manual for specs) 5. Progressive Suspension shocks have adjustable pre-load to compensate for varying weights. The included wrench or a Harley Davidson pre-load adjustment wrench is necessary to adjust the pre-load setting. Replacement Progressive Suspension, Inc. wrenches are available as Part # SW-784 from most Dealers and Accessory Stores and the Harley Davidson wrench is available as part #94455-89 from any Harley Davidson Dealer. Spring preload is set by us to the lightest setting. To increase preload for heavier riders/loads/passengers, loosen locknut with the inside portion of the supplied wrench or a 1 1/ 16 ” wrench and back it off several turns. Use the supplied wrench or a Harley adjustment wrench to turn the adjustment nut counterclockwise to the desired preload setting. Then tighten the 11/ 16 ” lock nut. Both shocks must be adjusted to the same, equal setting

Incoming search terms:

YAMAHA V-STAR 650 CRUZER EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 28-12-2010

download
STOCK EXHAUST SYSTEM REMOVAL 1. This Exhaust system is specifically designed for California models, before continuing be sure it is the correct system for your application. 2. Loosen clamp that connects muffler to front head pipe. 3. Remove cylinder exhaust bolts from rear head pipe that connects rear head pipe to cylinder (save for re- use). 4. Remove bolts that connect mufflers to mounting bracket. Remove complete system. Note: Assistance may be required. Page 1of 4 Y411IN Rev. 1.0 YAMAHA V-STAR 650 CRUZER EXHAUST SYSTEM, CA Model Part #31505 Tools required for installation: 1/2”, 12mm & 10mm wrenches 5mm, 6mm Allen wrenches 5/16″ nutdriver / flat blade screwdriver VANCE & HINES EXHAUST SYSTEM INSTALLATION 1. Check condition of stock exhaust gaskets. Replace if damaged or worn. 2. Install mounting bracket (stamped 370-P) in the original muffler mounting position, using two 8mm bolts (supplied)(Figure 1). 3. Mark outside surface of front and rear heat shields with location of mounting clips that are welded to the inside (Figure 2). Place each heat shield on a non abrasive surface such as a blanket or carpet. Lay each head pipe/muffler onto its respective heat shield (Figure 3). 4. Loosely install each hose clamp by feeding tail end of clamp into heat shield clip (Figure 4). Take note of clamp screw head direction (Figure 3). Screw head should be accessible when system is installed on motorcycle for adjustment purposes. Note: Do not tighten yet. 5. Install T-bolt clamp onto front muffler. Slide muffler onto front head pipe. Slide dog bone shaped nut plate (supplied) inside bracket welded to backside of front muffler. Attach muffler to mounting bracket 370-P using two 5/16″ flange bolts (supplied) engaging dog bone nut plate. Leave head pipe/muffler assembly loose at this time (Figure 4). 6. Using stock Allen bolts, carefully install rear head pipe/muffler assembly into exhaust port. (Assistance may be required). Note: Do not tighten yet. 7. Slide dog bone shaped nut plate (supplied) inside bracket welded to backside of rear muffler

ELECTRIC SCOOTER Assembly and User's Manual

0

Filed Under (Tips and Review) by admin on 26-11-2010

download
l Output: 250W l Voltage: 24V DC l Rated current: 14.0A l Non-loading rotate speed: 3350±5% l Rated rotate speed: 2500 RPM l Rated torsion: 0.90 Battery l 12V 12Ah/5hr x (2) Qty l Sealed lead acid FEATURES & SPECIFICATIONS Performance l Maximum speed: 11 MPH l Range: Nine (9) miles l Incline rating: 40 l Net Weight: 45 lbs. l Maximum load cap.: 178 lbs. Tires l Tire Size: 2 1/4″ x 12 1/2″ l Tire Pressure: 45-50 PSI Key Ignition Headlight Turn Signals Turn Signals Brake Light Mag Wheels Footrests Working Gauges Quick Connect Charging 3
4 l One (1) SCOOT – N – GO™ l User/assembly manual l Tool kit containing 2 open ended wrenches, combination Phillips/Flathead head screwdriver l Spare fuses (30 Amp x 3 qty) l 24V Battery charger . Remove scooter from carton and all protective materials from the unit. 2. Use tool kit provided for installation FRONT WHEEL INSTALLATION: 1. Place wheel (D) in the center of the forks 2. Insert one (1) spacer (C) between wheel (D) and fork 3. Carefully insert axle (E) through fork, spacer (C), and wheel (D) 4.Insert one (1) spacer (C) on opposite side between fork and wheel (D) 5. Continue to insert axle (E) through fork on opposite side 6. Place washers (B) and nuts (A) on both ends of axle and tighten with open ended wrench provided in the tool kit. 7. Check nuts are tight and wheel moves freely Parts Needed A Nut Qty- 2 Lockwasher Qty- 2 B Spacer/ Bearing-holder Qty- 2 C D Front Wheel Qty- 1 E Axle Qty- 1 *Photos are not to scale Spacer Spacer Axle Washer Washer Nut Nut
10 ASSEMBLY INSTRUCTIONS HANDLEBARS INSTALLATION: 1. Insert handlebar post through tightening clamp 2. Insert the top of the fork base into bottom of handlebar post. 3. Line up handlebars and front wheel 4. Slide tightening clamp down to open end of fork base 5. Insert bolt and hand tightening nut into clamp and tighten. 6. Be sure that handlebars and wheel move at the same time

Incoming search terms: